• Advanced Composite Materials
• /
• 제18권4호
• /
• pp.351-364
• /
• 2009

The thermal stability and elevated temperature mechanical properties of $SiC_P$/Al-11.7Fe-1.3V-1.7Si (Al-11.7Fe-1.3V-1.7Si reinforced with SiC particulates) composites sheets prepared by spray deposition (SD) $\rightarrow$ hot pressing $\rightarrow$ rolling process were investigated. The experimental results showed that the composite possessed high ${\sigma}_b$ (elevated temperature tensile strength), for instance, ${\sigma}_b$ was 315.8 MPa, which was tested at $315^{\circ}C$, meanwhile the figure was 232.6 MPa tested at $400^{\circ}C$, and the elongations were 2.5% and 1.4%, respectively. Furthermore, the composite sheets exhibited excellent thermal stability: the hardness showed no significant decline after annealing at $550^{\circ}C$ for 200 h or at $600^{\circ}C$ for 10 h. The good elevated temperature mechanical properties and excellent thermal stability should mainly be attributed to the formation of spherical ${\alpha}-Al_{12}(Fe,\;V)_3Si$ dispersed phase particulates in the aluminum matrix. Furthermore, the addition of SiC particles into the alloy is another important factor, which the following properties are responsible for. The resultant Si of the reaction between Al matrix and SiC particles diffused into Al matrix can stabilize ${\alpha}-Al_{12}(Fe,\;V)_3Si$ dispersed phase; in addition, the interface (Si layer) improved the wettability of Al/$SiC_P$, hence, elevated the bonding between them. Furthermore, the fine $Al_4C_3$ phase also strengthened the matrix as a dispersion-strengthened phase. Meanwhile, load is transferred from Al matrix to SiC particles, which increased the cooling rate of the melt droplets and improved the solution strengthening and dispersion strengthening.

• 한국세라믹학회지
• /
• 제37권6호
• /
• pp.545-551
• /
• 2000

Sintering behaviors of the glass-alumina composites for low firing temperature were investigated as a function of the particle size of glass frit. The system of glass frit was Pb-B-Si-Al-O. The median particle sizes of the glass frits were 2.72$\mu\textrm{m}$, 2.67$\mu\textrm{m}$ and 1.33$\mu\textrm{m}$, which were prepared with changing ball-milling times as 24 h, 48 h and 96 h. The glass-alumina composites showed maximum density at certain temperature, and further heating led to dedensification behaviors, so called over-firing. The sintering temperature, which showed maximum density, raised from 425$^{\circ}C$ to 475$^{\circ}C$ with increase of particle size of glass frit from 1.33$\mu\textrm{m}$ to 2.72$\mu\textrm{m}$. Especially, the over firing behaviors, which were occurred at high sintering temperatures, were greatly increased with decrease of particle size of glass frit.

• 한국환경과학회지
• /
• 제14권8호
• /
• pp.761-770
• /
• 2005

Scanning electron microscopy / energy dispersive X-ray analyzer(SEM/EDX) has played an important role for evaluation the source of atmospheric particle because it is a powerful tool for characterizing individual particles. The SEM/EDX system provides various physical parameters like optical diameter, as well as chemical information for a particle-by-particle basis. The purpose of the study was to classify individual particle emitted from the point sources based on clustering analysis and physico-chemical analysis by SEM/EDX. The total of 490 individual particle were analyzed at 8 point sources including coal-fired power plant, incinerator, H-C oil boiler, and metal manufacturing industry. The main components were Si and AI in the coal-fired power plant, Cl and Na in the domestic waste Incinerator, S in the H-C oil boiler and S and Fe in the metal manufactory industry, respectively.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.266-270
• /
• 2004

SiC materials have been extensively studied for high temperature components in advanced energy system and advanced gas turbine because it has excellent high temperature strength, low coefficient of thermal expansion, good resistance to oxidation and good thermal and chemical stability etc. However, the brittle characteristics of SiC such as low fracture toughness and low strain-to fracture still impose a severe limitation on practical applications of SiC materials. For these reasons, SiC/SiC composites can be considered as a promising for various structural materials, because of their good fracture toughness compared with monolithic SiC ceramics. But, high temperature and pressure lead to the degradation of the reinforcing jiber during the hot pressing. Therefore, reduction of sintering temperature and pressure is key requirements for the fabrication of SiC/SiC composites by hot pressing method. In the present work, monolithic Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method in Ar atmosphere at $1800^{\circ}C$ under 20MPa using $Al_2O_3,\;Y_2O_3\;and\;SiO_2$ as sintering additives in order to low sintering temperature and sintering pressure. The starting powder was high purity $\beta-SiC$ nano-powder with all average particle size of 30mm. The characterization of LPS-SiC was investigated by means of SEM and three point bending test. Base on the composition of sintering additives-, microstructure- and mechanical property correlation, tire compositions of sintering additives are discussed.

• 환경위생공학
• /
• 제6권1호
• /
• pp.47-62
• /
• 1991

Yellow Sand Phenomena was observed from April 8 th to 10 th in 1990. During this period particle was collected to investigate the chacteristics of chemical composition of particulate by High Volume Air Sampler and Andersen Air Sa~npler in Seoul. During this period the particle concentration was 350 yg/$m^3$ and the anions, cations, and metal concentrations were increased and the orders of these were $S0_4\;^{-2}>N0_3\;^->Cl^->F^-, Na^+>Ca^{+2}>NH_4\;^+>Mg^{2+}>K^+$, and Fe>Al>Si>Zn>Pb respectively. The principal source of Yellow Sand were identified soil and sea salt. Mn used by the trace element of soil, the persentage of contribution from soil was calculated to be about 81.3% for the particle increased by Yellow Sand Phenomena. Also the principal chemical compounds of particle were estimate metals(Fe, Al, Si, Zn) oxides, $CaSO_4, NaSO_4, MgSO_4, NaC1, MgCl_2$ and $(NH_4)_2SO_4$.

