• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.741-745
• /
• 2002

Yttria-stabilized zirconia(YSZ) nanopowders were prepared by sol-gel method using zirconium-n-butoxide(ZNB) and yttrium nitrate as precursors. In addition, the effect of water content added during the hydrolysis reaction of ZNB was investigated on the phase composition and pore structure of the product powders. The phase composition of YSZ nanopowders with calcination temperatures showed the same trend, irrespective of $H_2O$ amounts added during the hydrolysis reaction of ZNB. All powders dried at $100^{\circ}C$ were amorphous and transformed to cubic phase at $400^{\circ}C$, which converted to tetragonal phase at $1,000^{\circ}C$. Monoclinic phase also appeared at $1,000^{\circ}C$. The powders showed the mixture of tetragonal and monoclinic phases from $1,000^{\circ}C$ to $1,400^{\circ}C$. The pore size distributions of the dried powders prepared with small amounts of water(less than or equal to $H_2O/ZNB=20$) showed mesopores, while those prepared with large amounts of water(greater than or equal to $H_2O/ZNB=50$) exhibited micropores.

• Journal of the Korean Magnetics Society
• /
• v.17 no.5
• /
• pp.198-204
• /
• 2007

The effects of annealing temperature on electromagnetic wave absorption characteristics in $Fe_{73.5}Cu_1Nb_3Si_{15.5}B_7$ (at%) alloy flakes/polymer composite sheets available for quasi-microwave band have been investigated. The composite sheet including the magnetic flakes annealed at $425{\sim}475^{\circ}C$ for 1 h exhibited highest power loss in the GHz frequency range as compared with the sheets composed of the alloy flakes annealed at higher temperature than $475^{\circ}C$ or in as-milled state. Moreover the imaginary part of complex permeability had largest value in the GHz frequency range for the sheets including the flakes annealed at $425{\sim}475^{\circ}C$. The large value of power loss of the sheets including the magnetic flakes annealed at $425{\sim}475^{\circ}C$ was attributed to the high imaginary part of the complex permeability. However, because of its large transmission parameter $S_{21}$, the composite sheet having the magnetic flakes annealed at $525^{\circ}C$ showed low power loss.

• Journal of Powder Materials
• /
• v.28 no.4
• /
• pp.293-300
• /
• 2021

We investigate the effect of phosphorous content on the microstructure and magnetic properties of Fe_83.2Si_5.33-0.33xB_10.67-0.67xP_xCu_0.8 (x = 1-4 at.%) nanocrystalline soft magnetic alloys. The simultaneous addition of Cu and P to nanocrystalline alloys reportedly decreases the nanocrystalline size significantly, to 10-20 nm. In the P-containing nanocrystalline alloy, P atoms are distributed in an amorphous residual matrix, which suppresses grain growth, increases permeability, and decreases coercivity. In this study, nanocrystalline ribbons with a composition of Fe_83.2Si_5.33-0.33xB_10.67-0.67xP_xCu_0.8 (x = 1-4 at.%) are fabricated by rapid quenching melt-spinning and thermal annealing. It is demonstrated that the addition of a small amount of P to the alloy improves the glass-forming ability and increases the resistance to undesirable Fe_x(B,P) crystallization. Among the alloys investigated in this work, an Fe_83.2Si₅B₁₀P₁Cu_0.8 nanocrystalline ribbon annealed at 460℃ exhibits excellent soft-magnetic properties including low coercivity, low core loss, and high saturation magnetization. The uniform nanocrystallization of the Fe_83.2Si₅B₁₀P₁Cu_0.8 alloy is confirmed by high-resolution transmission electron microscopy analysis.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.4
• /
• pp.274-279
• /
• 2008

In the perspective of saving energy in buildings, high performance of insulation and air tightness for improving the heating and the cooling efficiency has brought the positive effect in an economical view. However, these building energy saving technologies cause the lack of ventilation, which is the direct cause of increasing the indoor contaminants, and it is also very harmful to residents because they spend over 90% of their time in the indoor area. Therefore, the ventilation is important to keep indoor environment clean and it can also save energy consumption. In this study, a HEPA type breathing wall is designed as a passive ventilation system to collect airborne particles and to supply fresh outdoor air. To make fine porous structures, polymer nano fibers which were made by electro spinning method are used as a precursor. The nano fibers are coated with SiO2 nano particles and finally the HEPA type breathing wall is made by sintering in the electric furnace at $300\sim500^{\circ}C$. The pressure drops of nano ceramic structure are 8.2, 25.5 and 44.9 mmAq at the face velocity of 2.0, 5.9 and 8.8 cm/s, respectively. Also the water vapor permeability is $3.6g/m^2{\cdot}h{\cdot}mmHg$. In this research, the porous nano ceramic structures are obtained and the possibility for the usage of a material for HEPA type breathing wall can be obtained.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.25.1-25.1
• /
• 2009

