• 한국환경보건학회지
• /
• 제36권2호
• /
• pp.108-117
• /
• 2010

In this study, ambient particulate matter ($PM_{2.5}$ and $PM_{10}$) levels were measured and their chemical and physical properties were characterized. Two sites in Gwangju were sampled once a month from December 2008 to November 2009. The annual mean concentrations of $PM_{2.5}$ and $PM_{10}$ were $26.9\;{\mu}g/m^3$ and $46.3\;{\mu}g/m^3$, respectively, in Nongseongdong and $26.1\;{\mu}g/m^3$ and $44.8\;{\mu}g/m^3$, respectively, in Duam-dong. $PM_{2.5}$ levels were 1.8 times higher than the USA Environmental Protection Agency (EPA) national ambient air quality standard for $PM_{2.5}$ ($15\;{\mu}g/m^3$). The average $PM_{2.5}/PM_{10}$ ratio of 0.58 suggested that $PM_{2.5}$ is a significant component of the ambient particle pollution. The order of concentration of metallic elements in $PM_{2.5}$ and $PM_{10}$ was Si > Al > Fe > Zn > Pb > Cu > Mn. Cd was not detected. The earth crustal enrichment factors for Cr, Cu, Pb and Zn in $PM_{2.5}$ were higher than those in $PM_{10}$. When the earth crustal enrichment factors for Cr, Cu, Pb and Zn were higher than 10, this suggested influence from anthropogenic sources. The soil contribution ratios for $PM_{2.5}$ and $PM_{10}$ were 11.3% and 16.4%, respectively, and were higher in the fall and winter. Anions (${SO_4}^{-2}$, ${NO_3}^-$, and $Cl^-$) comprise 28.7% of $PM_{2.5}$ and 21.4% of $PM_{10}$. The correlation coefficient of Zn-Fe, Mn-Cu, Fe-Cu and Fe-Mn in $PM_{2.5}$ was high in the sampling sites, and metallic elements were primarily from anthropogenic sources such as fuel combustion and vehicle emissions.

• Advances in concrete construction
• /
• 제10권5호
• /
• pp.403-416
• /
• 2020

This study investigated the effect of alkaline activators - NaOH_aq (NH) (NH: 0-16 M) and Na₂SiO_3aq (NS) (NS/NH: 0-3.5) in the synthesis of silico-manganese fume (SMF) and ground blast furnace slag (BFS) blended alkali-activated mortar (AASB). The use of individual activator was ineffective in producing AASB of sufficient fresh and hardened properties, compared to the synergy of both activators. This may be attributed to incomplete dissolution and condensation of oligomers required for gelation of the binder. An inverse relationship was noted among the fresh properties and the NH concentration or NS/NH ratio. This was influenced by the dissolution and condensation of silicate monomers under polymerization process. The maximum 28-day strength of ~45 MPa, setting time of 60 min and flow of 182 mm was obtained with the use of combined activators (10M-NH and NS/NH=2.5). The combined activators at NS/10M-NH=2.5 constituted SiO₂/Na₂O, H₂O/Na₂O and H₂O/SiO₂ molar ratio of 1.61, 17.33 and 10.77, respectively. This facilitated the formation of C-S-H, C/K-A-S-H and C-Mn-S-H in the framework together with an increase in the crystallinity due to more silicate re-organization within the aluminosilicate chain. On comparison of the high concentrated with mild alkali synthesized product, it revealed that the concentration of OH^- and Si monomers together with alkali metals influenced the dissolution of precursors and embedment of the constituent elements in the polymeric matrix. These factors eventually contributed to the microstructural densification of the mortar prepared with NS/10M-NH=2.5 thereby enhancing the compressive strength.

• 방사성폐기물학회지
• /
• 제6권4호
• /
• pp.297-306
• /
• 2008

본 연구는 방사성 폐기물 처분장의 지하수 화학 조건을 조절하는 수리지구화학 특성을 규명할 목적으로 수행되었다. 이를 위해 처분장 주변의 관측공 중 12개의 관측공이 선정되었으며, 이들 시료를 심도별로 총 46 지점에서 채취하였다. 또한 지표수 3점과 해수 1점의 시료도 채취하였다. 채취된 시료는 양/음이온 분석이 수행되었으며, 물과 용질의 기원을 규명할 추적자로서 산소-수소, 삼중수소, 탄소, 황 동위원소도 분석되었다. 산소-수소 동위원소 분석 결과 지표수와 지하수는 모두 강우 기원임을 보여주었으며, 삼중수소 농도는 깊이가 깊어짐에 따라 감소하고는 있으나 높은 삼중수소 농도는 최근에 충진된 물임을 나타내고 있었다. 양/음이온 분석 결과를 통한 수질 유형 분석에서는 연구 지역 지하수는 Ca-Na-$HCO_3$ 유형과 Na-Cl-$SO_4$ 유형이 대표적이었으며, 상관 분석 결과 이들 이온은 해염, 물-암석 반응의 영향을 받은 것으로 판단된다. 특히 연구 지역에서 Na 비율이 높은 이유는 양이온 교환 반응에 의해 이루어지고 있음을 보여 주었다. 연구 지역의 산화-환원 조건의 경우에는 심도가 깊어짐에 따라 낮은 DO와 Eh 값을 나타내어 환원 환경이 형성되었음을 나타내며, 높은 Fe와 Mn의 농도는 Fe와 Mn 산화물의 환원 반응이 산화-환원 조건을 조절하고 있음을 보여주었다.

