• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.150-151
• /
• 2015

In this study, the electromagnetic shielding performance of mortar with different metal fiber, as part of the development of a electromagnetic shielding construction material, was measured according to KS C 0304. The results showed that the amorphous steel fibers can shield electromagnetic effectively than the oter conventional steel fibers. The superior performance of the amorphous steel fiber may be attributed its plate shape geometry.

• Journal of radiological science and technology
• /
• v.32 no.3
• /
• pp.307-312
• /
• 2009

The purpose of our study was to determine the eyeradiation dose when performing routine multi-detector computed tomography (MDCT). We also evaluated dose reduction and the effect on image quality of using a bismuth eye shield when performing head MDCT. Examinations were performed with a 64MDCT scanner. To compare the shielded/unshielded lens dose, the examination was performed with and without bismuth shielding in anthropomorphic phantom. To determine the average lens radiation dose, we imaged an anthropomorphic phantom into which calibrated photoluminescence glass dosimeter (PLD) were placed to measure the dose to lens. The phantom was imaged using the same protocol. Radiation doses to the lens with and without the lensshielding were measured and compared using the Student t test. In the qualitative evaluation of the MDCT scans, all were considered to be of diagnostic quality. We did not see any differences in quality between the shielded and unshielded brain. The mean radiation doses to the eyewith the shield and to those without the shield were 21.54 versus 10.46 mGy, respectively. The lens shield enabled a 51.3% decrease in radiation dose to the lens. Bismuth in-plane shielding for routine eye and head MDCT decreased radiation dose to the lenswithout qualitative changes in image quality. The other radiosensitive superficial organs specifically must be protected with shielding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.821-822
• /
• 2012

• Composites Research
• /
• v.31 no.3
• /
• pp.83-87
• /
• 2018

An object in the Low Earth Orbit (LEO) is affected by many environmental conditions unlike earth's surface such as, Atomic oxygen (AO), Ultraviolet Radiation (UV), thermal cycling, High Vacuum and Micrometeoroids and Orbital Debris (MMOD) impacts. The effect of all these parameters have to be carefully considered when designing a space structure, as it could be very critical for a space mission. Polybenzimidazole (PBI) is a high performance thermoplastic polymer that could be a suitable material for space missions because of its excellent resistance to these environmental factors. A thin coating of PBI polymer on the carbon epoxy composite laminate (referred as CFRP) was found to improve the energy absorption capability of the laminate in event of a hypervelocity impact. However, the overall efficiency of the shield also depends on other factors like placement and orientation of the laminates, standoff distances and the number of shielding layers. This paper studies the effectiveness of using a PBI coating on the front bumper in a multi-shock shield design for enhanced hypervelocity impact resistance. A thin PBI coating of 43 micron was observed to improve the shielding efficiency of the CFRP laminate by 22.06% when exposed to LEO environment conditions in a simulation chamber. To study the effectiveness of PBI coating in a hypervelocity impact situation, experiments were conducted on the CFRP and the PBI coated CFRP laminates with projectile velocities between 2.2 to 3.2 km/s. It was observed that the mass loss of the CFRP laminates decreased 7% when coated by a thin layer of PBI. However, the study of mass loss and damage area on a witness plate showed CFRP case to have better shielding efficiency than PBI coated CFRP laminate case. Therefore, it is recommended that PBI coating on the front bumper is not so effective in improving the overall hypervelocity impact resistance of the space structure.

• Nuclear Engineering and Technology
• /
• v.49 no.7
• /
• pp.1563-1570
• /
• 2017

In order to perform dry interim storage and transportation of the spent-fuel assemblies of the Bushehr Nuclear Power Plant, dual-purpose casks can be utilized. The effectiveness of different neutron-shield materials for the dual-purpose cask was analyzed through a set of calculations carried out using the Monte Carlo N-Particle (MCNP) code. The dose rate for the dual-purpose cask utilizing the recently developed materials of $epoxy/clay/B_4C$ and $epoxy/clay/B_4C/carbon$ fiber was less than the allowable radiation level of 2 mSv/h at any point and 0.1 mSv/h at 2 m from the external surface of the cask. By utilization of $epoxy/clay/B_4C$ instead of an ethylene glycol/water mixture, the dose rates on the side surface of the cask due to neutron sources and consequent secondary gamma rays will be reduced by 17.5% and 10%, respectively. The overall dose rate in this case will be reduced by 11%.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.4
• /
• pp.59-63
• /
• 2019

To reduce the fault current below the current capacity of a circuit breaker, researches on HTS (High Temperature Superconductor) power cables with fault current limiting (FCL) function are increasing. An FCL HTS power cable transports current with low a impedance during normal operation. Yet, it limits the fault current by an increased inductive or resistive impedance of conducting layer when quench occurs at the FCL HTS power cable by the large fault current. An inductive type FCL HTS power cable uses increased inductive impendence caused by leakage magnetic flux outside the cable core when the quench occurs at a shield layer losing the magnetic shielding effect. Therefore, it has an advantage of less resistive heating than resistive type FCL HTS power cable and temperature increase is suppressed. This paper describes an ideal circuit model for the FCL HTS power cable to investigate the effectiveness of increased inductive impedance when quench occurs at the shield layer. Then, FEM analysis is presented with a simplified model cable composed of various iron yokes to investigate the effect of the shape of yoke on the generation of the inductive impedance.

• Journal of Aerospace System Engineering
• /
• v.16 no.6
• /
• pp.18-23
• /
• 2022

This paper examines the electromagnetic shielding structure of ultra-high frequency (UHF) RF modules used in aircraft. Advances in electrical and electronic technologies have increased the need for electronic equipment in aircraft. High-frequency wireless devices have become integrated circuits in the form of UHF integrated circuits to support a wide range of frequencies and miniaturisation. To ensure the functionality and performance of these integrated devices in aviation, shielding is necessary to prevent unexpected electromagnetic interference, which could be detrimental to aircraft safety. A shield structure was designed to protect the RF chipset from malfunctioning, and the shielding effectiveness was improved through the application of various geometric shapes.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.551-552
• /
• 2011

In this study new evaluation method of eddy currents in conductive shielding sheets are introduced. This method is based on the magnetic flux linkage in rectangular cells. According to this method the allocated amount of memory and the calculation time can be reduced. In this method calculation of magnetic field in any space can be performed by summing contributions of source currents and eddy currents in conductive shielding sheets. This method is applicable to the design of magnetic field-shield.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.4
• /
• pp.36-43
• /
• 2007

Dieless CNC forming is an innovative technology which can form various materials with complex shape by numerically controlled incremental forming process. In order to apply the technology to industrial parts, however, many problems such as spring-back, rising of material, and trimming difficulty must be solved. In this paper a new dieless CNC forming method to improve forming quality is proposed, which consists of how to modify its original shape in CAD and how to generate its CNC tool path in CAM. The effectiveness of the proposed procedures is tested with a brake dust shield of a vehicle. The results shows that the method proposed enhances the forming quality up to 48% compared to traditional method.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.80-83
• /
• 2002

A 3D shape optimization algorithm integrates the geometric parameterizationi 3D F.E. performance analysis, steepest descent method with design sensitivity and mesh relocation method. The design sensitivity of the surface nodal points is also systematically converted into that of the design variables for the application to parameterized optimization. The proposed algorithm is applied to the optimum design of tank shield model of transformer and the effectiveness is proved.