• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.656-665
• /
• 2010

Shear modulus has been recognized as one of the important soil properties in dynamic analysis of ground and can be calculated from in situ measurement of shear wave velocity. Field seismic tests are the most accurate but expensive methods to investigate dynamic ground characteristics. Due to that reason, empirical equations for estimating the shear wave velocity are widely used rather than conducting in-situ tests. The most common equations are based on the N value obtained in conjuctions with a standard penetration test. In this paper, the field datas of standard penetration test and suspension PS logging measured in 126 sites of Korea were summarized and the correlation equations between N value and shear wave velocity are suggested.

• Geomechanics and Engineering
• /
• v.25 no.3
• /
• pp.245-251
• /
• 2021

The present study investigated the ageing effect on compressibility, permeability and shear strength behavior of kaolin and bentonite samples in the presence of NaCl and CaCl₂ solutions. The compressibility, permeability and shear strength parameters were determined on the 60, 190, and 250 days cured samples. The results have shown that, the kaolin sample becomes more compressible in the presence Ca²⁺ ions with ageing. Generally, the normalized compression index values of bentonite samples increased at the end of 60 days and 250 days curing time periods. The normalized permeability value of kaolin decreased by ageing in the presence of Na⁺ ions almost twofold. The permeability values of bentonite increased both in NaCl and CaCl₂ solutions during ageing. In the presence of Na⁺ ions kaolin had higher max. shear stress value than Ca²⁺ ions. When the max. shear stress values of 0, 60 and 190 days samples were compared, it was seen that NaCl solution had no significant effect on the shear strength of kaolin sample. However, the shear strength of kaolin increased in the CaCl₂ solution during ageing. In the presence of Ca²⁺ ions the max. shear stress value of bentonite was higher. The results of this study have shown that ageing has significant effects on the compressibility, permeability and shear strength of kaolinitic and bentonitic clayey soils.

• Korean Journal of Agricultural Science
• /
• v.27 no.1
• /
• pp.54-62
• /
• 2000

This study was performed to evaluate the food technological properties according to different emulsion state of carthamus red pigment. For making emulsion, lecithin was used as an emulsifier and polyglycerol monooleate(PGMO) and polyoxyethylene sorbitan monooleate(Tween 80) were used as an assistant, and glycerin, distilled water and soybean oil were used as base materials respectively. Paprika stock solution was used for comparing carthamin on the rheological properties. The results were described as following: 1. Hunter L-value was not drastically increased until passed by 8 hours for glycerin, carthamin, and lecithin mixed sample. 2. Hunter a-value was higher at carthamin added sample than others. and b-value was higher to paprika added sample than others. 3. The viscosity, shear rate and shear stress levels in which glycerin was used as base material were higher than soybean oil or distilled water. 4. In which soybean oil was used as base material. lecithin was not affected on the rheological properties. But, in which glycerin was used. the lecithin was higher affected on carthamin than paprika. 5. The value of shear stress was increased both carthamin and soybean oil. However, that of shear rate was shown similar trends.

• Transactions of Materials Processing
• /
• v.9 no.4
• /
• pp.421-427
• /
• 2000

The present study has focused on the development of shear textures during groove pressing in an aluminum alloy sheet. The shear components 23 and 13 developed during the groove pressing process. The process consisting of two steps of grooving and flattening each effectively gave rise to a high shear deformation In the sheet without reduction in thickness. The main texture component obtained from the process was the rotated Bs-orientation. The evolution of shear components during the groove pressing caused an increase in R-value of aluminum sheet comparing to a normally processed rolled sheet.

• Computers and Concrete
• /
• v.20 no.5
• /
• pp.539-544
• /
• 2017

Shear walls have high stiffness and strength; however, they lack energy dissipation and repairability. In this study, an innovative slotted shear wall featuring vertical slots and steel energy dissipation connectors was developed. The ductility and energy dissipation of the shear wall were improved, while sufficient bearing capacity and structural stiffness were retained. Furthermore, the slotted shear wall does not support vertical forces, and thus it does not have to be arranged continuously along the height of the structure, leading to a much free arrangement of the shear wall. A frame-slotted shear wall structure that combines the conventional frame structure and the innovative shear wall was developed. To investigate the ductility and hysteretic behavior of the slotted shear wall, finite element models of two walls with different steel connectors were built, and pushover and quasi-static analyses were conducted. Numerical analysis results indicated that the deformability and energy dissipation were guaranteed only if the steel connectors yielded before plastic hinges in the wall limbs were formed. Finally, a modified D-value method was proposed to estimate the bearing capacity and stiffness of the slotted shear wall. In this method, the wall limbs are analogous to columns and the connectors are analogous to beams. Results obtained from the modified D-value method were compared with those obtained from the finite element analysis. It was found that the internal force and stiffness estimated with the modified D-value method agreed well with those obtained from the finite element analysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1141-1151
• /
• 1998

An effective thermal conductivity measurement for suspensions of microparticles in oil mixture is conducted in order to evaluate the shear rate-dependence of the thermal conductivity of suspensions. Measurements are made for rotating Couette flows between two concentric cylinders. The rotating outer cylinder is immersed into a constant temperature water bath while the stationary inner cylinder is subject to a uniform heat fluff. Test fluids are made to be homogeneous suspensions, in which neutrally buoyant microparticles ($d=25{\sim}300{\mu}m$) are uniformly dispersed. The present measurements show strong shear-rate dependent thermal conductivities for the suspensions, which are higher than those at zero shear rate. The shear rate dependent thermal conductivity increases with the particle size and volume concentration.4 new model for shear rate-dependent thermal conductivity of microparticle suspensions is proposed; the correlation covers from zero shear rate value to asymptotic plateau value at moderately high shear rates.

