• Journal of Welding and Joining
• /
• 제25권5호
• /
• pp.58-63
• /
• 2007

The relationship between GMA welding conditions and the bead shape of overlay weld was studied by using ${\Phi}1.6mm$ hypo-eutectic metal-cored wire designed for hardfacing against the severe metal-to-metal wear. As the welding voltage increased, the dilution also increased but the sudden drop of dilution was observed at $30{\sim}33V$. It was considered to be due to the decrease of penetration resulting from the change of transfer mode, from short circuit to spray. It was also found that the behavior of penetration with welding current was dependant on the transfer mode. The short circuit mode exerted the penetration to decrease while the spray mode did it to increase with increase of welding current. The former was considered to be responsible for the remarkable decrease in dilution at low welding voltage region. The change of transfer mode also had an effect on the behavior of bead width with welding current but it did not on the bead spreadability defined as W/H ratio. It was considered that the optimal welding conditions for multi-pass overlay welding could be obtained from the bead spreadability suitable for bead lapping and the dilution as low as possible in the spray transfer mode.

• 공업화학
• /
• 제21권2호
• /
• pp.137-141
• /
• 2010

4,7-Di-thiophen-2-yl-benzo(1,2,5)thiadiazole과 1,4-bis(dodecyloxy)-2,5-divinylbenzene을 Heck coupling 중합법을 이용하여 poly[4,7-Di-thiophen-2-yl-benzo(1,2,5)thiadiazole]-alt-1,4-bis(dodecyloxy)-2,5-divinylbenzene (PPVTBT) 공중합체를 합성하였다. 합성한 PPVTBT의 최대흡수파장과 band gap은 각각 550 nm와 1.74 eV이고 HOMO와 LUMO enegry level은 각각 -5.24 eV, -3.50 eV로 나타났다. 합성한 공중합체인 PPVTBT와 (6)-1-(3-(methoxycarbonyl)propyl)-{5}-1-phenyl[5,6]-$C_{61}$(PCBM)을 1 : 6의 중량비로 blend하여 제작한 소자의 효율은 AM 1.5 G, 1 sun 조건($100mA/cm^{2}$)에서 0.16%의 효율을 보였다. 그리고 소자의 Jsc (short circuit current), FF (fill factor)와 Voc (open circuit voltage)는 각각 $0.74mA/cm^{2}$, 31%, 0.71 V로 나타났다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.441-441
• /
• 2009

Dye-sensitized solar cells (DSSCs) have been widely investigated as a next-generation solar cell because of their simple fabrication process and low coats. The cells use a porous nanocrystalline TiO2 matrix coated with a sensitizer dye that acts as the light-harvesting element. The photo-exited dye injects electrons into the $TiO_2$ particles, and the oxide dye reacts with I- in the electrolyte in regenerative cycle that is completed by the reduction of $I_3^-$ at a platinum-coated counter electrode. Since $TiO_2$ porous film plays a key role in the enhancement of photoelectric conversion efficiency of DSSC, many scientists focus their researches on it. Especially, a high light-to-electricity conversion efficiency results from particle size and crystallographic phase, film porosity, surface structure, charge and surface area to volume ratio of porous $TiO_2$ electrodes, on which the dye can be sufficiently adsorbed. Effective treatment of the photoanode is important to improve DSSC performance. In this paper, to obtain properties of surface and dispersion as nitric acid treated $TiO_2$ photoelectrode was investigate. The photovoltaic characteristics of DSSCs based the electrode fabricated by nitric acid pre-treatment $TiO_2$ materials gave better performances on both of short circuit current density and open circuit voltage. We compare dispersion of $TiO_2$ nanoparticles before and after nitric acid treatment and measured Ti oxidized state from XPS. Low charge transfer resistance was obtained in nitric acid treated sample than that of untreated sample. The dye-sensitized solar cell based on the nitric acid treatment had open-circuit voltage of 0.71 V, a short-circuit current of 15.2 mAcm-2 and an energy conversion efficiency of 6.6 % under light intensity of $100\;mWcm^{-2}$. About 14 % increases in efficiency obtained when the $TiO_2$ electrode was treated by nitric acid.

• 조명전기설비학회논문지
• /
• 제21권10호
• /
• pp.46-51
• /
• 2007

본 논문에서는 두 코일의 직 병렬결합을 이용한 초전도 사고전류제한기의 사고전류제한 특성을 분석하였다. 구조는 병렬 또는 직렬로 연결된 두 코일과 두 코일 중 하나와 직렬 또는 병렬로 연결되는 초전도 소자로 구성된다. 동작원리는 사고전에는 초전도 소자는 초전도 상태에 있어 병렬 또는 직렬로 연결된 두 코일에 의해 발생되는 자속은 서로 상쇄되어 두 코일에 유기되는 전압이 제로를 유지하게 되지만 사고가 발생할 경우 초전도 소자의 저항이 발생되어 두 코일에서 발생되는 자속은 더 이상 상쇄되지 않게 된다. 따라서 두 코일에 전압이 유기되고 이에 따라 사고전류를 제한하게 된다. 단락실험을 통해 두 코일의 직 병렬결합에 따른 사고전류제한 특성을 분석하였으며 분석을 동해 사고전류제한기의 동작전류를 증가시킬 수 있음을 확인하였다.