• 한국재료학회지
• /
• 제19권11호
• /
• pp.601-606
• /
• 2009

$BiFeO_3$ (BFO) thin films were prepared on $Pt/TiO_2/Si$ substrate by r.f. magnetron sputtering. The effects of deposition pressure on electrical properties were investigated using measurement of dielectric properties, leakage current and polarization. When BFO targets were prepared, Fe atoms were substituted with Mn 0.05% to increase electrical resistivity of films. (Fe+Mn)/Bi ratio of BFO thin films increases with increasing partial pressure of $O_2$ gas. The deposited films showed the only BFO phase at 10 mTorr, the coexistence of BFO and $Bi_2O_3$ phase at 30-50 mTorr, and the only $Bi_2O_3$ phase at 70 mTorr. The crystallinity of BFO films was reduced due to the higher Bi contents and the decrease of surface mobility of atoms at high temperature. The porosity and surface roughness of films increased with the increase of the deposition pressure. The films deposited at high pressure showed low dielectric constant and high leakage current. The dielectric constant of films deposited at various deposition pressures was 84${\sim}$153 at 1 kHz. The leakage current density of the films deposited at 10${\sim}$70 mTorr was about $7{\times}10.6{\sim}1.5{\times}10.2A/cm^2$ at 100 kV/cm. The leakage current was found to be closely related to the morphology and composition of the BFO films. BFO films showed poor P-E hysteresis loops due to high leakage current.

• 한국자기학회지
• /
• 제13권2호
• /
• pp.47-52
• /
• 2003

DC 마그네트론 스파터법과 RLSA(Radial Line Slot Antenna)을 이용한 마이크로파 여기 프라즈마를 이용하여 Ta/Cu/Ta/NiFe/Cu/Mn$_{75}$Ir$_{25}$/ $Co_{70}$Fe$_{30}$/Al-oxide 구조의 접합을 제조한 후, contact-mode AM(Atomic Force Microscope)을 이용하여 Al 산화막의 국소전도 특성의 평가를 수행하였다. AFM 동시전류측정으로부터, 얻어지는 표면상과 전류상은 대응하지 않는다. 국소 전류-전압(I-V)의 측정 결과, 전류상은 절연층의 barrier height의 분포를 나타내고 있다는 것을 알았다.다.다.

• 한국환경과학회지
• /
• 제22권12호
• /
• pp.1661-1669
• /
• 2013

This study conducted a laboratory simulation using artificial and natural rainfall in order to investigate the runoff characteristics of livestock resources through the analysis of the surface runoff water and infiltration water by rainfall intensity and fertilization level. Cattle manure and pig liquid fertilizer was used as livestock resource. As a result of this study, it was observed that the surface runoff occurred over 32 mm/hr rainfall intensity, and flow rate of the surface runoff water and the runoff ratio of contaminant parameters from livestock resource was increased, as rainfall intensity was stronger. With doubled fertilization level, T-N increased in compost and the amount of $COD_{Mn}$ runoff also considerably increased in liquefied fertilizer. In the case of natural rainfall, the runoff ratio of T-P clearly increased in compost and the T-N of final surface runoff ratio in compost and liquefied fertilizer was ranged from 0.13047 to 0.13623 with stronger rainfall intensity.

