• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.163-168
• /
• 1997

Most of heteroepitaxial $\beta$-SiC thin films have been successfully grown on Si(100) adapting a carburizing process, by which a few atomic layers of substrate surface is chemically converted to very thin SiC layer using hydrocarbon gas sources. Using an organo-silicon precursor, bis-trimethylsilymethane (BTMSM, [$C_7H_{20}Si_2$]), heteropitaxial $\beta$-SiC thin films were successfully grown directy on Si substrate without a carburized buffer layer. The defect density of the $\beta$-SiC thin films deposited without a carburized layer was as low as that of $\beta$-SiC films deposited on carburized buffer layer. In addition, void density was also reduced by the formation of self-buffer layer using BTMSM instead of carburized buffer layer. It seems to be mainly due to the characteristic bonding structure of BTMSM, in which Si-C was bonded alternately and tetrahedrally (SiC$_4$).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.1
• /
• pp.36-41
• /
• 2000

We studied the exchange anisotropy of Ni-Fe/Co-Fe/Mn-Ir/Cu/buffer/Si multilayers using D.C magnetron sputtering technique. Generally, Ni-Fe/Mn-Ir/buffer(Cu)/Si multilayers cannot pin the ferromagnetic layer for the lower exchange biased field. We got $H_{ex}$ ex/ increased by two times, after using Cu/Ta as buffer layer to get larger grain size of Mn-Ir layer and inserting very thin Co-Fe layer between the Ni-Fe layer and the Mn-Ir layer to get improved grain-to-grain epitaxy relation at the interface between Ni-Fe layer and Mn-Ir layer. The variation of $H_{ex}$ by thickness of Mn-Ir layer in ferromagnete/Mn-Ir/buffer/Si multilayers is different to that in Mn-Ir/ferromagnete/buffer/Si multilayers, because the volume distribution of grain size of Mn-Ir layer and the exchange energy at the interface between the Mn-Ir and the ferromagnetic layers is different for stacking sequence.

• Journal of the Korean Ceramic Society
• /
• v.52 no.4
• /
• pp.290-293
• /
• 2015

The properties of the IZTO thin films on the glass were studied with a variation of the $SiO_2$ buffer layer thickness. $SiO_2$ buffer layers were deposited by plasma-enhanced chemical vapor deposition (PECVD) on the glass, and the In-Zn-Tin-Oxide (IZTO) thin films were deposited on the buffer layer by RF magnetron sputtering. All the IZTO thin films with the $SiO_2$ buffer layer are shown to be amorphous. Optimum $SiO_2$ buffer layer thickness was obtained through analyzing the structural, morphological, electrical, and optical properties of the IZTO thin films. As a result, the IZTO surface roughness is 0.273 nm with a sheet resistance of $25.32{\Omega}/sq$ and the average transmittance is 82.51% in the visible region, at a $SiO_2$ buffer layer thickness of 40 nm. The result indicates that the uniformity of surface and the properties of the IZTO thin film on the glass were improved by employing the $SiO_2$ buffer layer and the IZTO thin film can be applied well to the transparent conductive oxide for display devices.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.1
• /
• pp.21-25
• /
• 2009

Using an evaporation system, $SiO_2$ was deposited as a buffer layer between a PET substrate and a ITO layer and then ITO/$SiO_2$/PET layers were annealed for 1.5 hours at the temperature of $180^{\circ}C$. Adhesion and electro-optical properties of ITO films were studied with thickness variance of a $SiO_2$ buffer layer. As a result of introduction of the $SiO_2$ buffer layer, sheet resistance and resistivity increased and a ITO film with optimum sheet resistance ($529.3{\Omega}/square$) for an upper ITO film of resistive type touch panel could be obtained when $SiO_2$ of $50{\AA}$ was deposited. And it was found that ITO films with $SiO_2$ buffer layer have higher transmittance of $88{\sim}90%$ at 550 nm wavelength than ITO films with no buffer layers and the transmittance was enhanced as $SiO_2$ thickness increased from $50{\AA}$ to $100{\AA}$. Adhesion property of ITO films with $SiO_2$ buffer layers became better than ITO films with no buffer layers and this property was independent of $SiO_2$ thickness variance ($50{\sim}100{\AA}$). By depositing a $SiO_2$ buffer layer of $50{\AA}$ on the PET substrate and sputtering a ITO thin film on the layer, a ITO film with enhanced adhesion, electro-optical properties could be obtained.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.177-184
• /
• 1996

We adopted the $Pt/SiO_{2}/Si$ and the $Ir/SiO_{2}/Si$ substrates of which buffer layer is $PbTiO_{3}$ to improve electrode and interfacial properties of PZT thin film deposited by reactive sputtering method using metal target in this study. We got PZT thin film to have highly oriented(100) structure and good crystallinity using buffer layer in Pt bottom-electrode, though randomly oriented PZT thin film was obtained without buffer layer. Although great improvement of PZT phase formation on Ir bottom-electrode with buffer layer was not observed, we observed the increase of remennant polarization and the decrease of coercive field compared with properties of PZT thin films on the Pt bottom-electrode. So we got the results of the increase of dielectric constant using buffer layer on fabrication of PZT thin film and the better dielectric properties in PZT thin film using Ir bottom-electrode compared with that using Pt bottom-electrode.