• Geomechanics and Engineering
• /
• v.17 no.3
• /
• pp.253-259
• /
• 2019

Concrete-to-concrete bedding planes (CCBP) are observed from time to time due to the multistep hardening process of the concrete materials. In this paper, a series of direct/cyclic shear tests are performed on CCBP under static and dynamic normal load conditions to study the frictional behavior effect by the shear velocities, normal impact frequencies, horizontal shear frequencies, normal impact force amplitudes, horizontal shear displacement amplitudes and normal load levels. According to the experimental results, apparent friction coefficient k ($k=F_{Shear}/F_{Normal}$) shows different patterns under static and dynamic load conditions at the stable shear stage. k is nearly constant in direct shear tests under constant normal load conditions (DCNL), while it is cyclically changing with nearly constant peak value and valley value for the direct shear tests under dynamic normal load conditions (DDNL), where k increases with decreasing normal force and decreases with increasing normal force. Shear velocity has little influence on peak values of k for the DCNL tests, but increasing shear velocity leads to increasing valley values of k for DDNL tests. It is also found that, the valley values of k ascend with decreasing impact normal force amplitude in DDNL tests. The changing pattern of k for the cyclic shear tests under constant and dynamic normal load conditions (CCNL and CDNL tests) are similar, but the peak value of k is smaller in CDNL tests than that in CCNL tests. Normal load levels, shear displacement amplitudes, vertical impact frequencies, horizontal shear frequencies and normal impact force amplitudes have little influence on the changing pattern of k for the cyclic shear tests. The tests of this study provide useful data in understanding the frictional behavior of the CCBP under distinct loadings, and these findings are very important for analyzing the stability of the jointed geotechnical structures under complicated in situ stress conditions.

• The Journal of Engineering Geology
• /
• v.32 no.1
• /
• pp.173-191
• /
• 2022

In this study, the shear wave velocity of the ground was measured using Flat TDR, and the precision analysis of the measured value and the verification of field applicability were performed. The shear wave velocity measurement value was derived in the field using the piezo-stack combined in the Flat TDR. analyzed. As a result of the experiment, the average value of the change in shear wave speed at the time of grout material injection was 10.15 m/s at the beginning of age, and the average value of the change in shear wave speed after the 7th to 14th days was 65.99 m/s, showing a tendency to increase with age. Also, it was found that dry density and shear wave speed increased as the water content increased on the dry side, and that the dry density and shear wave rate decreased as the water content increased on the wet side as the water content increased. The shear modulus value derived from the field test was confirmed to be a minimum of 17.36 MPa and a maximum of 28.13 MPa, confirming a measurement value similar to the reference value. Through this, it can be seen that the measured value of the shear modulus using Flat TDR is reliable data, and it can be determined that the compaction management of the site can be effectively managed in the future.

• Proceedings of the KWS Conference
• /
• 2003.11a
• /
• pp.83-85
• /
• 2003

This paper is investigated the shear strength by using the micro shear-punch test method for Sn-37Pb alloy, binary and ternary alloys of environment-friendly Pb-free solder alloys which would be surely applicable to the electronic packages. As a result, in case of Max. shear strength, Sn-4Ag-0.5Cu has the highest value and Sn-37Pb has the lowest value on every condition of experiment temperature. Also, In case of Pb-free solder joint specimens, it was found that Pb-free solder alloys have higher value of shear strength than eutectic Sn-Pb solder alloy and Sn-4Ag-0.5Cu has the highest value.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.3
• /
• pp.11-18
• /
• 2019

The purpose of this study was to estimate the resistance capacity of a traditional wooden house with shear walls made of wood panel. In order to achieve the purpose of the study, the load - displacement test was carried out and the resistance moment values of the shear walls were proposed. The shear walls were made by placing studs with a nominal dimension of $38mm{\times}89mm$ at intervals of 600 mm, and attaching 12 mm thick plywood with 8-d size pegs at intervals of 150 mm. The type of traditional building wall was classified and showed the moment resistance ability of each wall type. This value is expressed as a proportional value divided by the moment resisting capacity of the standard size shear walls not divided into the divided small frames. Although some frames have proportional values larger than 1.0 even though they have openings, most of them show values smaller than 1.0. Also, even without the openings, it showed a smaller value than 1, such as 0.84 and 0.67.