Pattern 웨이퍼 상의 오염입자 제거는 반도체 산업의 주된 과제 중 하나이다. Pattern의 선폭이 좁아짐에 따라 Pattern에 손상을 가하지 않고 오염입자를 제거 하는 것은 더욱 어려워지고 있다. 그뿐만 아니라 기존 습식세정 공정에서의 화학액에 의한 환경오염 및 박막의 손실도 문제가 되기 시작했다. 이러한 문제를 해결하기 위해 기존 세정공정에서 화학액의 농도를 낮추고 Megasonic 등을 이용하여 세정력을 보완하는 방법들이 연구되고 있다. 하지만 습식세정의 경우 강한 화학작용으로 인한 표면 손상 및 물 반점의 문제는 여전히 이슈가 되고 있다. 이러한 단점을 극복하기 위하여 건식 세정법이 제시되고 있으며 이 중 레이저 충격파는 레이저를 집속시켜 발생된 충격파를 이용하여 입자를 제거하기 때문에 국부적인 세정이 가능하며 세정력 조절이 가능하여 손상이 세정을 할 수 있다. 그러나 Pattern의 구조에 의해 전되는 세정력의 차이가 발생하고 Trench 내부의 오염입자제거 문제점이 발생할 수 있다. 시편은 Si STI Pattern을 100 nm PSL Particle (Red Fluorescence, Duke Scientific, USA) 을 50ppm 농도로 희석시킨 IPA에 dipping 하여 오염시킨 후 N2 Gas를 이용하여 건조하여 준비하였다. 그리고 레이저 충격파 세정 시스템은 최대 에너지 1.8 J까지 가능한 레이저를 발생하는 1,064 nm Nd:YAG 레이저를 이용하여 실험하였다. 레이져 충격파 실험은 충격파와 시편사이의 거리, gap distance와 에너지를 변환하여 세정효율을 관찰하였다. 세정효율은 세정 전후의 입자 감소량을 현광현미경 (LV-150, Nikon, Japan)를 이용하여 측정하였다. 그 결과, Trench 내부의 오염입자의 경우 Trench 밖의 오염입자에 비해 세정효율이 떨어지는 것으로 나타났으나 시편과 레이저 초점과의 거리가 가까워짐에 따라 Trench 내부의 오염입자에 대한 세정 효율을 증가시킬 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.81-81
• /
• 2011

Sol-gel spin-coating법을 이용하여 ZnO 박막을 증착하였다. Sol 전구체 용액을 Si(100) 기판에 증착하고 전열처리(pre-heat treatment)하여 gel 상태의 ZnO 박막을 형성시킨 후 다른 속도로 냉각시켰다. Atomic force microscopy (AFM), X-ray diffraction (XRD), Raman, photoluminescence (PL)을 이용하여 냉각속도가 ZnO 박막의 구조적 및 광학적 특성에 미치는 영향을 분석하였다. 느린 속도($5^{\circ}C$/min)로 냉각시킨 ZnO 박막은 나노섬유질구조(nano-fibrous structure)를 나타내었고, 상온에서 바로 냉각시킨 ZnO 박막은 매우 매끄러운 표면(mirror-like surface)을 나타내었다. ZnO (100), ZnO (002), ZnO (101) 방향을 나타내는 회절피크가 관찰되었고, 냉각속도에 따른 ZnO 박막의 배향성을 알아보기 위하여 texture coefficient (TC)를 계산해 보았다. 상온에서 바로 냉각시킨 ZnO 박막(TC(002)=76.3%)이 느린 속도로 냉각시킨 박막(TC(002)=45.2%)보다 (002) 방향으로의 배향성이 우세하게 나타났으며, 잔류응력도 작았다. 뿐만 아니라 PL을 이용한 광학적 특성평가에서도 상온에서 바로 냉각시킨 ZnO 박막에서 더 강한 강도와 좁은 반치폭(full-width at halt-maximum)을 갖는 near-band-edge emission (NBE) 피크가 관찰되었다. 후열처리에 따른 구조적 및 광학적 특성 변화 또한 연구하였다.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.2
• /
• pp.174-181
• /
• 2007

