• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.546-550
• /
• 2008

Impulsive excitation on vehicles produces shock-type vibration on the seat, usually which has major frequencies and damping ratios dependent on the characteristics of the suspension, the tire, the seat cushion and so on. The response of single degree of freedom model to a half-sine force input was considered as simple shock-type vibration signal. The quasi-apparent-mass for fifteen subjects was obtained with the shock-type vibration generated on the rigid seat, so its nonlinearity was found over 6.3 Hz according to the difference of magnitude of the shocks.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.3
• /
• pp.223-228
• /
• 2010

The mount which is used in military airplane should be operated in various situations such as vibration, shock and temperature. The recent mounts cost a lot and take much time to replace when they broke down. That's why new mount was produced in domestic by reverse engineering and the product has been proved its performance through environment test regarding vibration and shock. According to simulation of dynamic characteristics on vibration and shock, the result turns out to be similar to the result of the environmental test with an error of within 10 percent. As a result this research, a draft of the military aviation mount designing program is arranged.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.3
• /
• pp.285-290
• /
• 2008

Pyrotechnic shock or pyroshock is characterized as a transient vibration phenomena which shows large acceleration and high frequency range up to 10kHz during the operation of separation devices where explosives are used. During the flight of a launch vehicle, pyro-shock is mainly generated at several events such as satellite separation, fairing separation and stage separation. In this paper, characteristics of pyroshock are introduced briefly, and PEEK washer shock absorber is applied for the reduction of pyroshock in the high frequency range. With some electronic devices, reduction characteristic of pyroshock using washer type shock absorber are studied. Random vibration tests are also performed for the verification of vibrational characteristics.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.11 s.116
• /
• pp.1108-1114
• /
• 2006

Underwater acoustic transducers can be exposed to a underwater explosive shock caused by various types of underwater weapon. So, a robust anti-shock design is required for transducers to endure the underwater explosive shock. To check the anti-shock characteristics of a transducer, underwater explosive shock test is needed. The conditions of underwater explosive shock test are set up referring to various oversea explosive shock test specifications, and the explosive shock pressure values are calculated according to those conditions. Transient analyses art: carried out for two kinds of underwater acoustic transducer model to verify the anti-shock characteristics. The applied model has robust anti-shock characteristics enough to endure the explosive shock up to 2300 psi. In the future, the transducer design should be certified through the fields test, and modified if needed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.761-765
• /
• 2001

Shock responses of the MIL-S-901D standard floating shock platform("SFSP") subject to underwater explosions(UNDEX) are analyzed by using the LS-DYNA/USA. For the analysis, surrounding fluids as well as the SFSP are included in a 3D FE model to consider the cavitation effects of the UNDEX shock wave. The calculated results are compared with the existing test results and it is confirmed that the analysis results predict accurately the shock behaviors of the SFSP.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.490-495
• /
• 2001

This paper deals with an analysis and countermeasure for improving the shock performance of laptop computers. The shock analysis is carried out by using the commercial program of LS-DYNA3D. Also the analysis is verified by the measurements from modal tests and shock tests. The available countermeasures are investigated theoretically and experimentally to find the effective methods of reducing the shock acceleration on hard disk driver during one side fall test. The hard disk drive is the most sensitive part in a laptop computer. This research shows the effects of the spring constant of rubber pad, the reinforcement of mechanical parts and the location of a hard disk driver, on the shock reduction.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.8 no.1
• /
• pp.23-26
• /
• 2002

This study was carried out to investigate vibration shock and dropping shock of refrigerator during physical distribution. The values of vibration shock were measured to be ${\sim}3G$ for up and down direction, ${\sim}0.8G$ for right and left direction and ${\sim}0.5G$ for back and forth direction on the national road. There was no damage during transport. From the results of dropping test by KS A 1026(General Rules of Performance Testing for Packaged Freights), relative equations were gained as follow : y = 0.12x + 7.63(where y is G-factor and x is Dropping height). The maximum values of dropping shock during materials handling were measured to be 11G. This shock value was corresponding to dropping shocks of dropping height 28.3cm by KS A 1026.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.389.2-389
• /
• 2002

Nonlinear aeroelastic characteristics of a missile control surface are investigated in this study. The wing model has freeplay structural nonlinearity at its pitch axis. Nonlinear aerodynamic flows with unsteady shock waves are also considered in high-speed flow region. To effectively consider a freeplay structural nonlinearity, the fictitious mass method (FMM) is applied to structural vibration analysis based on finite element method (FEM). (omitted)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.1111-1116
• /
• 2001

A transient T-F(time-frequency) signal processing technique is applied to a tilt drop and a linear shock test rigs for identification of shock characteristics of hard disk drive (HDD). The T-F technique essentially tracks the shock characteristics of pivot point response as well as head slap and lift-off phenomena. From the T-F analysis result, the shock characteristic in HDD is modeled by the two degree of freedom coupled-dynamic system, which consists of actuator arm and suspension. As shock designing tool, the maximax shock response spectrum is employed for prediction of shock performance. Finally, the shock control technique is tested with newly designed actuator arm and suspension. Experimental head slap test result shows that the shock performance is much higher with the new shockproof designed model than the current model

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.214-215
• /
• 2005

Naval equipments are installed and used for naval vessel with different environmental conditions comparing to the commercial vessel, for example, high engine power per ship displacement size, severe vibration and shock due to high running speed and explosion from naval gun's bombardment and underwater weapons. Therefore, those equipments must be installed on shipboard with small spaces, high ambient temperature around engine room and which are required be fabricated with high resistances of vibration, shock and heat resources. But in case of commercial vessel, the performances of their recent equipments naval have been improved continuously due to the technology development of domestic shipbuilding and shipboard equipment industries, together with the related fundamental industries i.e, metal, steel and electronic industries, to an international level since 1970. With these results, it became possible to unify the specifications of shipboard equipments for the commercial and military vessels(Dual-Use). In this study, vibration and shock test standards for the commercial and military vessels will be compared and reviewed technically.