• Journal of the Korean Society of Safety
• /
• v.29 no.4
• /
• pp.23-27
• /
• 2014

The use of electromagnetic energy and non-equilibrium plasma for enhancing ignition and combustion stability is receiving increased attention recently. The conventional technologies have adapted the electrical devices to make the electromagnetic field, which resulted in various safety issues such as high-maintenance, additional high-cost system, electric shock and explosion. Therefore, an electrodeless microwave technology has an advantage for economic and reliability compared with conventional one because of no oxidation. However, the application of microwave has been still limited because of lack of interaction mechanism between flame and microwave. In this study, an experiment was performed with jet diffusion flames induced by microwaves to clarify the effect of microwave on the combustion stability and pollutant emissions. The results show that microwave induced flames enhanced the flame stability and blowout limit because of abundance of radical pool. However, NOx emission was increased monotonically with microwave intensity except 0.2 kW, and soot emission was reduced at the post flame region.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_3
• /
• pp.1155-1163
• /
• 2022

This study proposes a technology to ensure the seismic stability of a 1,000 kW diesel engine-type emergency generator by applying a seismic isolated bed system. The technology allows the static analysis by making the first natural frequency of the installed entire emergency generator larger than the earthquake cutoff frequency of 33 Hz. First a three dimensional model for the generator was made with simplification for mode analysis. A new bed system with springs, shock absorbers, stoppers was then devised. Next, The mode analysis for the finite element model equipped by the bed system was performed. the 1^st natural frequency above 33 Hz, the seismic safety cutoff frequency, was calculated to be 152.92 Hz. Finally, based on the seismic stability theory, the von-Mises equivalent stresses derived by structural analysis under the Upset and Faulted conditions were 0.01603 Mpa, and 32.06 Mpa, respectively. so seismic stability was confirmed.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.6
• /
• pp.791-799
• /
• 2005

The phased isolation intra-clarifier ditch system used in this study is a simplified novel process enhancing simultaneous removal of biological nitrogen and phosphorus in municipal wastewater in terms of elimination of additional pre-anaerobic reactor, external clarifier, recycle of sludge, and nitrified effluent recirculation by employing intrachannel clarifier. Laboratory-scale phased isolation ditch system was used to assess the treatability on municipal wastewater. When the system was operated at the HRTs of 6~12hours, SRTs of 9~31days, and cycle times of 2~8hours, the system showed removals of BOD, TN, and TP as high as 88~97%, 70~84%, and 65~90%, respectively. The rainfall in Korea is generally concentrated in summer because of site-specific characteristics. Especially, the wet season has set in on June to August. In combined sewers, seasonal variations are primarily a function of the amount of stormwater that enters the system. In order to investigate the effect of hydraulic shock loading on system performance, the laboratory-scale system was operated at an HRT of 6hours (two times of influent flowrate) during two cycles (8hours). The system performance slightly decreased by increasing of influent flowrate and decreasing of system HRT. Nitrification efficiency and TN removal were slightly decreased by increasing of influent flowrate (decreasing of system HRT), whereas, the denitrification was not affected by hydraulic shock loading. However, the higher system performance could be achieved again after four cycles. Thus, the phased isolation technology for enhanced biological nutrient removal in medium- and small-scale wastewater treatment plants suffering fluctuation of influent quality and flowrate.

• Publications of The Korean Astronomical Society
• /
• v.27 no.3
• /
• pp.39-47
• /
• 2012

MIRIS, Multi-purpose Infra-Red Imaging System, is the main payload of STSAT-3 (Korea Science & Technology Satellite 3), which will be launched in the end of 2012 (the exact date to be determined) by a Russian Dnepr rocket. MIRIS consists of two camera systems, SOC (Space Observation Camera) and EOC (Earth Observation Camera). During a shock test for the flight model stability in the launching environment, some lenses of SOC EQM (Engineering Qualification Model) were broken. In order to resolve the lens failure, analyses for cause were performed with visual inspections for lenses and opto-mechanical parts. After modifications of SOC opto-mechanical parts, the shock test was performed again and passed. In this paper, we introduce the solution for lens safety and report the test results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.191-196
• /
• 2007

With the development of micro electronic circuits and optical equipment, the demand for developing smart munitions with the ability to autonomously search for and attack targets has increased. Since the electronic components within smart munitions are affected by high temperatures, pressure, and impulsive forces upon the combustion of gunpowder, stability and reliability need to be secured for them. Securing those stability and reliability requires soft recovery system which can decelerate smart munitions. A theoretical analysis of flow is performed for the secure recovery of bullets on the basis of Navier-Stokes equation for compressible fluids. The inner pressure on a pressure tube, the speeds of bullets, and the deceleration of munitions are calculated theoretically. Theoretical results are compared with the data from the experiment with soft recovery system set up at the laboratory.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1155-1165
• /
• 2000

