Lakshmi, D. Shanthana;Saxena, Mayank;Ekambaram, Shivakarthik;Sivaraman, Bhalamurugan
Membrane and Water Treatment
/
v.12
no.1
/
pp.43-49
/
2021
The Commercial polymeric membranes like Polysulfone (PSF), Polyvinylidene difluoride (PVDF) and Polyacrylonitrile (PAN) which are an integral part of water purification investigation were chosen for the shockwave (SW) exposure experiment. These membranes were prepared by blending polymer (wt. %) / DMF (solvent) followed by phase-inversion casting technique. Shockwaves are generated by using Reddy Tube lab module (Table-top Shocktube) with range of pressure (1.5, 2.5 and 5 bar). Understanding the changes in membrane before and after shock wave treatment by parameters, i.e., pure water flux (PWF), rejection (%), porosity, surface roughness (AFM), morphology (SEM) and contact angle which can significantly affect the membrane's performance. Flux values PSf membranes shows increase, 465 (pristine) to 524 (1.5wt%) LMH at 50 Psi pressure and similar enhancement was observed at 100Psi (625 to 696 LMH). Porosity also shows improvement from 73.6% to 76.84% for 15wt% PSf membranes. It was observed that membranes made of polymers such as PAN and PSF (of high w/w %) exhibits some resistance against shockwaves impact and are stable compared to other membranes. Shockwave pressure of up to 1.5 bar was sufficient enough to change properties which are crucial for performance. Membranes exposed to a maximum pressure of 5 bar completely scratched the surface and with minimum pressure of 1.5bar is optimum enough to improve the water flux and other parameters. Initial results proved that SW may be suitable alternative route to minimize/control membrane fouling and improve efficiency.
Kim, Jangho;Mun, Do Young;Ji, Goangseup;Kim, Gyuseon
KSCE Journal of Civil and Environmental Engineering Research
/
v.28
no.5A
/
pp.747-756
/
2008
The purpose of this paper is to investigate the effect of the important parameters on the transfer length during the dynamic flame cutting of tendon experimentally. The considered parameters were strand diameter, concrete cover thickness, stirrup, debonding strand and release method. Ten pretensioned concete beam specimens were cast and tested. Time history curves for the axial strain of tendon were measured by electrical resistance strain gauges mounted on the strands. Experimental results indicated that large dynamic shock effects occurred near cut-end during the sudden release. The prestressing forces are dependent on the parameters above considered. The ratio of residual prestressing forces of 12.7 mm strands is greater than 15.2 mm strands. Using debonding strand and gradual release are more efficient for applying prestressing forces.
The Bacillus cereus group, also known as B. cereus sensu lato (B. cereus s.l.), is composed of various Bacillus species, some of which can cause diarrheal or emetic food poisoning. Several emerging highly heat-resistant Bacillus species have been identified, these include B. thermoamylovorans, B. sporothermodurans, and B. cytotoxicus NVH 391-98. Herein, we performed whole genome analysis of two thermotolerant Bacillus sp. isolates, Bacillus sp. B48 and Bacillus sp. B140, from an omelet with acacia leaves and fried rice, respectively. Phylogenomic analysis suggested that Bacillus sp. B48 and Bacillus sp. B140 are closely related to B. cereus and B. thuringiensis, respectively. Whole genome alignment of Bacillus sp. B48, Bacillus sp. B140, mesophilic strain B. cereus ATCC14579, and thermophilic strain B. cytotoxicus NVH 391-98 using the Mauve program revealed the presence of numerous homologous regions including genes responsible for heat shock in the dnaK gene cluster. However, the presence of a DUF4253 domain-containing protein was observed only in the genome of B. cereus ATCC14579 while the intracellular protease PfpI family was present only in the chromosome of B. cytotoxicus NVH 391-98. In addition, prophage Clp protease-like proteins were found in the genomes of both Bacillus sp. B48 and Bacillus sp. B140 but not in the genome of B. cereus ATCC14579. The genomic profiles of Bacillus sp. isolates were identified by using whole genome analysis especially those relating to heat-responsive gene clusters. The findings presented in this study lay the foundations for subsequent studies to reveal further insights into the molecular mechanisms of Bacillus species in terms of heat resistance mechanisms.
With the rapid growth of mobility technology, the industrial sector is demanding storage devices that can reliably process data from various equipment and sensors in vehicles. NAND flash memory is being utilized as a storage device in mobility environments because it has the advantages of low power and fast data processing speed as well as strong external shock resistance. However, flash memory is characterized by data corruption due to long-term exposure to high temperatures. Therefore, a dedicated system for temperature management is required in mobility environments where high temperature exposure due to weather or external heat sources such as solar radiation is frequent. This paper designs a dedicated temperature management system for managing storage device temperature in a mobility environment. The designed temperature management system is a hybrid of traditional air cooling and water cooling technologies. The cooling method is designed to operate adaptively according to the temperature of the storage device, and it is designed not to operate when the temperature step is low to improve energy efficiency. Finally, experiments were conducted to analyze the temperature difference between each cooling method and different heat dissipation materials, proving that the temperature management policy is effective in maintaining performance.
