• 대한기계학회논문집B
• /
• 제38권12호
• /
• pp.1027-1034
• /
• 2014

회전원판 위 표면에 작용하는 유동 전단응력은 표면마모를 발생시키는 주원인이다. 유체는 원심력에 의해 가장자리까지 자유표면을 갖는 박막유동으로 전달된다. 표면마모는 받음각 또는 곡률에 따른 전단응력 정도에 비례하여 차이를 보이게 된다. 전산해석을 통한 속도분포 기울기로 받음각에 기준한 곡률의 전단응력비를 비교하였다. 곡률반경 변화에 따른 전단유동의 응력감소를 모델링하여 표면마모를 효율적으로 줄일 수 있는 최적구간을 결정하는 것이 본 연구의 주제이며, 이 연구결과는 회전무화나 박막코팅과 같은 박막유동을 활용하는 기구의 최적설계에 적용될 수 있다.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4072-4083
• /
• 2022

Ultrasonic impact treatment (UIT) is carried out on the Ni-based alloy stainless steel pipe gas tungsten arc welding (GTAW) girth weld, the differences of microstructure, microhardness and shear strength distribution of the joint before and after ultrasonic shock are studied by microhardness test and shear punch test. The results show that after UIT, the plastic deformation layer is formed on the outside surface of the Ni-based alloy overlayer, single-phase austenite and γ type precipitates are formed in the overlayer, and a large number of columnar crystals are formed on the bottom side of the overlayer. The average microhardness of the overlayer increased from 221 H V to 254 H V by 14.9%, the shear strength increased from 696 MPa to 882 MPa with an increase of 26.7% and the transverse average residual stress decreased from 102.71 MPa (tensile stress) to -18.33 MPa (compressive stress), the longitudinal average residual stress decreased from 114.87 MPa (tensile stress) to -84.64 MPa (compressive stress). The fracture surface has been appeared obvious shear lip marks and a few dimples. The element migrates at the fusion boundary between the Ni-based alloy overlayer and the austenitic stainless steel joint, which is leaded to form a local martensite zone and appear hot cracks. The welded joint is cooled by FA solidification mode, which is forming a large number of late and skeleton ferrite phase with an average microhardness of 190 H V and no obvious change in shear strength. The base metal is all austenitic phase with an average microhardness of 206 H V and shear strength of 696 MPa.

• 대한토목학회논문집
• /
• 제28권3C호
• /
• pp.159-166
• /
• 2008

흙은 변형률에 따라 강성이 감소하는 비선형적 변형 특성을 가지지만, 매우 작은 변형률 영역($<10^{-3}%$)에서는 선형탄성적 특성을 갖는다고 알려져 있다. 본 연구에서는 응력 경로 시험 중 실시한 다축 벤더엘리먼트 시험을 통해 다양한 응력 상태에서 사질토의 이방적 전단탄성계수를 측정하고, 그 변화를 분석하고자 하였다. 응력 경로 시험에서는 내부 변형률 측정 장치 및 3 방향의 벤더 엘리먼트가 부착된 삼축 시험기를 이용하였다. 전단 중 응력비가 -0.5~1.5의 범위를 벗어나게 되면 축 방향 전단탄성계수는 응력과의 경험적 상관관계와 차이가 발생하였고, 이로부터 시료의 항복이 전단파 전달 구조를 변화시킴을 알 수 있었다. 수평방향 전단탄성계수의 변화는 전단 중 체적 상태의 변화와 밀접한 관계가 있음을 알 수 있었다.

• 산업기술연구
• /
• 제34권
• /
• pp.11-14
• /
• 2014

Viscosity and shear stress of the dental impression materials on commercial market(Imprint Garant LB(3M, U.S.A), EXAMIXFINE IT(GC, Japan), Vonflex S LB(Vericom, Korea), S-Silicone LB(Shinwon, Korea)) were measured with increasing shear rate from 50(1/sec) to 100(1/sec). The viscosity of EXAMIXFINE IT was decreased from 20,542(cP) to 14,684(cP), which is the shear thinning property of pseudoplastic as non-Newtonian fluid. Since the pseudoplastic property makes the impression material shear thinning and softly injected from cartridge, EXAMIXFINE IT might be popularly used in dentistry.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.259-264
• /
• 2002

In this study the shear strengths of a poorly grad ed rock material(d/sub max/≤50.8mm, C/sub u/=1.86) were determined by large direct shear test and large triaxial test. The obtained stress-strain curves by the above large shear tests for the rock materials are similar to the loose sand's or normally consolidated clay's curve, in which the peak strength does not appear obviously. And for the uniformly graded rock material the shear strength by large direct shear test may be overestimated around 1.54∼1.70 times that of large triaxial test.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2011년도 학술발표회
• /
• pp.46-46
• /
• 2011

