• Tribology and Lubricants
• /
• 제9권2호
• /
• pp.63-69
• /
• 1993

The wear properties of two types of $Si_3N_4$(silicon nitride) exposed to high and low humidity were examined experimentally for various sliding speed. Bearing steel was used as the disk material at pin-on-disk type sliding. Wear rates of pressureless sintered-plus-hot-isostatic pressed Si3N4 were slightly lower than those of pressureless sintered $Si_3N_4$. It was observed that adsorbed moisture and sliding speed markedly influenced the wear properties of $Si_3N_4$. The highest wear rate was obtained under the high humidity and low sliding speed condition. As the sliding speed was increased, wear rates were decreased and the humidity effect on the wear rates of $Si_3N_4$ was lowered. The result that the $Si_3N_4$ pin showed a high wear rate under the high humidity condition was explained by the property change due to the adsorbed moisture, plowing action by the hard particles of $Fe_2O_3$ from the disk, and the corrosion effect at $Si_3N_4$ surface. Increase in sliding speed was supposed to have reduced the humidity effect on wear rate of $Si_3N_4$ by raising the temperature of both the bearing steel disk and $Si_3N_4$ pin specimen.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.59-59
• /
• 2009

The influences of B and Si in the filler metals on microstructure and isothermal solidification during transient liquid-phase (TLP) bonding of a nitrogen-containing duplex stainless steel with MBF-30 (Ni-4.5wt.%Si-3.2wt.%B) and MBF-35 (Ni-7.3wt.%Si-2.2wt.%B), were studied at the temperature range of $1030-1090^{\circ}C$ with various times from 60 s to 3600 s under a vacuum of approximately $10^{-5}$ Torr. In case of the former, BN, $Ni_3B$ and $Ni_3Si$ precipitates were formed in the bonding region. BN and $Ni_3Si$ secondary phases were present in the joint for the latter case. The formation of $Ni_3B$ within the joint centerline is dependent on B content. The morphology of $Ni_3Si$ is dominated by Si concentration. A difference between the times for complete isothermal solidification obtained by the experiments and the conventional TLP bonding diffusion model was observed when using MBF-35. According to the simulated results, the isothermal solidification completion time for MBF-35 case was smaller than that in MBF-30. However, this experimental value obtained using MBF-35 was notably larger than that obtained using MBF-30. Isothermal solidification of liquid MBF-30 is controlled by the first isothermal solidification regime dependent on B diffusion model, whereas that of liquid MBF-35 experiences two isothermal solidification regimes and is mainly controlled by the second isothermal solidification dependent on Si diffusion model. In addition, only if Si content exceeds a critical value, the slower 2nd solidification regime will commence.

• 환경위생공학
• /
• 제24권3호
• /
• pp.55-61
• /
• 2009

Fe-V is used as raw material of vanadium in the steel making process. The purpose of this study, Fe-V is to replace the $VO_{4}$. So the distribution behavior of vanadium in $VO_{4}$ of the steel investigated. The distribution ratio of the vanadium where potential of the free oxygen ion will increase in slag decreased. When CaO and MgO content which is a basic oxide from CaO-$SiO_2$-FetO-MgOsatd. slag increases, S distribution ratio increases. CaO-$SiO_2$-FetO-MgOsatd. slag better than CaO-$SiO_2$-$Al_2O_3$-MgO slag is the recovery of vanadum and desulfurization.

• Journal of Welding and Joining
• /
• 제24권4호
• /
• pp.15-21
• /
• 2006

The aim of present study is to investigate the effect of welding parameters and heat treatment conditions on the formability of the $CO_2$ laser welded silicon steel sheet. It was found that there is optimum range of the heat input ($0.6{\sim}0.7kJ/cm$) and gap distance ($0.125{\sim}0.150mm$) for the high tensile strength and the avoidance of the fracture in weld metal. Also, it was essential fur the improvement of formability to perform pre- and post-welding heat treatment which cause the uniform mixture of base metal and welding consumable.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.101-102
• /
• 2003

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1994년도 특별강연 및 추계학술발표 개요집
• /
• pp.40-43
• /
• 1994