This study fabricated a low-voltage 10 circuit distribution board based on the KEMC (Korea Electrical Manufacturers Cooperative) 2102-610 standard and performed a characteristics assessment of the developed 10 circuit distribution board to secure product stability. The developed 10 circuit distribution board is designed to have the characteristics of insulation materials, as well as resistance to corrosion ultraviolet radiation and mechanical impact. The developed distribution board is fabricated to have an appropriate protection class of enclosure, electric shock prevention and protection circuits, switchgear and its components, internal electrical circuits and connectors, external conduct terminal, insulation characteristics, temperature rise test, heat resistance, etc. The developed 10 circuit distribution board consists of a single phase circuit and 3-phase circuits. It is possible to measure in real time the leakage current generated from the load distribution line by installing a sensor module at the load side of each of the branched switchgears. In addition, it is possible to increase a circuit according to the use and purpose of the load and to also manage and check the load in real time. Temperature rise tests were performed on the developed 10 circuit distribution board at 18 places including the inlet connection, main circuit and distribution circuit bus bars and bus bar supports, etc. The highest temperature of $65.3^{\circ}C$ was measured at the R-Phase of the connection of the MCCB power supply for the branch circuit bus bar and a temperature rise of $61.6^{\circ}C$ was measured at the T-Phase of the load side. When applying thermal stress to an MCCB for 6 hours at $180^{\circ}C$ using a heat resistant experimental device, it was found that the actuator lever was transformed and moved in the tripped state.
This study was carried out to determine the storage, cryotolerance, heat and drying resistance, when Lactobacillus acidophilus CT 01 isolated from preweaned piglet feces growing at suboptimal temperature. L. acidophilus CT 01 suboptimal temperature incubated for 48 hours had the slowest growth rate at 22℃ but the highest viable cell number after 36 hours at 22℃, with 1.3×10/sup 9/ CFU/mL. In case of 4 and 20℃ storage, the suboptimal temperature incubated groups had a viability higher than the control (p<0.01). The cryotolerance of suboptimal temperature incubated L. acidophilus CT 01 was a higher than the control (p<0.01). When L. acidophilus CT 01 was heat treated at 60℃ for 15 minutes and 30 minutes, the suboptimal temperature incubated L. acidophilus CT 01 at 22℃ had a viability higher more than the control (p<0.01). L. acidophilus CT 01 incubated suboptimal temperature was inoculated by 30% to the carrier, and dried at 50℃ for 12 hours had the highest viability in the suboptimal temperature incubated L. acidophilus CT 01 at 28℃.
Kang, Ji Eun;Seok, Joon Young;Yun, Ki Wook;Kang, Hyoung Jin;Choi, Eun Hwa;Park, Kyung Duk;Shin, Hee Young;Lee, Hoan Jong;Ahn, Hyo Seop
Pediatric Infection and Vaccine
/
v.19
no.3
/
pp.131-140
/
2012
Purpose : This study was performed to identify the etiologic agents and antimicrobial susceptibility patterns of organisms responsible for bloodstream infections in pediatric cancer patients for guidance in empiric antimicrobial therapy. Methods : A 5-year retrospective study of pediatric hemato-oncologic patients with bacteremia in Seoul National University Children's Hospital, from 2006 to 2010 was conducted. Results : A total of 246 pathogens were isolated, of which 63.4% (n=156) were gram-negative, bacteria 34.6% (n=85) were gram-positive bacteria, and 2.0% (n=5) were fungi. The most common pathogens were Klebsiella spp. (n=61, 24.8%) followed by Escherichia coli (n=31, 12.6%), coagulase-negative staphylococci (n=23, 9.3%), and Staphylococcus aureus (n=22, 8.9 %). Resistance rates of gram-positive bacteria to penicillin, oxacillin, and vancomycin were 85.7%, 65.9%, and 9.5%, respectively. Resistance rates of gram-negative bacteria to cefotaxime, piperacillin/tazobactam, imipenem, gentamicin, and amikacin were 37.2%, 17.1%, 6.2%, 32.2%, and 13.7%, respectively. Overall fatality rate was 12.7%. Gram-negative bacteremia was more often associated with shock (48.4% vs. 11.9%, P<0.01) and had higher fatality rate than gram-positive bacteremia (12.1% vs. 3.0%, P=0.03). Neutropenic patients were more often associated with shock than non-neutropenic patients (39.6 % vs. 22.0%, P=0.04). Conclusion : This study revealed that gram-negative bacteria were still dominant organisms of bloodstream infections in children with hemato-oncologic diseases, and patients with gram-negative bacteremia showed fatal course more frequently than those with gram-positive bacteremia.
