• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.5 s.347
• /
• pp.11-16
• /
• 2006

This paper reports the correlation between dielectric constant and degree of amorphism of the hybrid type SiOC thin films. SiOC thin films were deposited by high density plasma chemical vapor deposition using bistrimethyl- silylmethane(BTMSM,$H_{9}C_{3}-Si-CH_{2}-Si-C_{3}H_{9}$) and oxygen precursors with various flow rate ratio. As-deposited film and annealed films at $400^{\circ}C$ were analyzed by XRD. The SiOC thin films were amorphous from XRD patterns. For quantitative analysis, the diffraction pattern of the samples was transformed to radial distribution function by Fourier analysis, and then compared with each other. The degree of amorphism of annealed films was higher than that of as-deposited ones. The dielectric constant varied in accordance with flow rate ratio of precursors. The lowest dielectric constant was obtained from the as-deposited film which has the highest degree of amorphism after annealing.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.130-135
• /
• 2003

Low dielectric constant SiOC(-H) films have been prepared by inductively coupled plasma chemical vapor deposition using bis-trymethylsilyl-methane (BTMSM) and $O_2$ precursors. The annealing effects on the structural and electrical properties were studied. The results indicate post-annealing could efficiently remove the hydroxyl (-OH) related groups from the as-deposited films and cause the chemical structure re-arrangement, resulting in the more nano-pores being formed in the annealed SiOC(-H) films. The dielectric constant decreased from 2.7 to 2.1, and the refractive index decreased from 1.427 to 1.32.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.11a
• /
• pp.34-35
• /
• 1993

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.2
• /
• pp.69-72
• /
• 2012

In this study, deposition of low-dielectric constant SiOC(H) films by conventional plasma-enhanced chemical vapor deposition (PECVD) were investigated through various characterization techniques. The results show that, with an increase in the plasma power density, the relative dielectric constant (k) of the deposited films decreases whereas the refractive index increases. This is mainly due to the incorporation of organic molecules with $CH_3$ group into the Si-O-Si cage structure. It is as confirmed by FT-IR measurements in which the absorption peak at 1,129 $cm^{-1}$ corresponding to Si-O-Si cage structure increases with power plasma density. Electrical characterization reveals that even after fast thermal annealing process, the leakage current density of the deposited films is in the order of $10^{-11}$ A/cm at 1.5 MV/cm. The reliability of the SiOC(H) film is also further characterized by using BTS test.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.3
• /
• pp.1-4
• /
• 2008

The chemical shift of SiOC film was observed according to the flow rate ratio. SiOC film had the broad main band of $880\sim1190cm^{-1}$ and the sharp Si-$CH_3$ bond at $1252cm^{-1}$, and the peak position of the main bond in the infrared spectra moved to high frequency according to the increasing of an BTMSM flow rate. So the increment of the alkyl group induced the C-H bond condensation in the film, and shows the blueshift in the infrared spectra. In the case of P5000 system of Applied Materials Corporation, the strong bond of Si-CH3 bond in precursor does not enough to dissociated and ionized, because low plasma energy due to the capactive coupled CVD. Therefore, there was the sharp peak of Si-$CH_3$ bond at $1252cm^{-1}$.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.600-605
• /
• 2010

In order to meet the requirements of faster speed and higher packing density for devices in the field of semiconductor manufacturing, the development of Cu/Low k device material is explored for use in multi-layer interconnection. SiOC(-H) thin films containing alkylgroup are considered the most promising among all the other low k candidate materials for Cu interconnection, which materials are intended to replace conventional Al wiring. Their promising character is due to their thermal and mechanical properties, which are superior to those of organic materials such as porous $SiO_2$, SiOF, polyimides, and poly (arylene ether). SiOC(-H) thin films containing alkylgroup are generally prepared by PECVD method using trimethoxysilane as precursor. Nano voids in the film originating from the sterichindrance of alkylgroup lower the dielectric constant of the film. In this study, methyltriphenylsilane containing bulky substitute was prepared and characterized by using NMR, single-crystal X-ray, GC-MS, GPC, FT-IR and TGA analyses. Solid-state NMR is utilized to investigate the insoluble samples and the chemical shift of $^{29}Si$. X-ray single crystal results confirm that methyltriphenylsilane is composed of one Si molecule, three phenyl rings and one methyl molecule. When methyltriphenylsilane decomposes, it produces radicals such as phenyl, diphenyl, phenylsilane, diphenylsilane, triphenylsilane, etc. From the analytical data, methyltriphenylsilane was found to be very efficient as a CVD or PECVD precursor.

