• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2005.04a
• /
• pp.592-600
• /
• 2005

Ship have cutout inner bottom and girder and floor etc. Ship's structure is used much, and structure strength must be situated, but establish new concept when high stress interacts sometimes fatally the area. There is no big problem usually by aim of weight reduction, a person and change of freight, piping etc.. Because cutout's existence grow up in this place, and elastic buckling strength by load causes large effect in ultimate strength. Therefore, stiffened perforated plate considering buckling strength and ultimate strength is one of important design criteria which must examine when decide structural concept at initial design. Therefore, md, reasonable buckling strength about stiffened perforated plate need to ultimate strength limited design . Calculated ultimate strength varied several web height and cutout's dimension, and thickness in this investigated data. Used program(ANSYS) applied F.E.A code based on finite element method

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.3
• /
• pp.250-256
• /
• 2008

Generally the side plate materials of FRP ship are composed of glass fiber and unsaturated polyester resin composites(GFRP composites). In this study, the effect of applied load and sliding speed on friction and wear characteristics of these materials were investigated at ambient temperature by pin-on-disc friction test. The cumulative wear volume, friction coefficient and wear rate of these materials for SiC abrasive paper were determined experimentally. The cumulative wear volume showed a tendency to increase nonlinearly with increase of sliding distance and was dependent on applied load and sliding speed for these composites. The friction coefficient of GFRP composites was increased as applied load increased at same sliding speed in wear test. It was verified by SEM photograph of worn surface that major failure mechanisms were microfracture, deformation of resin, cutting and cracking.

• Journal of the Korean Institute of Navigation
• /
• v.12 no.2
• /
• pp.68-101
• /
• 1988

In spite of the widespread use of stiffend plates in ship structures, it is very difficult to analysis these directly. So, in conventional analysis of plate structures, above structures are used to be idealized as orthotropic plate or grillage structures. Lately, the development of large computers, it is able to apply the optimum techniques to structural design. In this paper, the double bottom structure of Bulk Carrier was idealized into flat grillage which is composed of intersecting beam stiffencers primarily loaded mormal to its surface. And strength analysis was carried out by using the finite element method based on displacement. And further, according to variation of floor space and double tobbon heightm, the optimum design was carrid out by using Hooke and Jeeves direct search method.

• Proceeding of EDISON Challenge
• /
• 2012.04a
• /
• pp.109-112
• /
• 2012

선박의 저항을 추정하는 일은 선박설계에 있어 가장 기본적인 작업이다. 그러나 선박의 크기는 매우 크기 때문에 일반적으로 모형선 실험을 통해 선박의 저항을 추정한다. 이 때, 모형선 실험은 Froude 수를 기준으로 수행하게 되는데 이 때문에 모형선과 실선의 Reynolds 수가 서로 다른 영역에 놓이게 된다. 따라서 모형선 실험에서 얻어진 데이터를 실선에 그대로 적용할 수 없기 때문에 모형선-실선 저항추정법을 사용하게 된다. 본 연구에서는 이러한 모형선-실선 저항추정법에 사용되고 있는 2 차원 외삽법을 살펴보고 이 기법에 사용되고 있는 ITTC 마찰저항곡선을 등가평판 주위의 유동장 해석결과와 비교하였으며 ITTC 마찰저항곡선에 대해 고찰하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.1
• /
• pp.103-118
• /
• 2018

When collision accident between ships or between ship and offshore platform occurs, a common phenomenon that occurs in structures is the plastic deformation accompanied by a large strain such as fracture. In this study, for the rational design against accidental limit state, the plastic material constants of steel plate which is heated by line heating and steel plate formed by cold bending procedure have been defined through the numerical simulation for the high speed tension test. The usefulness of the material constants included in Cowper-Symonds model and Johnson-Cook model and the assumption that strain rate can be neglected when strain rate is less than the intermediate speed are verified through free drop test as well as comparing with numerical results in several references. This paper ends with describing the future study.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.5 s.54
• /
• pp.39-47
• /
• 2003

