• Journal of the Korean Geotechnical Society
• /
• v.23 no.8
• /
• pp.87-95
• /
• 2007

This study analyzed ground settlement and ground stress depending on tunnel excavation and the ground reinforcing grouting methods for double line road tunnel through deep weathered zone. Diameter of double line road tunnel was approximately 12m and umbrella arch method and side wall reinforcing grouting were applied. The ring-cut split excavation method and CD-cut excavation method for excavation method were applied. Analyses of failure rate and vertical stress ratio show that the tunnel for which the height of the cover (H) was higher than four times the diameter, can be considered a deep tunnel. Comparisons of various excavation and ground reinforcement methods showed that CD-cut method results in lower surface and crown settlement, and lower failure rate than that obtained by Ring-cut split method. In addition, the side wall reinforcing grouting resulted in reduction of tunnel displacement and settlement.

• Geomechanics and Engineering
• /
• v.21 no.1
• /
• pp.23-33
• /
• 2020

An advancing cutting roof for gob-side entry retaining with no-pillar mining under specific geological conditions is more conducive to the safe and efficient production in a coalmine. This method is being promoted for use in a large number of coalmines because it has many advantages compared to the retaining method with an artificial filling wall as the gateway side filling body. In order to observe the inner structure of the gateway cutting roof and understand its stability mechanism, an equivalent material simulation experiment for a coalmine with complex geological conditions was carried out in this study. The results show that a "self-stabilization bearing structure" equilibrium model was found after the cutting roof caving when the cut line deviation angle was unequal to zero and the cut height was greater than the mining height, and the caving roof rock was hard without damage. The model showed that its stability was mainly controlled by two key blocks. Furthermore, in order to determine the optimal parameters of the cut height and the cut line deviation angle for the cutting roof of the retaining gateway, an in-depth analysis with theoretical mechanics and mine rock mechanics of the model was performed, and the relationship between the roof balance control force and the cut height and cut line deviation angle was solved. It was found that the selection of the values of the cut height and the cut line deviation angle had to conform to a certain principle that it should not only utilize the support force provided by the coal wall and the contact surface of the two key blocks but also prevent the failure of the coal wall and the contact surface.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.95-103
• /
• 2015

This paper presents the effects of the tool shape on the geometrical characteristics of flat end-milled side walls. A tool shape is characterized by such parameters as helix angle, number of cutting edges, and diameter. The geometrical characteristics of the side walls are represented by the surface profiles in the feed and axial directions, which are orthogonal to each other. The geometrical defects in each direction are estimated based on the instantaneous apparent cutting areas, which are represented by the interference area between the tool and workpiece and that between the cutting edge and workpiece. It is confirmed that a geometrical defect in the feed direction is formed when the tool leaves the workpiece and the curvature of the tool path changes. Defects in the axial direction are also found in the side walls, except for the defect zone in the feed direction. An up-cut using an end-mill with a steeper helix angle, a greater number of cutting edges, and a smaller diameter are thus found to improve the geometrical accuracy of end-milled side walls.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.2
• /
• pp.14-19
• /
• 2022

This paper presents motion planning algorithm that yields to intervening side lane vehicles in a congested traffic flow based on vehicle to vehicle (V2V) communication. Autonomous driving in dense traffic situation requires advanced driving performance in terms of vehicle interaction and risk mitigation. One of the most important functions necessary for congested traffic autonomous driving is to predict the lane change intention of the side lane target vehicle. However, implementing this function by using only environmental sensors has limitations. In this study, V2V communication is used to overcome the limitations and determine the intention of cut-in vehicles. Lane change intention of the intervening side lane vehicle is inferred by its longitudinal speed, steering angle, and turn signal light information received by the on-board-unit (OBU). Once the yield decision is made, the subject vehicle decelerates to generate sufficient clearance for the target vehicle to enter. Validation of the algorithm was conducted with actual autonomous test vehicles.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.127-134
• /
• 2000

Soil nailing is in-situ ground improvement technique of reinforcing soils using passive inclusions for the purpose of slope stability. Also soil nailing, in general, was used and studied as a reinforcement technique at cut slope, but this paper presents the results of study for soil nailing application as a reinforcement technique at the banking over slided slope. In-situ pull-out tests of nails, instrumented with strain gauges, were performed to investigate the maximum pull-out load and to calculate the unit side resistance in each different layer. And the apparent average unit side resistance of this study was compared with that of other sites installed at cut slope.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1269-1278
• /
• 2013

The cutting area changes periodically in the end-milling process because of its form generation mechanism. In this study, the effects of the cutting area on end-milled side walls are studied by developing a cutting area model that simulates the area formed by engagement between a workpiece and a cutting edge of the end mill. To do this, the straightness profile of the side wall in the axial direction is investigated. Models for estimating the cutting area and the transition point, where the slope of the straightness profile changes suddenly, are verified from real end-milling experiments under various radial and axial depth of cut conditions. Through this study, it is confirmed that the final end-milled side wall is generated in the regions where cutting areas are constant and decreasing in the down-cut. Similarly, in stable up-cut, it is also generated in the regions where cutting areas are increasing and constant. It is found that the transition point appears when the region changes.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.33 no.6
• /
• pp.919-928
• /
• 2023

