• Electrical & Electronic Materials
• /
• v.7 no.2
• /
• pp.107-116
• /
• 1994

In the manufacturing of VLSI circuits, variations of device characteristics due to the slight differences in process parameters drastically aggravate the performances of fabricated devices. Therefore, it is very important to establish optimal process conditions in order to minimize deviations of device characteristics. In this paper, we used one-dimensional process simulator, SUPREM-II, and two dimensional device simulator, MINIMOS 4.0 in order to extract optimal process parameter which can minimize changes of the device characteristics caused by process parameter variation in the case of short channel nMOSFET and pMOSFET device. From this simulation, we have derived the dependence relations between process parameters and device characteristics. Here, we have suggested a method to extract process parameters from design trend curve(DTC) obtained by these dependence relations. And we have discussed short channel effects and device limitations by scaling down MOSFET dimensions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.30-33
• /
• 1992

This thesis was investigated on ion-induced characteristics in a-$Se_{75}Ge_{25}$ positive and negative resists for focused-ion-beam microlithogaphy. The exposed a-$Se_{75}Ge_{25}$ inorganic thin film shows an increase in optical absorption after exposure to~$10_{16}$ dose of Ga+. The observed shift in the absorption edge toward longer wavelengths is consistent with that in films exposed to band-gap photons(~$10^{21}$photons/cm2). This result may be related with microstructural rearrangements with in the short range of SeGe network. Due to changes in the short range order, the chemical bonding may be affected, which results in increased chemical dissolution in ion-induced film. Also, this resist exhibits good thermal stability because of its high Tg(~$220^{\circ}C$). When focused ion beams are used for direct exposure of resist over a substrate, unwanted implantation of the substrate may be an issue. A possible way to avoid this is to match the thickness of the resist to the range of ions in the resist. Thin aspect is currently under investigation.

• 전기의세계
• /
• v.13 no.3
• /
• pp.13-20
• /
• 1964

The measurements of X-ray and Gamma-ray Dose Rate have been successfully made by measuring the short circuit current of the Silicon P-N Junction Diode being irradiated. The short circuit current flows when a silicon P-N Junction Diode is irradiated by X-ray of Gammaray radiations due to photovoltaic effect. A brief analysis is given in order to verify the proportionality of a short circuit current to the Dose Rate. Using this method, measurements of X-ray Dose Rate were carried out in the range of 0.05-1600 r/m successfully. The calibration was made by comparing with Victoreen condenser r-meter. Some advantages in this Dose Rate meter over a condenser r-meter were found. One can measure a continous variation of X-ray Dose Rate with this rate meter at the control console of X-ray device.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.21 no.2
• /
• pp.63-71
• /
• 2015

Background: The purpose of the study, using the ICF Tool in the process of rehabilitation of artificial joint replacement surgery of the hip joint, goal setting and understanding of the problem, through the process of creating intervention strategies, useful clinical practical course for rehabilitation I try to present the data. Methods: Fracture was the left total hip replacement (THR) surgery due to women of 76 years old. I proceed in order screening, evaluation, diagnosis, prognosis, treatment planning and intervention, re-screening. Needs of the patient was walking short distances for using the toilet. In order to improve was carried out arbitration, after you have created a list of issues that limit the ability to walk short distances. Results: It was revealed improved results in self-paced walk test (SPWT) and Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) was used to examine whether the goals. In addition, MMT VAS, DGI, and TUG is a detailed goal was improved. Conclusions: It can be shown objectively the results of interventions performed for the purpose of solving the problem which is grasped through clinical Practical course for short-range walking ability enhance patient THR. I considered practical clinical course using the ICF Tool would be useful.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.2
• /
• pp.231-236
• /
• 2020

In today's society, the majority of people use smartphones, and mobile ordering and payment systems for their convenience are gaining their attention. The mobile payment market is on the rise, with over 71% of the market that is already formed in China. Many mobile payment markets are growing in Korea, which is a system that is provided only in large franchises. In this paper, we propose a mobile ordering and payment system using short-range wireless communication technology that can be easily used not only in franchises but also in the small businesses, and for the convenience of users in modern society to make a system that enables ordering and payment through mobile to communicate between the devices developed by short range wireless communication technology, smartphone and the main server.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.3
• /
• pp.690-696
• /
• 2013