In this study, $SiO_2/poly(ethylene-co-vinyl$ alcohol)(EVOH) hybrid coating materials with gas barrier property could be produced using sol-gel method. The biaxially oriented polypropylene (BOPP) substrate with surface pretreatment was coated with the prepared hybrid sols containing various inorganic silicate component by a spin coating method. Crystallization behavior of the hybrids was investigated in terms of analysis of X-ray diffraction and cooling thermogram from DSC experiment. From the morphological observation of the $SiO_2/EVOH$ hybrid gel, it was confirmed that there existed an optimum content of inorganic silicate precursor, Tetraethylorthosilicate (TEOS), to produce hybrid materials with dense microstructure, exhibiting uniformly dispersed silica particles with average size below 100 nm. When TEOS was added at below or above the optimum content, particle clusters with large domain were observed, resulting in phase separation. This morphological result was found to be in good agreement with that of oxygen permeability of the hybrid coated films. In the case of film coated with hybrid prepared from addition of 0.01 - 0.02mol of TEOS, a remarkable improvement in barrier property could be obtained, however, with the addition of TEOS more than 0.04 mol, the barrier property was dramatically reduced because of phase separation and micro-crack formation on the film surface.

• Korean Journal of Materials Research
• /
• v.14 no.8
• /
• pp.542-546
• /
• 2004

We report a new fabrication process for high performance triode type CNT field emitters and their superior electrical properties. The CNT-based triode-type field emitter structure was fabricated by the conventional semiconductor processes. The keys of the fabrication process are spin-on-glass coating and trim-and-leveling of the carbon nanotubes grown in trench structures by employing a chemical mechanical polishing process. They lead to strong adhesion and a uniform distance from the carbon nanotube tips to the electrode. The measured emission property of the arrays showed a remarkably uniform and high current density. The gate leakage current could be remarkably reduced by coating of thin $SiO_{2}$ insulating layer over the gate metal. The field enhancement factor(${\beta}$) and emission area(${\alpha}$) were calculated from the F-N plot. This process can be applicable to fabrication of high power CNT vacuum transistors with good electrical performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.248-248
• /
• 2009

Recently, the control of size, morphology and dimensionality in inorganic materials has been rapidly developed into a promising field in materials chemistry. 3D nanostructured flower-like ZnO architecture with different size and shapes have been simply synthesized via a hydrothermal process, using zinc acetate and ammonium hydroxide as reactants.[1] In this study, the Zno thin-films were deposited by RF magnetron sputtering in other to get high adhesion and uniformity of 3D nanostructured flower-like ZnO architecture on a $SiO_2$ substrate. The XRD patterns identified that the obtained the nanocrystallized ZnO architecture exhibited a wurtzite structure. SEM images illustrated that the flower-like ZnO bundles consisted of flower-like or chestnut bur, which were characterized by polycrystalline and [0001] preferential orientation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.437-437
• /
• 2013

3족 질화물은 우수한 광학 특성과 특히 3족 물질의 조성비 조절로 넓은 대역의 밴드갭 엔지니어링으로 발광다이오드의 물질로 각광 받고 있다. 이와 더불어 발광다이오드의 광추출효율을 향상시키기 위해 다양한 연구들이 활발히 이루어지고 있다. 그 연구 중 하나로 나노, 마이크로 사이즈의 막대와 같은 일차원적 구조와 최근 ITO를 활용한 투명 전극을 대체하여 전도도가 100배 정도 높은 금속을 이용한 옆면 접촉 전극을 도입한 것이 최근 발표되었다. 그러나 옆면 접촉 전극을 형성하기 위해서는 기존의 약 100 nm 정도의 두께의 p-형질화갈륨층은 공정 마진 등에 어려움이 있다. 따라서 기존에 비해 두꺼운 p-형 질화갈륨층이 필요하다. 보통 상용화된 유기 금속화학 증착법을 이용한 p-형 질화갈륨층은 도핑 물질인 Mg의 낮은 활성화와 성장 분위기 중 수소로 인해 양질의 것을 얻기 어렵고 이를 위해 성장 후 추가적인 활성화가 필요하다. 따라서 두꺼워진 p-형 질화갈륨층에 대해서도 기존의 성장 조건과 활성화 조건의 적합 여부와 이에 대한 연구가 필요하다. 따라서 본 연구에서는 양질의 p-형 질화갈륨을 얻기 위하여 성장 조건 및 성장 후 급속 열처리 온도, 시간에 대한 최적화와 약 630 nm 두께의 p-형 갈륨질화층을 가지는 발광다이오드에 대해 급속 열처리 조건에 대한 특성 연구를 실시한다.