• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.162-165
• /
• 2006

In this study, Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method with $\beta$-SiC powder whose a particle size is 30nm and less on the average in argon condition at 1780 and $1800^{\circ}C$ under 20MPa. Alumina ($Al_2O_3$), yttria ($Y_2O_3$) and silica ($SiO_2$) were used for sintering additives. To investigate effects of particle-size and temperature on $SiO_2$, LPS-SiC was fixed $Al_2O_3$, $Y_2O_3$ and then particle-size of $SiO_2$ were changed as two kinds. The system of particle-size and temperature on sintering additives which affects a property of sintering os well os the influence depending on particle-size and temperature of sintering additives were investigated by measurement of sintering properties. Such as measurement of sintering density, vikers hardness and observing of microstructure were investigated to make sure of the optimum condition which is about matrix of $SiC_f/SiC$ composites. Base on the composition of sintering additives, microstructure and sintering property correlation, the effect of particle-size of sintering additives are discussed. An experimental method to investigate the dynamic characteristics of bums in extreme environmental condition is established.

• Korean Chemical Engineering Research
• /
• 제61권1호
• /
• pp.39-44
• /
• 2023

본 연구에서는 습식 분극을 통하여 Si 다결정의 입자 크기를 조절을 하였으며, 입자 크기에 따른 Si 음극활물질의 용량 및 수명 특성 변화를 관찰하였다. 진동밀로 분쇄한 Si 입자를 습식법으로 분급한 시료의 입도를 분석한 결과 Si의 불균일한 입자 분포가 균일하게 조절이 되었다. Si를 24시간 분급한 시료의 d₅₀이 0.50 ㎛로 감소하였다. 전기화학적 특성 분석 결과, 입자 크기의 감소로 인하여 전극 내의 저항을 나타내는 R_ct 값이 현저하게 줄어들었다.분급하지 않은 Si 시료는 첫 사이클에서 2,869 mAh/g의 방전용량을 나타내었고, 100 사이클 후에는 85.7 mAh/g으로 방전용량이 감소하였다. Si를 24시간 분급한 시료의 경우에 초기에는 3,394 mAh/g의 용량을 보였으며, 100사이클 후에는 1,726 mAh/g의 용량을 유지하였다. 결과적으로 Si 입자의 크기가 감소할수록 방전용량이 증가하였으며, 사이클 수명도 증가하였다.

• Korean Chemical Engineering Research
• /
• 제58권1호
• /
• pp.84-91
• /
• 2020

염기성 폴리올 및 식용유 정제에 사용하는 합성 규산마그네슘의 효율성은 정제능력과 여과속도를 통해 평가되며, 규산마그네슘의 입도 및 표면적에 따라 영향을 받는다. 본 연구에서는 합성변수인 반응온도, 주입속도, 주입순서(Si, Mg), Mg/Si의 반응몰비가 규산마그네슘의 입도에 미치는 영향을 조사하였다. 합성된 규산마그네슘은 합성공정, 분쇄공정, 정제공정으로 비교 분석되었다. 합성공정에서 반응 온도와 주입 속도는 규산마그네슘의 평균입도 변화에 영향을 주지않는 반면, Mg/Si의 반응몰비와 주입 순서는 평균입도 변화에 주된 요인으로 작용하였다. 합성 후 규산마그네슘의 평균입도는 반응몰비가 0.125에서 0.500로 증가할 때 Mg 주입 시 약 54.4 ㎛에서 63.1 ㎛로 약 8.7 ㎛ 증가하였고, Si 주입 시 47.3 ㎛에서 52.1 ㎛로 약 4.8 ㎛ 증가하였다. 주입 순서 별 평균입도를 비교해보면 Mg 주입 시 59.1 ㎛, Si 주입 시 48.4 ㎛로 약 10.7 ㎛의 평균입도 차이를 보였으며 Mg을 주입하는 조건에서 약 2배 빠른 수세여과속도가 관찰되었다. 즉, 입도가 증가함에 따라 여과 시간이 단축되고 수세여과속도 증가로 생산성 향상에 기여할 수 있었다. 여과 후 분리된 cake형태의 규산마그네슘은 건조과정을 통해 단단한 고형체가 되고 분쇄공정을 통해 분말형태의 흡착제로 사용된다. 건조된 규산마그네슘의 물리적 강도가 감소함에 따라 분말의 평균입도가 감소하고, 이 강도는 반응몰비에 영향을 받는 것을 확인하였다. Mg주입 시 Mg/Si의 반응몰비가 증가함에 따라 규산마그네슘의 물리적 강도가 감소하여 분쇄 후 평균입도가 합성 후 평균입도에 비해 약 40% 감소하는 것을 관찰하였다. 이러한 강도감소는 평균입도 감소와 분쇄 후 미분량의 증가로 정제능력의 향상을 가져왔지만 정제여과속도 감소를 가져왔다. Mg 주입 시 반응몰비가 0.125에서 0.5로 증가할 동안 정제능력은 약 1.3 배가 증가하였으나 정제여과속도는 약 1.5 배가 감소하였다. 따라서 규산마그네슘의 생산성 향상을 위해서는 Mg/Si의 반응몰비를 증가시켜야 하지만, 폴리올의 정제여과속도를 증가시키기 위해선 반응몰비를 감소시켜야 한다. 규산마그네슘의 합성변수 중 주입순서와 Mg/Si의 반응몰비는 합성 후 평균입도와 분쇄 후 평균입도 및 미분량 변화에 영향을 주는 주요인자로 생산성 및 정제능력을 결정짓는 중요한 합성변수이다.