• New & Renewable Energy
• /
• v.2 no.3
• /
• pp.31-36
• /
• 2006

Superstrate pin amorphous silicon thin-film(a-Si:H) solar cells are prepared on $SnO_2:F$ and ZnO:Al transparent conducting oxides(TCO) in order to see the effect of TCO/p-layers on a-Si:H solar cell operation. The solar cells prepared on textured ZnO:Al have higher open circuit voltage VOC than cells prepared on $SnO_2:F$. Presence of thin microcrystalline p-type silicon layer(${\mu}c-Si:H$) between ZnO:Al and p a-SiC:H plays a major role by causing improvement in fill factor as well as $V_{OC}$ of a-Si:H solar cells prepared on ZnO:Al TCO. Without any treatment of pi interface, we could obtain high $V_{OC}$ of 994mV while keeping fill factor(72.7%) and short circuit current density $J_{SC}$ at the same level as for the cells on $SnO_2:F$ TCO. This high $V_{OC}$ value can be attributed to modification in the current transport in this region due to creation of a potential barrier.

• Journal of the Korean Vacuum Society
• /
• v.18 no.6
• /
• pp.453-458
• /
• 2009

SiOC film was deposited by the chemical vapor deposition using BTMSM and oxygen mixed precursor. The characteristic of SiOC film varied with increasing of the gas flow rate ratios. The dielectric constant was obtained by C-V measurement using the structure of metal/SiOC film/Si. The space effect due to the steric hindrance between alkyl group at terminal bond of Si-$CH_3$ made the pores, and increased the thickness. However, the SiOC film due to the lowering of the polarization decreased the thickness and then decreased the dielectric constant. After annealing process, the dielectric constant decreased because of the evaporation of the OH or $H_2O$ sites. The thickness was related to the lowering of the dielectric constant by the reduction of the polarization and the thickness decreased with the decrease of the dielectric constant. The refractive index was in inverse proportion to thickness. The trends of the thickness and refractive index did not change after annealing.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.36.2-36.2
• /
• 2009

Low dielectric materials have been great attention in the semiconductor industry to develop high performance interlayer dielectrics with low k for Cu interconnect technology. In our study, the dielectric properties of SiOC /SiO2 thin film derived from polyphenylcarbosilane were investigated as a potential interlayer dielectrics for Cu interconnect technology. Polyphenylcarbosilane was synthesized from thermal rearrangement of polymethylphenylsilane around $350^{\circ}C{\sim}430^{\circ}C$. Characterization of synthesized polyphenylcarbosilane was performed with 29Si, 13C, 1H NMR, FT-IR, TG, XRD, GPC and GC analysis. From FT-IR data, the band at 1035 cm-1 is very strong and assigned to CH2 bending vibration in Si-CH2-Si group, indicating the formation of the polyphenylcarbosilane. Number average of molecular weight (Mn) of the polyphenylcarbosilane synthesized at $400^{\circ}C$ for 6hwas 2, 500 and is easily soluble in organic solvent. SiOC/SiO2 thin film was fabricated on ton-type silicon wafer by spin coating using 30wt % polyphenylcarbosilane incyclohexane. Curing of the film was performed in the air up to $400^{\circ}C$ for 2h. The thickness of the film is ranged from $1{\mu}m$ to $1.7{\mu}m$. The dielectric constant was determined from the capacitance data obtained from metal/polyphenylcarbosilane/conductive Si MIM capacitors and show a dielectric constant as low as 2.5 without added porosity. The SiOC /SiO2 thin film derived from polyphenylcarbosilane shows promising application as an interlayer dielectrics for Cu interconnect technology.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.12
• /
• pp.573-577
• /
• 2005

[$TiO_2$] sol and $SiO_2$ sol were prepared using sol-gel method. As $H_{2}O$/Alkoxide ratios increased, sol had cluster structure and as $H_{2}O$/Alkoxide ratios decreased, sol had linear structure. Gelation time of $TiO_2$ sol was faster than that of $SiO_2$ sol according to the time. In comparison with initial viscosity between $TiO_2$ sol and $SiO_2$ sol, $TiO_2$ sol was highest at $H_{2}O/Ti(OC_{3}H_{7})_{4}=5$, $SiO_2$ sol was almost constant according to $H_{2}O/Si(OC_{2}H_{5})_{4}$ ratios.