Purpose : Nosocomial infection with Staphylococcus aureus, especially methicillin resistant S. aureus, has become a serious concern in the neonatal intensive care unit. The aim of this study is to investigate the virulence factors, and the relationship between the antibiotic resistance and the associated genes of Staphylococcus aureus isolated from nasal cavity of neonates. Methods : Fifty one isolates of S. aureus were obtained from nasal swab taken in 28 neonates in the NICU and nursery of Pusan National University Hospital between February and May, 2001. They were tested in regard to antibiotic susceptibility, coagulase test and typing, plasmid DNA profile, as well as reactivity to enterotoxin A-E(sea, seb, sec, sed, see) genes and toxic shock syndrome toxin-1(tst) gene by polymerase chain reaction(PCR). Associated genes such as mecA, mecR1, mecI, and femA were also determined by PCR. The origin of MRSA strains was assessed using DNA fingerprinting by arbitrarily-primed polymerase chain reaction(AP-PCR). Results : Twenty three(45.1%) and six(11.8%) isolates were resistant to oxacillin and vancomycin respectively. Multidrug resistance to three or more of the antibiotics tested was observed in 51.0% of the isolates. Forty two isolates were coagulase positive and twenty two isolates had mecA gene. Sixteen isolates had both mecA and femA genes and had type I-III plasmids. 64.7% of isolates carried sec gene, and 80.4% carried tst gene. DNA fingerprinting by AP-PCR for 12 MRSA strains showed 10 distinct patterns, suggesting different origins. Conclusion : We confirmed that the prevalence of nasal carriage of S. aureus and the incidence of antimicrobial-resistant S. aureus, especially vancomycin resistance, is very high in neonates who were admitted in NICU and nursery. It is possible that these pathogens are responsible for serious nosocomial infections in neonates. The need for improved surveillance and continuous control of pathogens is emphasized.
The objective of this study was to identify EXE (1 hr a day at 21 m/min for 5 day/wk, at 0 % grade for 6 wk) on myocardium glucose metabolic phenotypic proteins (AMPK-PGC-1${\alpha}$-GLUT-4) and HSP-60 protein expression after ischemia/reperfusion injury (IRI) in STZ-induced rats. EXE was performed using STZ-induced diabetic rats on a rodent treadmill (28 m/min, 1 hr/day, 5 day/wk for 6 wk). The results of this study suggest that i) serum insulin level was not changed among groups (p>l0.05). ii) the LVDP level increased significantly in the STZ-EXE-IRI group compared to the STZ-IRI group at 60 min (p<0.01), 70 min (p<0.05) and 80 min (p<0.05) after reperfusion, respectively, and iii) AMPK phosphorylation (p<0.01), PGC-1${\alpha}$ protein (p<0.001), GLUT-4 protein (p<0.001) and HSP-60 protein expressions (p<0.05) increased significantly in the STZ-EXE-IRI group compared to the STZ-IRI group. In conclusion, the findings of the present study reveal that EXE may provide therapeutic value to insulin dependent diabetic patients with peripheral insulin resistance and myocardium injury by improving glucose metabolic proteins (AMPK-PGC-1${\alpha}$-GLUT-4) and heat shock protein-60 (HSP-60), along with increasing LVDP levels and decreasing glucose levels. Therefore, EXE protects the STZ-induced diabetic myocardium injury against ischemia/ reperfusion injury.
Flash memory based storage has been used in various mobile systems and now is to be used in Laptop computers in the name of Solid State Disk. The Flash memory has not only merits in terms of weight, shock resistance, and power consumption but also limitations like erase-before-write property. To overcome these limitations, Flash memory based storage requires special address mapping software called FTL(Flash-memory Translation Layer), which often performs merge operation for block recycling. In order to reduce block recycling cost in NAND Flash memory based storage, we introduce another block recycling scheme which we call migration. As a result, the FTL can select either merge or migration depending on their costs for each block recycling. Experimental results with Postmark benchmark and embedded system workload show that this cost-based selection of migration/merge operation improves the performance of Flash memory based storage. Also, we present a solution of macroscopic optimal migration/merge sequence that minimizes a block recycling cost for each migration/merge combination period. Experimental results show that the performance of Flash memory based storage can be more improved by the macroscopic optimization than the simple cost-based selection.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.