• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.967-973
• /
• 2004

Rock socketed drilled shafts transfer significant portion of structural loads at the socketed part. Therefore, a proper design of side and base resistances of a shaft at the socket is a major concern for the geotechnical engineers. In this study, we modified the Hoek-Brown criterion to estimate side resistance of rock socketed drilled shafts. Earlier method to compute side resistance of a shaft is linear or power functions of intact rock masses. However, side resistance is mobilized like shearing which influenced by the mechanical properties of concrete and rock masses, adhesion of rock/concrete interface, roughness of rock socket. Therefore, a single coefficient or power of uniaxial compressive strength of intact rock cannot provide accurate values of side resistance in a wide range of the uniaxial compressive strength. A new approach proposed in this study can consider in situ rock mass condition (frequency or discontinuities, weathering condition), and rock types thus, it has a wider applicability than the earlier models.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 추계 학술발표회
• /
• pp.409-429
• /
• 2006

In designing rock-socketed drilled shaft, bearing capacity evaluation is very important because the maximum values of base and side resistance are not generally mobilized at the same value of displacement, FHWA and AASHTO code suggest different ultimate bearing capacity formular according to rock type and shaft settlement. In domestic code suggest base resistance and side resistance can be added on condition that after confirming the result of field load test with axial load transfer test. This paper shows that static load test and hi-directional load test result analysis of deep rock-socketed drilled shaft in three different sites. Load-settlement curve, t-z, and q-w curve in rock-socketed part were calculated and compared. t-z curve in weathered and soft rock showed no deflection softening behavior in pretty large strain (about 2-3% of diameter). Ultimate resistance could be the summation of side resistance and base resistance in rock-socketed drilled shaft in domestic sites.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.611-618
• /
• 2005

In this research, the effect of rock mass weathering on the side shear resistance of drilled shaft socketed into weathered rock was investigated. For that, a database of 23 cast-in-place concrete piles with diameters varying from 400mm to 1,500mm were socketed into weathered igneous/meta-igneous rock at four different sites. The static axial load tests were performed to examine the resistant behavior of the piles, and a comprehensive field/laboratory testing program at the field test site was also performed to describe the in situ rock mass conditions quantitatively. No correlation was found between the compressive strengths of intact rock and the side shear resistance of weathered/soft rock. The ground investigation data regarding the rock mass conditions (e.g. $E_m,\;E_{ur},\;_{plm}$, RMR, RQD, j) was found to be highly correlated with the side shear resistance, showing the coefficients of correlation greater than 0.7 in most cases. Additionally, the applicability of existing methods for the side shear resistance of piles in rock was verified by comparison with the field test data. The existing empirical relations between the compressive strength of intact rock and the side shear resistance(Horvath (1982), Rowe & Armitage(1987) etc.) appeared to overestimated the side shear resistance of all piles tested in this research unless additional consideration on the effect of rock mass weathering or fracturing was applied. The existing methods which consider the effect of rock mass condition were modified and/or extended for weathered rock mass where mass factor j is lower than 0.1, and RQD is below 50%.

• Geomechanics and Engineering
• /
• 제21권6호
• /
• pp.503-511
• /
• 2020

This study evaluated the side resistance of drilled shafts socketed into rock sections. Commonly used analysis methods for side resistance of piles in rocks are examined by utilizing a large number of load test data. The analysis of the unit side resistance of pile foundations embedded into rock sections is based on an empirical coefficient (α) and the uniaxial compressive strength (q_u) or its root (${\sqrt{q_u}}$). The Davisson criterion was used to interpret the resistance capacity from the load test results to acquire the computed relationships. The α-${\sqrt{q_u}}$ relationship is proven to be reliable in the prediction of friction resistance. This study further analyzed the relationship by including the effect of rock quality designation (RQD) on the results. Analysis results showed that the analysis model of α-${\sqrt{q_u}}$-RQD provided better prediction and reliability considering the RQD classification. Based on these analyses, the side resistance of drilled shafts socked into rocks is provided with statistical data to support the analysis.

• 한국융합학회논문지
• /
• 제10권9호
• /
• pp.161-166
• /
• 2019

본 연구에서는 A, B, C 3가지 자동차 사이드미러 모델들에 있어서의 공기 저항으로 인한 유동을 분석을 함으로서 다양한 사이드미러들 주위에서의 흐름을 연구한다. 모델 A는 사각형 모양의 사이드미러이고, 모델 B는 삼각형 모양의 사이드미러, 모델 C은 타원형 모양의 사이드미러이다. 자동차의 사이드미러의 설계를 변경함으로서 운전 시 좀 더 사이드미러의 공기저항을 줄여서 약간의 자동차의 동력을 감소시킬 수 있다. 해석 결과로서, 사이드미러에 대한 공기저항의 압력이 클수록 공기 유동속도가 큰 것을 볼 수 있었다. 그러므로 공기저항의 압력이 작을수록 유동속도가 작고 공기가 더 잘 유통된다고 판단된다. 그러므로 Model B가 가장 좋은 Model이라는 것을 확인할 수 있다. 본 연구결과를 토대로 얻은 자동차 사이드 미러의 설계데이터를 활용함으로서 실생활에서의 자동차 운전시에 그 미적 감각을 나타낼 수 있다.