• Journal of the Korean Magnetics Society
• /
• v.12 no.4
• /
• pp.132-136
• /
• 2002

Enhancement of crystallinity and exchange bias characteristics for NiFe/FeMn/NiFe trilayer with Si buffer layer fabricated by ion-beam deposition were examined. A Si buffer layer promoted (111) texture of fcc crystallities in the initial growth region of NiFe layer deposited on it. FeMn layers deposited on Si/NiFe bilayer exhibited excellent (111) crystal texture. The antiferromagnetic FeMn layer between top and bottom NiFe films with the buffer Si 50 ${\AA}$-thick induced a large exchange coupling field Hex with a different dependence. It was found that H$\sub$ex/ of the bottom and top NiFe films with Si buffer layer revealed large value of about 110 Oe and 300 Oe, respectively. In the comparison of two Ta and Si buffer layers, the NiFe/FeMn/NiFe trilayer with Si could possess larger exchange coupling field and higher crystallinity.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.336-340
• /
• 2012

Wide band gap p-type hydrogenated amorphous silicon oxide (a-SiO:H) buffer layer has been used at the interface of transparent conductive oxide (TCO) and hydrogenated amorphous silicon (a-Si:H) p-type layer of a p-i-n type a-Si:H solar cell. Introduction of 5 nm thick buffer layer improves in blue response of the cell along with 0.5% enhancement of photovoltaic conversion efficiency (η). The cells with buffer layer show higher open circuit voltage (Voc), fill factor (FF), short circuit current density (Jsc) and improved blue response with respect to the cell without buffer layer.

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.381-387
• /
• 2000

Si3N4/stainless steel 316 joints with Ni buffer layer were fabricated by direct active brazing method (DIB) using Ag-Cu-Ti brazing alloy only and double brazing method (DOB) using Ag-Cu brazing alloy with Si3N4 pretreated with Ag-Cu-Ti brazing alloy. For the joint brazed by DIB method, Ti was segregated at the Si3N4/brazing alloy interface, but was not enough to form a stable joint interface. In addition, large amounts of Ni-Ti inter-metallic compounds were formed in tehbrazing alloy near the joint interface, which could deplete the contents of Ti involved in the interfacial reaction. However, for the joint brazed by DOB method, segregation of Ti at the joint interface were enough to enhance the formation of stable interfacial reaction products such as TiN and Ti-Si-Ni-N-(Cu) multicompounds, which restricted the formation of Ni-Tio inter-metallic compounds in the brazing alloy during brazing with Ni buffer layer. Fracture strength of Si3N4/S.S 316 joints with Ni buffer layer was much improved by using DOB method rather than DIB method. It could be deduced that the differences of fracture strength of the joint with Ni buffer layer depending on brazing process adapted were directly affected by the formation of stable joint interface and the change in microstructure of the brazing alloy near the joint interface. It was found that fracture strength of Si3N4/S.S 316 joints with Ni buffer layer was gradually reduced as the thickness of interface. It was found that fracture strength of Si3N4/S.S 316 joints with Ni buffer layer was gradually reduced as the thickness of Ni buffer layer in the joint was increased from 0.1 mm to 10 mm. It seems to due to the increased residual stress in the joint as the thickness of Ni buffer layer is increased. The maximum fracture strength of Si3N4/S.S 316 joints with Ni buffer layer was 386 MPa, and the fracture of joint was originated at Si3N4/brazing alloy joint interface and propagated into Si3N4 matrix.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.5
• /
• pp.380-386
• /
• 1991

Hydrogen plasma-assisted epitaxial(PAE) growth of GaAs/Si and GaAs/Ge/Si with Ge buffer layer has been investigated. By means of photoluminescence, Nomarski microscopu, and $\alpha$-step, it could be known that GaAs on Si with Ge buffer layer has better crystalline quality than GaAs on Si without Ge buffer layer. The stoichiometry of GaAs layer on Si was confirmed by the depth profile of Auger electron spectroscope (AES). Also the native oxide(SiO$_2$) layer on Si substrate was plama-etched and the removal of the oxide layer was confirmed by AES. Photoluminescence peak wavelength of GaAs/Ge/Si with Ge buffer of 1\ulcorner thickness and GaAs growth rate of 160$\AA$/min was 8700$\AA$and FWHM was 12$\AA$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.64.2-64.2
• /
• 2011

a-Si 박막 태양전지는 a-Si:H을 유리 기판 사이에 주입해 만드는 태양전지로, 뛰어난 적용성과 경제성을 지녔으나 c-Si 태양전지에 비해 낮은 변환 효율을 보이는 단점이 있다. 변환 효율을 높이기 위한 연구 방법으로는 a-Si 박막 태양전지 단일cell 제작 시 high Bandgap을 가지는 p-layer를 사용함으로 높은 Voc와 Jsc의 향상에 기여할 수 있는데, 이 때 p-layer의 defect 증가와 activation energy 증가도 동시에 일어나 변환 효율의 증가폭을 감소시킨다. 이를 보완하기 위해 본 실험에서는 p-layer에 기존의 p-a-Si:H를 사용함과 동시에 high Bandgap의 buffer layer를 p-layer와 i-layer 사이에 삽입함으로써 그 장점을 유지하고 높은 defect과 낮은 activation energy의 영향을 최소화하였다. ASA 시뮬레이션을 통해 a-Si:H보다 high Bandgap을 가지는 a-SiOx 박막을 사용하여 p-type buffer layer의 두께를 2nm, Bandgap 2.0eV, activation energy를 0.55eV로 설정하고, i-type buffer layer의 두께를 2nm, Bandgap 1.8eV로 설정하여 삽입하였을 때 박막 태양전지의 변환 효율 10.74%를 달성할 수 있었다. (Voc=904mV, Jsc=$17.48mA/cm^2$, FF=67.97).