• 한국통신학회논문지
• /
• 제24권6A호
• /
• pp.820-831
• /
• 1999

본 논문에서는 음성 및 데이터서비스를 위한 무선접속시스템에서 D-TDMA(Dynamic-Time Division Multiple Access)와 CDMA(Code Division Multiple Access) 프로토콜의 성능을 비교 분석하였다. D-TDMA 프로토콜에서 음성서비스는‘circuit mode’로 채널 사용 우선권을 부여하고 데이터서비스는 FCFS(First Come First Service) 형태의 동적 채널 할당 방식을 사용하였다. CDMA 프로토콜에서는 내부 셀과 외부 셀에 존재하는 다른 이동가입자들의 간섭잡음을 줄이기 위하여 음성검출 기법을 사용하고, 이 경우의 간선잡음전력을 분석하였다. 또한, 이 간섭잡음전력을 이용하여 실제 데이터의 BER(Bit Error Rate)를 구하고, 평균 데이터 길이와 평균 데이터 발생률의 변화에 따른 음성차단확률(음성패킷손실확률) 및 데이터전송 지연시간을 비교 분석하였다. 분석결과에 따르면 평균 데이터 길이가 짧을 경우, 데이터 발생률의 증감에 독립적으로 CDMA 프로토콜이 상대적으로 우수한 성능을 보였다. 그러나, 평균 데이터 길이가 길어질수록 데이터 전송 지연시간이 큰 폭으로 증가하는 CDMA 프로토콜보다 D-TDMA 프로토콜이 더 우수한 성능을 보였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권10호
• /
• pp.687-692
• /
• 1999

A new technique to measure low level capacitance variations of the gyroscope is proposed and verified by computer simulation. It is based on the new CV(capacitance-voltage) converter circuit biased by dc current source and the peak detector without low pass filter. The CV converter biased by dc current source provides good signal-to-noise ratio and this setup of the detection circuitry without low pass filter makes it possible to provide short settling time, that is, higher speed of measurement and wide operation range if only a few parameters are adjusted. The key parameters that affect the performance of the detection circuitry are illustrated and computer simulation results are presented. The demonstrated detection circuitry shows linear response from 10 fF to 130 fF at 10 kHz and shows good linearity.

• 조명전기설비학회논문지
• /
• 제14권6호
• /
• pp.12-17
• /
• 2000

IN induction heating system the high frequency operation allows a rapid response to current fluctuation in the inverter and result in improved welding quality. To work induction heating of nonferrous metals, a welding power supply is need high working frequency and high power. This paper is shown design technique for increasing working frequency in induction heating for welding coppers. A series-parallel resonate inverter consists of H-type bridges, each of whose arms is composed of a combination of two parallel IGBTs. Inverter operating with the fixed frequency is controlled by pulse width modulation (PWM). As switching adapted the Zero-Voltage Switching technique to reduce switching losses the system is high efficiency. The propose inverter has feature which is high efficiency for very wide load variations with a narrow range of duty cycle ratio control and load short circuit capability. Detailed experimental results obtained from a 48[V] output, 500[W] experimental inverter are presented to verify the concept.

• 방재기술
• /
• 통권30호
• /
• pp.46-54
• /
• 2001

According to the use of electric power increases, the fire which ignited by electrical causes increases too. In this thesis electrical fires which occurs in the country for the past ten years are analyzed and developed the technology to identify the electrical fire. The focus of study is method to identify the electrical fires. The causes of electrical fire, it is analyzed a short-circuit and a over current, which take the highest ratio compare with other causes. The rationalization of identification, an electrical operating status is continuous monitored and the status can be accessed, black-box for identification electrical fires. The results of the study are the causes of electrical fire are found out logically, and the developed black-box for identification fires.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.28-30
• /
• 2006

본 논문에서는 대용량 동기발전기 회전자 권선의 다양한 단락사고 유형에 따라 발생하는 공극자속 파형의 변형정도에 대한 민감도해석을 수행하였다. 우선 정밀 전자장 수치해석도구를 이용하여 발전기 회전자 권선의 단락사고 유형에 대한 과도상태 해석을 수행하여 공극자속 파형에 대한 기본 데이터를 수집하였다. 이를 바탕으로 정상상태의 공극자속 파형을 기준으로 각 단락사고 유형별로 발생하는 공극자속 파형에 대한 최대 전압차에 다구찌법을 적용하여 Signal to Nose(SN) ratio 및 Percentage Contribution(PC) 등을 분석함으로써 단락사고 유형에 따른 공극자속 파형의 변형정도를 정량화하였다. 따라서 본 연구결과는 향후 대용량 발전기 회전자 단락사고 진단 및 감시 시스템 구축에 관련한 분야에 중요한 기초데이터로 활용될 것으로 사료된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2470-2474
• /
• 1999

The main drawback of parallel type active power filters (APFs) is the large capacity required for harmonic compensation. This paper evaluates the APF capacity requirement for harmonic/reactive power compensation for thyristor converter load. Theoretically achievable maximum power factor under partial load is evaluated. it is shown that the APF capacity can be considerably reduced by deliberately limiting the peak current, while maintaining the filtering performance with an acceptable total harmonic current level. the minimum capacity requirement of APF with current limiting is evaluated as a function of the firing angle of thyristor converter and short circuit ratio(SCR).