Due to the irregularity of walking ground and the inaccuracy in trajectory control of a leg, the mechanical shock and slip on the ground can be caused in the landing and supporting legs of a walkin g robot, and the robot may lose walking stability. Especially in a jointed-leg type walking robot, those problems are much more severe than in the pantograph type since the leg-weight of the jointed-leg type walking robot is relatively heavier than that of the pantograph type in general. In order to secure the walking stability for the jointed-leg type quadrupedal robot under development in KIST(Korea Institute of Science and Technology), a balancing algorithm consisting of the leg compliance control and the body posture control is implemented in this paper, and the effectiveness of the algorithm is verified through experiments.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.3
• /
• pp.112-117
• /
• 2020

NAND flash memory is a non-volatile memory that retains stored data even without power supply. Internal memory used as a data storage device and solid-state drive (SSD) is used in portable devices such as smartphones and digital cameras. However, NAND flash memory carries the risk of electric shock, which can cause errors during read/write operations, so use error correction codes to ensure reliability. It efficiently recovers bad block information, which is a defect in NAND flash memory. BBT (Bad Block Table) is configured to manage data to increase stability, and as a result of experimenting with the error correction code algorithm, the bit error rate per page unit of 4Mbytes memory was on average 0ppm, and 100ppm without error correction code. Through the error correction code algorithm, data stability and reliability can be improved.

• The Journal of Korea Robotics Society
• /
• v.5 no.2
• /
• pp.135-142
• /
• 2010

Security robot has gradually developed and deployed in order to protect civilian's lives as well as fortune and subjugate the shortcomings of CCTV which lacks of mobility. We have developed a security robot for outdoor environment and the main purpose of the driving mechanism is to overcome the bumps or projections with high speed. The robot platform consists of 4 omnidirectional wheel-based driving mechanisms and suspension for each driving mechanism. In this paper, principal suspension parameters of outdoor security robot for overcoming obstacles with stability are studied and approximately optimized using Response Surface Methodology (RSM) since it is difficult to find the exact relationship between suspension parameters and the shock, which is significantly associated with stability of the robot, at the robot platform. Simulation using ADAMS is conducted for assessing the feasibility of optimized design parameters.

• Journal of Aerospace System Engineering
• /
• v.15 no.4
• /
• pp.40-46
• /
• 2021

At launch, satellites are exposed to various types of structural loads, such as quasi-static loads, sinusoidal vibrations, acoustic/random vibrations, and shocks. The launch environment test is aimed at verifying the structural stability of the test object against the launch environment. Various types of launch environments are simulated by simple vibration, acoustic, and shock tests considering possible test conditions in ground. However, the difference between the launch environment and the test environment is one of the causes of excessive testing. To prevent overtesting, a notching technique that adjusts the frequency range and the input load considering the design load is applied. For notching, specific procedures are established considering the satellite development concept, selected launch vehicle, higher system requirements, and test target level. In this study, the notching method, established procedure, and development of a notching toolkit for efficient testing are described.

• The Bulletin of The Korean Astronomical Society
• /
• v.45 no.1
• /
• pp.55.1-55.1
• /
• 2020

In an attempt to investigate the nonlinear dynamics such as shock, shear, and turbulence associated with ultra-relativistic jets, we develop a new relativistic hydrodynamics (RHD) code based on the weighted essentially non-oscillatory (WENO) scheme. It is a 5th-order accurate, finite-difference scheme, which has been widely used for solving hyperbolic systems of conservation equations. The code is parallelized with MPI and OpenMP. Through an extensive set of tests, the accuracy and efficiency of different WENO reconstructions, and different time discretizations are assessed. Different implementations of the equation of state (EOS) for relativistic fluid are incorporated, As the fiducial setup for simulations of ultra-relativistic jets, we adopt the EOS in Ryu et al. (2006) to treat arbitrary adiabatic index of relativistic fluid, the WENO-Z reconstructions to minimize numerical dissipation without loss of stability, and the strong stability preserving Runge-Kutta (SSPRK) method to achieve stable time stepping with large CFL numbers. In addition, the code includes a high-order flux averaging along the transverse directions for multi-dimensional problems, and the modified eigenvalues for the acoustic modes to effectively control the carbuncle instability. We find that the new code performs satisfactorily simulations of ultra-relativistic jets.