• Bulletin of the Korean Chemical Society
• /
• 제32권1호
• /
• pp.145-148
• /
• 2011

The thermal behavior of lithiated Si anodes has been investigated using differential scanning calorimetry (DSC). In particular, the effect of Si particle size on the thermal stability of a fully lithiated Si electrode was investigated. For DSC measurements, a lithiated Si anode was heated in a hermetically sealed high-pressure pan with a polyvinylidene fluoride (PVDF) binder and a 1 M $LiPF_6$ solution in an ethylene carbonate (EC)-diethyl carbonate (DEC) mixture. The thermal evolution around $140^{\circ}C$ increases with lithiation and with decreasing particle size; this phenomenon is attributed to the thermal decomposition of the solid electrolyte interface (SEI) film. Exothermic peaks, following a broad peak at around $140^{\circ}C$, shift to a lower temperature with a decrease in particle size, indicating that the thermal stability of the lithiated Si electrode strongly depends on the Si particle size.

• 한국세라믹학회지
• /
• 제50권1호
• /
• pp.31-36
• /
• 2013

${\beta}$-SiC powders were synthesized by a carbothermal reduction process using $SiO_2$-C precursors fabricated by a sol-gel process using phenol resin and TEOS as starting materials for carbon and Si sources, respectively. The C/Si molar ratio was selected as an important parameter for synthesizing SiC powders using a sol-gel process, and the effects of the C/Si molar ratio (1.4-3.0) on the particle size, particle size distribution, and yield of the synthesized ${\beta}$-SiC powders were investigated. It was found that (1) the particle size of the synthesized ${\beta}$-SiC powders decreased with an increase in the C/Si molar ratio in the $SiO_2$-C hybrid precursors, (2) the particle size distribution widened with an increase in the C/Si molar ratio, and (3) the yield of the ${\beta}$-SiC powder production increased with an increase in the C/Si molar ratio.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.237-239
• /
• 2002

The effect of particle sizes of the metal matrix composites containing 10 wt.%SiCp was investigated with using various tools. The results showed that tool life decreased considerably with increasing particle size and cutting speed. The wear resistance of TiC-coated tools was considerably higher than that of the other tools. It was observed that abrasive wear was the main responsible mechanism for wear of the tool thermal cracks were at high speed while a built-edge formation was also evident at lower speed.

• 한국주조공학회지
• /
• 제22권5호
• /
• pp.257-264
• /
• 2002

Effects of Ca content on the refinement of primary Si of Aluminum B390 alloy have been examined. Ca was found to have an effect on the refinement of primary Si particle. Primary Si particle size has been refined as Ca content of the melts decreased and cooling rate increased. A control of Ca content by the addition of $CuCl_2$ to the melt was the most efficient in the refinement of primary Si particles. The minimum size of primary Si particles in this study was $15.0\;{\mu}m$ when a residual content of Ca element in the alloy was 5ppm, Primary Si particle size was refined as primary Si crystallization temperature increased, which was attributed to the decrease of Ca content in the melts.