• 한국주조공학회지
• /
• 제23권1호
• /
• pp.30-39
• /
• 2003

Porous hybrid preforms were fabricated by reactive sintering using the compacts consisting of SiC particles, Fe and Al powders. Squeeze casting processing was employed to produce the composite in which the matrix phase is Al-Si7Mg. The microstructural change and wear resistance of the composites were investigated in terms of an amount of SiC particles. The wear loss was increased with increasing the contact pressure in the alloy containing SiC particles coated with Cu. The most drastic change was found to the specimen tested at 2.5 MPa of contact pressure. Concerning the alloys containing SiC particles coated with Ni-P, a drastic increase in the wear loss exhibited at 2 MPa of contact pressure in those alloys containing 4 and 8 wt. % of SiC particles coated with Ni-P. In the alloy containing 16 wt. % a proportional increase in wear loss was observed to the change of contact pressure. With respecting to the sliding velocity, the wear loss of the alloy containing SiC particles coated with Cu increased at the initial stage of wear process and then decreased. Similar result was found in the alloys containing SiC particles coated with Ni-P. On the basis of the present results obtained, it was found that wear resistance of the alloys tested was improved to show in the order of the alloy reinforced by coated SiC particles > by uncoated SiC particles > by intermetallic compound without SiC particles.

• 한국재료학회지
• /
• 제11권8호
• /
• pp.636-640
• /
• 2001

PDP용 녹색 형광체의 발광특성을 개선시키기 위해 고안된 액상의 화학적 합성법을 사용하여 조성식이 $Zn_{2-x}$ $SiO_4$:xMn(x=0.05, 0.08)인 형광체를 입자크기가 0.5~2$\mu\textrm{m}$로 조절하여 제조하였다. 제조된 형광체 입자는 구상이며 잘 분산된 형상을 봉주었고, 고상반응법에 비해 상대적으로 낮은 $1080^{\circ}C$에서 willemite구조의 단일상을 얻을 수 있었다. 또한 진공 자외선 영역의 147 nm의 여기원을 사용하여 광발광 특성을 조사하였다. 입자의 크기가 1$\mu\textrm{m}$이고 Mn의 도핑양이 8mole%일 때, 상용 형광체와 비교하여 발광세기는 약 40% 향상되었고 색좌표는 x=0.24, y=0.69로 거의 일치하는 결과를 얻을 수 있었다. 측정된 형광체의 잔광시간은 7.8ms이었다.

• 한국재료학회지
• /
• 제11권8호
• /
• pp.363-363
• /
• 2001

PDP용 녹색 형광체의 발광특성을 개선시키기 위해 고안된 액상의 화학적 합성법을 사용하여 조성식이 $Zn_{2-x}$ $SiO_4$:xMn(x=0.05, 0.08)인 형광체를 입자크기가 0.5~2$\mu\textrm{m}$로 조절하여 제조하였다. 제조된 형광체 입자는 구상이며 잘 분산된 형상을 봉주었고, 고상반응법에 비해 상대적으로 낮은 $1080^{\circ}C$에서 willemite구조의 단일상을 얻을 수 있었다. 또한 진공 자외선 영역의 147 nm의 여기원을 사용하여 광발광 특성을 조사하였다. 입자의 크기가 1$\mu\textrm{m}$이고 Mn의 도핑양이 8mole%일 때, 상용 형광체와 비교하여 발광세기는 약 40% 향상되었고 색좌표는 x=0.24, y=0.69로 거의 일치하는 결과를 얻을 수 있었다. 측정된 형광체의 잔광시간은 7.8ms이었다.

• 한국표면공학회지
• /
• 제39권4호
• /
• pp.160-165
• /
• 2006

Ni-SiC composite coating layers were prepared by electroplating method and their deposition rate, codeposition of SiC, morphology, surface roughness, hardness, wear and friction properties were investigated. It was found that the deposition rate and the codeposition of SiC in the composite coating layer increased with increasing concentration of SiC in the solution only at the early stage. Both of them reached certain maxima and then decreased with increasing concentration of SiC. Rough surface was obtained with increasing codeposition of SiC, which is probably due to the agglomeration of the SiC particle in the vicinity of surface. Vickers hardness increased with increasing codeposition of SiC and heat treatment at $300^{\circ}C$ in air for 1 hour. Wear volume decreased with increasing codeposition of SiC and friction coefficient increased with increasing codeposition of SiC at the early stage, and it became almost constant. Such wear and friction behaviors are desirable for the practical application.

• 한국세라믹학회지
• /
• 제39권10호
• /
• pp.948-954
• /
• 2002

차세대 발전 시스템에서 사용되는 고온 가스 필터용 지지층 소재를 제조하기 위하여 용융 Si 침윤 방법으로 기공율이 32∼36%, 주기공 크기가 37∼90 ${\mu}m$ 범위를 갖는 고강도 다공질 반응소결 탄화규소(RBSC)를 개발하였다. 반응소결 탄화규소 다공체의, 최대 파괴강도는 120MPa이었으며, 용융 Si 침윤 방법으로 제조된 반응소결 탄화규소 다공체에서는 SiC 입자 사이에 SiC/Si로 이루어진 기지상이 형성되어 있기 때문에 파괴 강도 및 열충격 특성이 점토 결합 탄화규소 다공체 보다 우수하였다. 반응소결 탄화규소 다공체의 기공율 및 기공 크기는 잔류 Si의 양 및 성형체에 사용한 SiC 입자 크기에 따라 다르게 나타났다.