• 한국지반공학회논문집
• /
• 제29권12호
• /
• pp.5-10
• /
• 2013

말뚝의 지지력은 주면마찰력과 선단지지력으로 구분할 수 있고 설계지지력을 산정 시에는 말뚝의 지지형식에 따라 두 지지력을 모두 고려하거나 둘 중의 하나만을 고려하기도 한다. 본 연구에서는 국내 현장타설말뚝의 양방향재하시험을 결과를 분석하여 각 지층별로 측정된 단위주면마찰지지력 값을 국내외의 제안식으로 산정된 값과 비교분석하였다. 토사층의 경우 SPT N 값을 이용하는 제안식 값들이 재하시험을 통하여 실측된 단위주면마찰력에 비해 작아 과소평가 되고 있음을 알 수 있었고, 암반층의 경우 국내외 제안식들이 암반의 일축압축강도를 기반으로 되어있어 코아시료 채취가 어려운 국내 풍화암이나 연암층에는 적용이 곤란하여 환산된 SPT N값을 이용한 산정식을 제안하였다. 그 결과 점성토의 단위주면마찰지지력은 $f_s{\leq}5tf/m^2$, 사질토의 단위주면마찰지지력은 $f_s{\leq}15tf/m^2$의 상한값을 제안할 수 있었다. 암반층에서는 수정 SPT N값에 따라 단위주면마찰력을 제안하였는데 풍화암층은 $15tf/m^2$ < $f_s{\leq}50tf/m^2$, 연암층은 $f_s{\geq}35tf/m^2$으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.249-258
• /
• 1999

Dynamic load and static load tests are performed on steel pipe piles and concrete piles at five construction sites in highway to compare the difference of load bearing mechanisms. At each site, one steel pile is instrumented with electric strain gages and dynamic tests are performed on the pile during installation. Damages of strain gages due to the installation are checked and static test is performed upon the same pile after two or seven days as well. It shows that load transfer from side friction to base resistance behaves somewhat differently according to the results of load-settlement analysis obtained from PDA and static load test. Initial elastic stage of load settlement curves of two load tests is almost similar. But after the yielding point, dynamic resistance of pile behaves more stiffer than static resistance, thus, dynamic load test result might overestimate the real pile capacity compared with static result. Analysis of gage readings shows that unit skin friction increases exponentially with depth. The skin friction is mobilized at the 1∼2m above the pile tip and contributes to the considerable side resistance. Comparison of side and base resistances between the measured value and the calculated value by Meyerhof's bearing capacity equation using SPT N value shows that the calculated base resistance is higher than the measured. Therefore, contribution of side resistance to total capacity shouldn't be ignored or underestimated. Finally, based upon the overall test results, a construction control procedure is suggested.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.8-9
• /
• 2021

FCP requires different curvatures and shapes according to the method of division, and it is necessary to manufacture a formwork accordingly. FCP production equipment consists of CNC equipment and side shape control equipment. This can be implemented in various shapes of upper, lower, and side surfaces. In the side shape control equipment, it is implemented as a variable side formwork. Among the required performance of the variable side formwork, there is stiffness against side pressure, which needs to be verified. Therefore, in this study, the FCP fabrication experiment is conducted with the developed variable side formwork. By analyzing the error in the shape of the fabricated FCP, the lateral pressure resistance capability of the side form is measured and verified.

• 한국지반환경공학회 논문집
• /
• 제14권10호
• /
• pp.11-16
• /
• 2013

양방향재하시험의 성공여부는 상향력과 하향력의 균형을 이룰 수 있는 재하장치 위치 선정에 달려있다. 상향력과 하향력의 균형을 이루기 위해서는 발휘되는 단위주면마찰력과 단위선단지지력의 산정이 중요한데, 국내에서 시행되는 양방향재하시험은 주로 사용말뚝에 적용되어 극한지지력까지 재하되지 않고 설계지지력을 확인하는 것이 일반적이다. 하지만 국내 외 제안된 암반층의 극한단위주면마찰력 및 허용단위주면마찰력 산정식은 암반의 일축압축강도를 기반으로 되어있고, 또한 국내 풍화암층과 RQD가 극히 낮은 연암층은 일축압축강도시험을 할 수 있는 코아를 얻기가 어려워 적용이 어려운 실정이다. 따라서 이 연구에서는 국내에서 시행되었던 양방향재하시험에서 얻은 각 지층별 발휘된 단위주면마찰력과 환산된 SPT N/cm과 관계도표를 제안하고 이 관계도표를 이용하여 실제 국내 현장의 양방향재하시험을 위한 상향력과 하향력의 균형위치를 선정하였다. 또한 선정된 균형위치에 양방향재하장치를 설치한 후 재하시험을 실시하여 측정된 각 지층의 발휘된 단위주면마찰력 값들과 균형위치 선정 시 적용한 관계도표의 값들을 비교하여 관계도표의 적정성을 분석하였다. 분석결과 풍화토층과 풍화암층에서는 거의 유사한 결과를 보였고, 연암층에서는 재하장치 상부연암층과 하부연암층에서 발휘된 측정값(상부 $1,151kN/m^2$, 하부 $1,500kN/m^2$)의 평균값($1,325kN/m^2$)도 산정값($1,250kN/m^2$)과 큰 차이를 보이지 않아 관계도표는 적정한 것으로 판단되었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.318-318
• /
• 2009

The door stiffness is one of the important factors side impact. Generally, the researches have been conducted on the assembled door module. This study is to analysis the side impact characteristics for automotives door module. The impact characteristics have been determined by door module side impact test machine. To determine the initial, intermediate and peak crush resistances use the plot of load versus displacement and obtain the integral of the applied load with respect to the crush distances specified below for each door tested. The initial crush resistance is the average force required to deform the door through the initial 6 inches of crush. The intermediate crush resistance is the average force required to deform the door through the initial 12 inches of crush. The peak crush resistance will be directly obtained from the plot of load versus displacement since it is the largest force required to deform the door through the entire 18 inches crush distance. The data are used to determine if a specific vehicle or item of automotives equipment meets the minimum performance requirements of the subject Federal Motor Vehicle Safety Standard(FMVSS). FMVSS Static 214, Side impact protection, specifies performance requirements for protection of occupants in side impact crashes.