• 청정기술
• /
• 제18권3호
• /
• pp.272-279
• /
• 2012

본 연구에서는 유기산과 여러 첨가제들을 사용하여 상수도의 정수장이나 배수지 벽면에 침적되어 있는 스케일 제거에 활용할 수 있는 친환경적인 세정제를 개발하고 현장 적용을 수행하였다. 정수장의 벽면의 스케일 분석결과 산화규소($SiO_2$), 산화알루미늄($Al_2O_3$), 산화철($Fe_2O_3$), 산화망간(MnO) 등 주로 금속산화물로 이루어져 있는 것을 알 수 있었다. 그리고 여러 유기산 중에서 말릭산(malic acid), 말론산(malonic acid), 시트릭산(citric acid)과 산화규소를 제외한 산화알루미늄, 산화철, 산화망간 등의 금속산화물에 비교적 좋은 용해력을 보여주었다. 이들 유기산들을 일정 무게비율로 배합하여 산화알루미늄, 산화철, 산화망간의 혼합 금속산화물의 용해력 실험 결과 여러 유기산 배합 비율 중 말릭산, 말론산, 시트릭산이 6 : 2 : 2 배합비율로 만든 10 wt% 유기산 혼합용액이 정수장 및 배수지의 스케일 제거효율이 약 29%로 가장 뛰어났음을 확인할 수 있었다. 이들 유기산 혼합용액에 비이온 계면활성제를 첨가하여 배합한 세정제 용액이 유기산 혼합용액만을 사용한 경우보다 더욱 높은 금속산화물 용해력을 가지는 것을 확인 할 수 있었다. 특히, 알콜에톡실레이트 계열의 LA-7 비이온계면활성제를 0.2% 첨가하는 경우 약 35%의 스케일 제거효율을 보여주었다. 그렇지만 유기산 혼합용액에 살균제를 첨가하는 경우 스케일 제거효율이 저하되었다. 이것은 계면활성제가 오염물의 유화분산 성질에 의해 스케일 제거력 향상에 도움을 주지만 살균제의 경우에는 살균제의 산화력에 의하여 스케일의 물에 대한 용해력을 떨어뜨려 스케일 제거에 방해를 하기 때문인 것으로 판단된다. 이러한 기초실험 결과를 바탕으로 유기산 혼합용액에 첨가제인 계면활성제, 살균제 등을 넣고 배합된 세정제를 사용하여 D시의 상수도 정수장 및 배수지의 스케일 세척시험에 성공적으로 적용시킬 수 있었다.

• Journal of Magnetics
• /
• 제9권1호
• /
• pp.13-16
• /
• 2004

Magnetic tunnel junctions (MTJs) comprising amorphous CoNbZr layers have been investigated. $Co_{85.5}Nb_8Zr_{6.5}$(in at. %) layers were employed to substitute the traditionally used Ta layers with an emphasis given on under-standing underlayer effect. The typical junction structure was $SiO_2/CoNbZr$ or Ta 2/CoFe 8/IrMn 7.5/CoFe 3/Al 1.6 + oxidation/CoFe 3/CoNbZr or Ta 2 (nm). For both as-deposited state and after annealing, the CoNbZr-underlayered structure showed superior surface smoothness up to the tunnel barrier than Ta-underlayerd one (rms roughness of 0.16 vs. 0.34 nm). CoNbZr-based MTJs was proven beneficial for increasing thermal stability and increasing $V_h$ (the bias voltage where MR ratio becomes half) characteristics than Ta-based MTJs. This is because the CoNbZr-based junctions offer smoother interface structure than the Ta-based one.

• Journal of Welding and Joining
• /
• 제30권5호
• /
• pp.40-45
• /
• 2012

Nowadays in Republic of Korea, whole amount of the thermite welding powder for rail joinning is dependent on import. However the demand of the thermite welding powder would be enlarge because some constructing high-speed train and city metro projects are currently in progress. In addition this is the main reason why we should develop the thermite welding powder, domestically. This study is focused on utilizing the recyclable materials like Al powders from cans and iron oxide scales from wire rods as the main components of the thermite welding powder. By minimizing Al content in weld zone by controlling the mixing ratio of the Al powder in the thermite welding powder, the excessive dissolution of the Si and Mn components came from the Al powders could be controled. The tensile strength of welding zone in welded rail was 740 MPa, with that the developed thermite welding powder.

• Journal of Magnetics
• /
• 제7권4호
• /
• pp.160-164
• /
• 2002

A new discovery of the super-giant magneto-impedance (SGMI) effect was found out in a LC-resonator consisted of a glass-coated amorphous $CO_{83.2}B_{3.3}Si_{5.9}Mn_{7.6}$ microwire. The measurement was carried out at high frequency range from 100 MHz up to 1 GHz of an ac-current flowing along the wire and at varying axial dcmagnetic field in its range of $\pm$120 Oe. The wires, about 16${\mu}m$ in diameter, were fabricated by a glass-coated melt spinning technique. The shape of the impedance curves plotted vs. a dc-field is changing dramatically with the frequency. The phase angle was also strongly dependent on this field. The external dc-magnetic field changes the circumferential permeability as well as the penetration depth, both in turn change the impedance of the sample. The drastic increments of SGMI at high frequency can be understood in terms of the LC-resonance phenomena. The sudden change of the phase angle, as large as $180^{\circ}$ evidenced the occurrence of the resonance at a given intensity of the external dc-field. The maximum ratio of SGMI reached in the experiment by precise tuning frequency equals 450,000％ at the frequency of around 551.9075 MHz.