This study, which is conducted on two groups of skilled people and unskilled people, is purposed to analyze joint angle of lower extremity during short track speed skating in order to find out efficient body position and propose ideal training method. Short Track Speed Skating has a wide range of research areas, but their findings indicate a promising area for further research. Targeting 8 people who are skilled in short track speed skating and 8 people who are not skilled in it, this study analyzes three dimensional images using super-high speed camera to compare differences between these two groups of people. In this study, 6 sections of body positions including right foot push-off, right foot recovery, right foot basic position, left foot push-off, left foot recovery, and left foot basic position were analyzed using 8 super-high speed cameras of VICON. These body positions were analyzed in order to find out joint angles of the hip joint, the knee joint, and the ankle joint. In the section 4 of the inner and outer parts of the left hip angles showed significant difference, and most of the sections of knee joint angles also showed significant difference. In the section 1 and 2 of the plantar flexion, dorsiflexion of ankle joints showed significant difference(p<.001) It was found out that there were differences between groups of skilled people and unskilled people in terms of lower extremity's joint angles such as angles of the hip joint, the knee joint, and the ankle joint.

• Journal of Aquaculture
• /
• v.10 no.3
• /
• pp.273-279
• /
• 1997

Condition for fresh storage of tiger puffer in the liquid state were investigated in several experiments. When marine fish ringer solution and 1% NaCl were used as the diluent for the short-term preservation method, spermatozoa activity index (SAI) and survival rate showed the best result among the various diluents tested. The dilution rate for the shortterm preservation of spermatozoa was suitable between 3 and 5 times with the 1% NaCi diluent. The appropriate range of temperature for the short-term preservation showed between 0 and $5^{\circ}C$. In order to keep high SAI and survival rate of spermatozoa, antibiotic addition (800 ppm neomycin) could be suggested. These results indicated that the short-term preservation method could be employed in tiger puffer spermatozoa.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.1019-1029
• /
• 2006

The ballistic range has long been employed in a variety of engineering fields such as high-velocity impact engineering, projectile aerodynamics, creation of new materials, etc, since it can create an extremely high-pressure state in very short time. Of many different types of ballistic ranges developed to date, two-stage light gas gun is being employed most extensively. In the present study, a theoretical work has been made to develop a new type of ballistic range which can easily simulate a flying projectile. The present ballistic range consists of high-pressure tube, piston, pump tube, shock tube and launch tube. The effect of adding a shock tube in between the pump tube and launch tube is investigated. This improvement is identified as the reduction in pressures in the high pressure tube and pump tube while maintaining the projectile velocity. Equations of motions of piston and projectile are solved using Runge-Kutta methods. Dependence of projectile velocity on various design factors such as high pressure tube pressure, piston mass, projectile mass, area ratio of pump tube to launch tube and type of driver gas in the pump tube are also analyzed. Effect of various gas combinations is also investigated. Calculations show that projectile velocities of the order 8 km/sec could be achieved with the present ballistic range.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.9
• /
• pp.2167-2173
• /
• 2013

Recently, people are paying huge attention to problems caused by indoor air pollution. Also, the need for the system that monitors environmental information for indoor and warns a danger is growing increasingly. In this regard, we designed and implemented environment monitoring system for indoor. In this paper, we describe the system with hardware elements and it's communication method. In order to transfer the data from environment sensors, we use short-range wireless communication in smart phone. The proposed system is possible to know the indoor environment information in installed sensor node. If the risk is found, For the proposed system, there is an advantage that may be appropriate evacuation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.1
• /
• pp.107-112
• /
• 2015

This paper introduces an evolutionary nonlinear regression based compensation technique for the short-range prediction of wind speed using AWS(Automatic Weather Station) data. Development of an efficient MOS(Model Output Statistics) is necessary to correct systematic errors of the model, but a linear regression based MOS is hard to manage an irregular nature of weather prediction. In order to solve the problem, a nonlinear and symbolic regression method using GP(Genetic Programming) is suggested for a development of MOS wind forecast guidance. Also FCM(Fuzzy C-Means) clustering is adopted to mitigate bias of wind speed data. The purpose of this study is to evaluate the accuracy of the estimation by a GP based nonlinear MOS for 3 days prediction of wind speed in South Korean regions. This method is then compared to the UM model and has shown superior results. Data for 2007-2009, 2011 is used for training, and 2012 is used for testing.