Deep learning technology is used in various fields such as self-driving cars, image creation, and virtual voice implementation, and deep learning accelerators have been developed for high-speed operation in hardware devices. However, several side channel attacks that recover secret information inside the accelerator using side-channel information generated when the deep learning accelerator operates have been recently researched. In this paper, we implemented a DNN(Deep Neural Network)-based MNIST digit classifier on a microprocessor and attempted a correlation power analysis attack to confirm that the weights of deep learning accelerator could be sufficiently recovered. In addition, to counter these power analysis attacks, we proposed a Node-CUT shuffling method that applies the principle of misalignment at the time of power measurement. It was confirmed through experiments that the proposed countermeasure can effectively defend against side-channel attacks, and that the additional calculation amount is reduced by more than 1/3 compared to using the Fisher-Yates shuffling method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.547-552
• /
• 2003

In mold machining, there are many concave machining regions where chatter and tool deflection occur since MRR (material removal rate) increases as curvature increases even though cutting speed and depth of cut are constant. Boolean operation between stock and tool model is widely used to compute MRR in NC milling simulation. In finish cutting, the side step is reduced to about 0.3mm and tool path length is sometimes over 300m. so Boolean operation takes long computation time and includes much error if the resolution of stock and tool model is larger than the side step. In this paper, curvature of CL(cutter location) surface and side step of tool path is used to compute the feedrate for constant MRR machining. The data structure of CL surface is Z-map generated from NC tool path. The algorithm to get local curvature from discrete data was developed and applied to compute local curvature of CL surface. The side step of tool path was computed by point density map which includes cutter location point density at each grid element. The feedrate computed from curvature and side step is inserted to new tool path to regulate MRR. The resultants wire applied to feedrate optimization system which generates new tool path with feedrate from NC codes for finish cutting. The system was applied to speaker mold machining. The finishing time was reduced to 12.6%. tool wear was reduced from 2mm to 1.1mm and chatter marks and over cut on corner were removed.

• Journal of Korean Society on Water Environment
• /
• v.34 no.1
• /
• pp.96-108
• /
• 2018

Large efforts have recently been made on research and development of sustainable and energy-efficient short-cut nitrogen removal processes owing to strong attention to the energy neutral/positive wastewater treatment system. Anaerobic ammonium oxidizing bacteria (anammox bacteria) have been highlighted since 1990's due to their unique advantages including 60% less energy consumption, nearly 100% reduction for carbon source requirement, and 80% less sludge production. Side-stream short-cut nitrogen removal using anammox bacteria and partial nitritation anammox (PN/A) has been well established, whereas substantial challenges remain to be addressed mainly due to undesired main-stream conditions for anammox bacteria. These include low temperature, low concentrations of ammonia, nitrite, free ammonia, free nitrous acid or a combination of those. In addition, an anammox side-stream nitrogen management is insufficient to reduce overall energy consumption for energy-neutral or energy positive water resource recovery facility (WRRF) and at the same time to comply with nitrogen discharge regulation. This implies the development of the successful main-stream anammox based technology will accelerate a conversion of current wastewater treatment plants to sustainable water and energy recovery facility. This study discusses the status of the research, key mechanisms & interactions of the protagonists in the main-stream PN/A, and control parameters and major challenges in process development.

• Journal of the Korean Institute of Gas
• /
• v.21 no.4
• /
• pp.70-75
• /
• 2017

This paper presents the FEM analysis results on the deformation behavior safety of automatic cut-off horizontal and conventional vertical gas valves. Based on the FEM analysis, the primary maximum deformation of $4.4{\mu}m$ was formed on the right end side of a valve body when the internal gas pressure was supplied on the screw port and gas discharge port of an automatic cut-off horizontal gas valve. And the secondary maximum deformation of $2.9{\mu}m$ was formed on the end side of safety valve port. This small deformation of an automatic cut-off horizontal gas valve is strongly related to the balanced design of a horizontal gas valve main body, which is composed of a screw part, gas outlet port, port for a stem and spindle shaft assembly, and safety valve port. But, the primary maximum deformation of 0.076mm was formed on the upper part of a conventional automatic cut-off vertical gas valve when the internal gas pressure was supplied on the screw port and gas discharge port. And the secondary maximum deformation of 0.055mm was formed on the left end side of a gas outlet port. This may effect on the sealing clearance of o-ring that is inserted on the groove of an automatic cut-off unit. Thus, this paper recommends an automatic cut-off horizontal gas valve compared with that of a conventional gas valve for a gas leakage free mechanism of a LPG cylinder valve.