• 대한기계학회논문집A
• /
• 제34권8호
• /
• pp.1015-1021
• /
• 2010

본 연구에서는 반응소결 탄화규소(RS-SiC)의 제조공정 중에서 C/SiC 복합 비율(0.1, 0.3, 0.4, 0.5, 0.6, 0.7, 1.0)이 외부입자충격 손상 거동에 미치는 영향을 평가하였다. 충격시험은 공기총(air-gun)을 사용하였으며, 직경 2 mm 강구를 113 m/s, 122 m/s, 180 m/s의 충격속도로 RS-SiC 판재($20\times20\times3$ mm)에 충격시켜 발생된 링크랙의 직경 변화 및 콘크랙의 발생 거동을 SEM 영상으로 평가하였다. 결과적으로 RS-SiC에 발생한 링크랙의 최대직경이 충격속도가 증가함에 따라 대체로 증가하였지만, C/SiC 복합 비율에 따라서는 급격한 변화를 보였다. 이는 C/SiC 복합 비율에 따라 잔류 Si 함량 및 굽힘강도 변화의 영향으로 볼 수 있다. 특히 C/SiC 복합 비율이 0.4~0.5 범위에서 콘크랙이 발생됨에 따라 링크랙에서 콘크랙의 발생으로 변화되는 충격손상 메커니즘의 임계영역으로 판단할 수 있다. 아울러 콘크랙의 발생 임계영역을 고려할 때, RS-SiC 최적 제조 공정으로서 C/SiC 혼합 비율을 최대 0.3으로 하는 것이 효과적이다.

• Advances in concrete construction
• /
• 제12권6호
• /
• pp.499-505
• /
• 2021

Geopolymer binders fascinate the attention of researchers as a replacement to cement binder in conventional concrete. One-ton production of cement releases one ton of carbon-dioxide in the atmosphere. In the replacement of cement by geopolymer material, there are two advantages: one is the reduction of CO₂ in the atmosphere, second is the utilization of Fly ash and Ground granulated blast furnace slag (GGBFS) are by-products from coal and steel industries. This paper focuses on the mechanical properties of steel fiber reinforced geopolymer concrete. The framework considered in this research work is geopolymer source (Fly ash, GGBFS and crimped steel fibre) and alkaline activator which consists of NaOH and Na₂SiO₃ of molarity 8M. Here the Na₂SiO₃ / NaOH ratio was taken as 2.5. The variables considered in this experimental work include Binder content (360,420 and 450 kg/m³), the proportion of Fly ash and GGBS (70-30, 60-40 and 50-50) for three different grades of Geopolymer concrete (GPC) GPC 20, GPC 40 and GPC 60. The percentage of crimped steel fibres was varied as 0.1%, 0.2%, 0.3%, 0.4% and 0.5%. Generally, the inclusion of steel fibres increases the flexural and split tensile strength of Geopolymer concrete. The optimum dosage of steel fibres was found to be 0.4% (by volume fraction).

• Journal of Korean Vacuum Science & Technology
• /
• 제6권1호
• /
• pp.46-50
• /
• 2002

C-SiC films with different content of SiC on stainless steel substrate were prepared with ion beam mixing. It was found that hydrogen concentrations in C-SiC coatings was higher than that in stainless steel after H$\^$+/ ion implantation followed by thermal annealing. Infrared (IR) transmission measurement was used to study the mechanism of hydrogen retention by C-SiC films. The vibrational features in the range between 400 and 3200 cm$\^$-1/ in IR transmission spectra show the Si-CH$_3$, Si-CH$_2$, Si-H, CH$_2$and CH$_3$bonds, which are responsible for retaining hydrogen.

• 한국세라믹학회지
• /
• 제42권2호
• /
• pp.88-93
• /
• 2005

아크 이온 플레이팅과 스퍼터로 구성된 하이브리드 시스템을 이용하여 다성분계 Ti-Al-Si-N 코팅막을 WC-Co 기판에 증착하였다. 증착시 Si 함량을 변화시켜 코팅막의 마모특성에 Si 함량이 미치는 영향에 대하여 조사하였다. 마모 특성을 관찰하기 위하여 Ti-Al-Si-N 코팅막이 증착된 WC-Co 원판에 3N의 하중, 0.1 m/s의 속도로 볼 온 디스크(ball-on-disk) 형태의 마모시험기를 이용하여 건식 마모 실험을 하였다. 상대재로는 스틸볼과 지르코니아볼을 사용하였다. 상대재가 스틸볼의 경우 Ti-Al-Si-N 코팅막의 마찰계수가 Ti-Al-N 코팅막의 마찰계수보다 낮게 나타났다 이는 Si가 첨가되어 마모시 상대재와 코팅막 사이에 자기윤활효과(self-lubricant effect)에 의한 것으로 여겨진다. 코팅막과 스틸볼 사이에 응착 마모 거동을 보였으며, Si의 함량이 증가함에 따라 마찰계수는 감소하였다. 한편, 상대재가 지르코니아 볼의 경우 코팅막과 지르코니아 볼 사이에서 연삭마모 거동이 더 지배적이었고, Si 함량이 증가할수록 마찰계수는 증가하였다.