• 소성∙가공
• /
• 제17권6호
• /
• pp.401-406
• /
• 2008

The frictional behavior of stamping process is a function of interface parameters such as sheet and tool material, lubricant, surface roughness, contact pressure, sliding speed etc. Among these parameters the thing that can be controlled by a steel maker is the surface roughness of sheet. In this study, effects of surface roughness on the frictional behavior of steel sheet for automotive were investigated to find out the way to improve the frictional characteristics of steel sheet. The cold rolled steel sheets with various surface roughnesses were prepared for the test. The flat type friction test was conducted with different lubricant conditions. The surface roughness effect on frictional behavior depends on the viscosity of lubricant. The frictional characteristic of steel sheet was influenced by the amplitude of roughness as well as the shape of that.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.36-43
• /
• 1998

Surface roughness of cold rolled steel sheet as well as the coating technique itself is quite important in obtaining high image clarity of electronic products and car outer panels. Especially, surface characteristics of steel sheet have acquired increasing attention from the steel and automotive industries. While the influence of such characteristics on paintability formability and painted surface appearance is important in defining steel surface requirements for automotive industries. Therefore this paper is dedicated primarily to the issue of paint appearance and reviews for improvement of roughness and peak count about the surface of work roll for the actual temper mill. The conclusions were obtained as follows ; 1) Roughness and peak count about the surface of steel sheet is strongly affected by surface condition of work roll. 2) The electro-discharge textured roll has more uniform roughness distribution than shot blasted roll and it's painted appearance of steel sheet has more improvement than that of the shot blasted because it has more harmonic wave roughness, and the higher peak count of surface roughness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.546-551
• /
• 1997

In sheet metal forming, since the surface area of workpiece is apparently larger than the volume of it, the surface condition of the sheet metal is much varied. The formability of sheet metal is decided by the forming limit and the macroscopic suface defect as like fracture and wrinkle, and microscopic asponent, The factors affected in forming limit are stain herdening exponent, strain-rate scnsitivity exponent, anisotropic coefficient. The increasing of surface roughness is decresed the forming limit curve. It is known that the greater plastic deformation the more surface roughness by Kienzle, Osadaka. The purpose of this study is to investigate the influences of surface roughness in a uniaxial tension and the traperzoidal-shaped box drawing.

• 소성∙가공
• /
• 제11권4호
• /
• pp.349-354
• /
• 2002

In order to find the effect of lubricant viscosity, sheet surface roughness, tool geometry, and forming speed on the frictional characteristics in sheet metal forming, a sheet metal friction tester was designed and manufactured and friction test of various sheet were performed. Friction test results showed that as the lubricant viscosity becomes lower, the friction coefficient is higher. When surface roughness is extremely low or high, the friction coefficient is relatively high. The result also show that as the punch radius and punch speed becomes bigger, the friction coefficient is smaller. Using experimental results, the mathematical expression between friction coefficient and lubricant viscosity, surface roughness, punch comer radius, or punch speed is also described.

• 소성∙가공
• /
• 제22권4호
• /
• pp.223-228
• /
• 2013

The friction coefficients of advanced high strength steel sheets were experimentally determined. In the friction test, the pulling and holding forces acting on the sheet for various friction conditions, such as lubricant viscosity, pulling speed, blank holding pressure, sheet surface roughness, and hardness of the sheet were measured and the friction coefficient was calculated based on Coulomb's friction law. While the friction coefficient, generally, decreases as the value of friction factor increases, the factor associated with the sheet surface roughness shows U shape behavior for the friction coefficient. Furthermore, the relationship between friction coefficient and the wear volume, which was computed for the roughness of both sheet surfaces and the friction area, is linearly proportional.

• 소성∙가공
• /
• 제19권4호
• /
• pp.236-241
• /
• 2010

The frictional behavior of bare steel sheet highly depends on surface roughness. It was investigated that the change of surface roughness of bare steel sheet due to deformation for each forming mode. The flat type friction test was done to check the effect of surface roughness change on frictional characteristics of bare steel sheet. As increasing the deformation, the Ra value was increased at stretching forming mode and drawing forming mode, however the change of Pc showed different trends. The Pc was decreased as increasing stretch deformation but increased at compression deformation. At drawing forming mode, the friction coefficient was increased as deformation was increased after initial big drop with drawing oil. As deformation was increased, the friction coefficient was decreased with drawing oil at stretching forming mode. The results show that the deformation changes the surface roughness and frictional characteristics of steel sheet but the effect depends on the forming mode.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.24-27
• /
• 2001

Friction between the sheet and tools is one of the important factors affecting the sheet metal forming. Therefore, the clarification of the friction is essential to improve the formability of the sheet. In order to find the effect of material property and lubricant viscosity on the frictional characteristics, tensile test, surface roughness test and friction test are performed. The results showed that friction characteristics are mainly influenced by the surface roughness and lubricant viscosity. A mathematical model of the friction is developed for calculating friction coefficient in terms of surface roughness and lubricant viscosity. The validity and accuracy of the mathematical model of the friction are verified through the experiment and FEM analysis.

• Journal of Welding and Joining
• /
• 제26권2호
• /
• pp.75-84
• /
• 2008

With the development of surface roughness textured steel for automotive body-in-white assemble, one of key issues is to understand the role of the surface roughness in textured steel sheets. To investigate effect of surface roughness on weldability in prepared steels, electrode force was varied. Steel sheets (T-H) with high surface roughness ($Ra\;=\;1.94\;{\mu}m$) reduced electrode life. It was attributed to the higher contact resistance at the electrode-sheet interface in the presence of the high surface roughness. The increased electrode diameter decreased current density, therefore reducing weld electrode life due to small weld button size. When an increased electrode force was used, a significant increase in the electrode life was observed in welding of high surface roughness steel sheet. This study suggested that contact resistance at the electrode-sheet interface was the dominant factor, as compared to the sheet-sheet interface for determining electrode life in welding of surface roughness textured steel.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.68-75
• /
• 2008

This paper investigates the correlation between surface roughness and gloss of aluminium sheet painted waterborne paint. One customer criterion of automotive quality is the as-painted appearance of the final products. Especially, the current emphasis on control of surface roughness of sanded aluminium sheet has been prompted by the automotive industry's concern with the as-painted appearance. because the influence of such characteristics on paintability, and painted appearance is important in defining outer panel requirements for automobile. This paper is dedicated primarily to the issue of painted appearance and reviews for improvement of roughness. The conclusions are obtained as follows ; 1) Painted aluminium sheet appearance is strongly affected by surface roughness of base-metal and influenced by sand paper and sanding method. 2) The painted appearance of aluminium sheets was determined and related to surface roughness parameters, combination of sand paper.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.54-57
• /
• 2002

In order to find the effect of lubricant viscosity, sheet surface roughness, tool geometry, and forming speed on the frictional characteristics in sheet metal forming, a sheet metal friction tester was designed and manufactured and friction tests of various sheets were performed. Friction test results showed that as the lubricant viscosity becomes lower, the friction coefficient is higher. When surface roughness is extreme1y low or high, the friction coefficient is high. As punch comer radius and punch speed are bigger, the value of friction coefficient is smaller. The sensitivity of friction coefficient is mainly governed by lubricant viscosity and sheet surface roughness.