• 한국분말재료학회지
• /
• 제6권3호
• /
• pp.246-250
• /
• 1999

The effects of the ${\beta}-Si_3N_4$ starting particle size and $\alpha$/$\beta$ phase transformation during sintering process on the microstructure evolution of Yttrium $\alpha$-Sialon ceramics were investigated. As-received ${\beta}-Si_3N_4$ powder (mean particle size: 0.54$\mu$m) and classified ${\beta}-Si_3N_4$ powder(mean particle size: $0.26\mu{m}$) were used as starting powders. With decreasing the starting particle size, the growth of elongated grains was enhanced, which resulted in the whisker -like microstructure with elongated grains. These results were discussed in relation to the two-dimensional nucleation and growth theory. In the specimen heat treated at $1600^{\circ}C$ for 10h before sintering at $1950^{\circ}C$for 1h under 40atm(2-step sintering), the grain size was smaller than of the 1-step sintering at 195$0^{\circ}C$ for 1h. However, bimodal microstructure evolution were not not remarkable in both sample, which is ascribed to the $\alpha$-phase contents existing in ${\beta}-Si_3N_4$ starting powder.

• 한국산학기술학회논문지
• /
• 제14권4호
• /
• pp.1883-1889
• /
• 2013

Fe-Si계 합금은 우주탐사용으로 응용되고 있는 Si-Ge합금보다는 낮은 성능지수를 나타내지만 원료가 풍부하여 저가이고, 제조가 간단하며, $800^{\circ}C$까지 사용가능한 중고온용 열전발전재료이다. 본 연구에서는 고주파 진공유도로를 이용해서 제조한 p형 $FeSi_2$의 열전물성에 미치는 입자크기 및 첨가물 영향에 대해 조사하였다. 조성입자크기가 작을수록 소결밀도 증가와 함께 입자와 입자간의 연결성 향상에 의해 도전율이 증가하였다. Seebeck 계수는 600~800K에서 최고값을 나타내었고, 잔존하는 ${\varepsilon}$-FeSi 금속전도상에 의해 약간 감소하였다. $Fe_2O_3$ 및 $Fe_3O_4$를 첨가한 경우, 잔존 금속전도상 및 Si 결핍양 증가에 의해 도전율은 증가하였고 Seebeck 계수는 감소하였다. 반면에 $SiO_2$를 첨가한 경우에는 도전율과 Seebeck 계수 모두 상승하였다.

• 한국세라믹학회지
• /
• 제34권8호
• /
• pp.854-860
• /
• 1997

The tribological property of ceramics is very important for use in seal rings, pump parts, thread guides and mechanical seal, etc. In the present study, which RBSC/graphite composites were manufactured by adding graphite powders with different particle sizes to mixtures of SiC powder, metallic silicon, carbon black and alumina, effects on the tribological property of each RBSC/graphite composite was investigated in accordance with the particle size of the added graphite powder. The water absorption, the bending strength and the resistance for the friction and wear were measured, and the crystalline phase and the microstructure were respectively examined by using XRD and SEM. In case that the particle size of the graphite powder was fine(2${\mu}{\textrm}{m}$), the formation of $\beta$-SiC was accelerated, thereby making the increase of the bending strength and the decrease of the water absorption, but no improvement for the tribological properties. Furthermore, in case that the particle size of the graphite powder was some large(88~149${\mu}{\textrm}{m}$), the formation of $\beta$-SiC was not accelerated, to thereby make the decrease of the bending strength and the increase of the water absorption, but the improvement for the tribological property of only the composite having the graphite powder of 20 vol%. In addition, in case that the particle size distribution of the graphite powder was large (under 53 ${\mu}{\textrm}{m}$), there was no improvement for every properties. However, the composites, which the graphite powder with the particle size of 53~88 ${\mu}{\textrm}{m}$ was added in 10~15 vol%, had the most increased resistance for the friction and wear which show the worn out amount of 0.4~0.6$\times$10-3 $\textrm{cm}^2$, and the value of the bending strength is 380~520 kg/$\textrm{cm}^2$.