A study of the structural strength evaluation on the doubler plate, considering various load cases that were subjected to in-plane and out of plane combined load, has been performed through the systematic evaluation process. In order to estimate the proper static strength of doubler plate for various load cases, elasto-plastic large deflection analysis is introduced, including the contact effect between main plate and doubler. The characteristics of stiffness and strength variation are discussed, based on the results. In order to compare the doubler structure with the original strength of main plate, without doubler, simple formulas for the evaluation of the equivalent flat plate thickness are derived for each load case, respectively, based on the additional series of analysis of flat plate structure. Using these derived equations, the thickness change of an equivalent flat plate is analyzed according to the variation of various design parameters of doubler platesome design guides are suggested in order to maintain the original strength of main plate without doubler reinforcement. Finally, correlation between derived equivalent flat plate formula and the developed buckling strength formulas are discovered, and these relations are formulated for the future development of simple strength evaluation formula of general doubler plate structure.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.1
• /
• pp.47-52
• /
• 1999

The influence of propeller revolution on measurement of fluctuating pressure is almost minimized in the KRISO cavitation tunnel and the measurement accuracy of fluctuating pressure acting on a flat plate due to a cavitating propeller is improved. The measurement data for Sydney Excess propeller is compared with the measurement results of other research institutes loading to the conclusion that KRISO data is so stable and reasonable. The fluctuating pressure data measured on a model ship and the prototype ship is compared with the data measured on the flat plate. The solid boundary factor, derived from a calculation based on a lifting surface theory, is applied to predict full scale pressure level from the experimental data on the flat plate, showing quite reasonable agreement with full scale data.

• Transactions of Materials Processing
• /
• v.17 no.1
• /
• pp.27-34
• /
• 2008

In order to manufacture a doubly curved sheet metal, the incremental roll forming process which adopts advantages such as the flexibility of the incremental forming process and continuous bending deformation of the roll forming process has been experimentally investigated. An experimental equipment was developed which was named as unit roll set (URS) consisting of two pairs of support rolls and an upper center roll. The upper roll equipped with the servo control unit is motor-driven and can be positioned in the vertical direction according to the user's commands. Four support rolls are idle, and they freely rotate only along the axis so as to transfer the plate more stably in the tangential direction of the rotation of the driving roll. In the process, the plate is deformed incrementally as deformation proceeds simultaneously in longitudinal and transverse directions. Through the experiments using URS, information regarding to forming schedules is found out to fabricate curved hull plates. This study demonstrates the further application of the incremental roll forming process in shipbuilding industries.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2011.09a
• /
• pp.101-105
• /
• 2011

In most shipbuilding company, cutting procedure is proceed by cutting machine which run by CNC(Computer Numerical Code) data. In our cutting process, all CNC data is created by our nesting post processor system automatically. Among them, in case that cutting piece in the remnant plate, our system creates only one piece CNC data. Because remnant plate is not typical shape, and ship designers don't know remnant plate shape and quantity. In can happen some merit and good point if we modify 1:1 piece NC data by shorten cutting path, reducing cutting time or re-arrangement piece. For modifying cutting data, outside workers have to call to ship designer or have to go to NC control room where control the CNC system and cutting machine. It makes stop work process, and it waste time. In this paper, we introduce a program that can modify and replace 1:1 NC data with continuous or common NC data automatically.

• Journal of Ocean Engineering and Technology
• /
• v.37 no.6
• /
• pp.266-272
• /
• 2023

The structure of a ship is completed by processing various steel plates and welding these plates. This butt welding of plates is defined as a seam in shipyards, and this study seeks to find a way to decrease costs by reducing the utilization of steel through effective seam arrangement. Seams were defined and classified according to purpose, and examples of "pieces" and "main plates" where seam creation had an economical saving effect were selected. For "pieces," the change in the weight of steel utilized depending on the presence or absence of a seam was calculated, and the resulting change in cost increase was presented. In the case of the "main plate," the quantity of seams does not change, but an example of cost variation due to the appropriate placement of seams is presented. Hence, a large difference was found in the costs of "pieces" depending on seam location. Thus, it was advantageous to create additional seams. For the "main plate," it was found that narrow-width and wide-width materials incur more costs. This study demonstrates that creating seams is economically advantageous but may not be preferred owing to the increased workload from a production perspective.