Severe sediment erosion during floods occur disaster and economic losses, but general sediment erosion is basic mechanism to move sediment from upstream to downstream river. In addition, it is important process to change river form. Check dam, which is constructed in mountain stream, play a vital role such as control of sudden debris flow, but it has negative aspects to river ecosystem. Now a day, check dam of open type is an alternative plan to recover river biological diversity and ecosystem through sediment transport while maintaining the function of disaster control. The purpose of this paper is to verify sediment erosion progress of river bottom and bank as first step for river restoration after dam slit by cross-sectional shear stress and critical shear stress. Study area is upstream reach of slit check dam in mountain stream, named Wasada, in Japan. The check dam was slit with two passages in August, 2010. The transects were surveyed for four upstream cross-sections, 7.4 m, 34 m, 86 m, and 150 m distance from dam in October 2010. Sediment size was surveyed at river bottom and bank. Sediment of cobble size was found at the wetted bottom, and small size particles of sand to medium gravel composed river bank. Discharge was $2.5\;m^3/s$ and bottom slope was 0.027 m/m. Excess shear stress (${\tau}_{ex}$) was calculated for hydraulic erosion by subtracting the values of critical shear stress (${\tau}_{c}$) from the value of shear stress (${\tau}$) at river bottom and bank (${\tau}_{ex}=\tau-{\tau}_c$). Shear stress of river bottom (${\tau}_{bottom}$) was calculated using the cross-sectional shear stress, and bank shear stress (${\tau}_{bank}$) was calculated from the method of Flintham and Carling (1988). $${\tau}_{bank}={\tau}^*SF_{bank}((B+P_{bed})/(2^*P_{bank}))$$ where $SF_{bank}=1.77(P_{bed}/p_{bank}+1.5)^{-1.4}$, B is the water surface width, $P_{bed}$ and $P_{bank}$ are wetted parameter of the bed and bank. Estimated values for ${\tau}_{bottom}$ for a flow of $2.5\;m^3/s$ were lower as 25.0 (7.5 m cross-section), 25.7 (34 m), 21.3 (86 m) and 19.8 (150 m), in N/$m^2$, than critical shear stress (${\tau}_c=62.1\;N/m^2$) with cobble of 64 mm. The values were insufficient to erode cobble sediment. In contrast, even if the values of ${\tau}_{bank}$ were lower than the values for ${\tau}_{bottom}$ as 18.7 (7.5 m), 19.3 (34 m), 16.1 (86 m) and 14.7 (150 m), in N/$m^2$, excess shear stresses were calculated at the three cross-sections of 7.5 m, 34 m, and 86 m distances compare with ${\tau}_c$ is 15.5 N/$m^2$ of 16mm gravel. Bank shear stresses were sufficient for erosion of the medium gravel to sand. Therefore there is potential to erode lateral bank than downward erosion in a flow of $2.5\;m^3/s$. Undercutting of the wetted bank can causes bank scour or collapse, therefore this channel has potential to become wider at the same time. This research is about a potential of sediment erosion, and the result could not verify with real data. Therefore it need next step for verification. In addition an erosion mechanism for river restoration is not simple because discharge distribution is variable by snow-melting or rainy season, and a function for disaster control will recover by big precipitation event. Therefore it needs to consider the relationship between continuous discharge change and sediment erosion.

• Computers and Concrete
• /
• 제29권2호
• /
• pp.81-92
• /
• 2022

The influence of normal stress perpendicular to the potential shear plane was always neglected in existing researches, which may lead to a serious deviation of the shear strength of concrete members in practice designs and numerical analyses. In this study, a series of experimental studies are carried out in this paper, which serves to investigate the shear behavior of concrete under compression shear loading. Based on the test results, a three-phase shear failure model for cohesive elements are developed, which is able to take into consideration the influence of normal stress on the shear strength of concrete. To identify the accuracy and applicability of the proposed model, numerical models of a double-noted concrete plate are developed and compared with experimental results. Results show that the proposed constitutive model is able to take into consideration the influence of normal stress on the shear strength of concrete materials, and is effective and accurate for describing the complex fracture of concrete, especially the failure modes under compression shear loadings.

• 한국지반공학회논문집
• /
• 제22권11호
• /
• pp.47-54
• /
• 2006

비고결화된 흙의 전단파 속도는 모세관 현상을 무시할 수 있는 경우 유효응력의 함수로 표현할 수 있다. 그러나 지반에서의 응력상태는 등방성인 경우보다는 이방성인 경우가 대부분이므로 이러한 유효응력은 파가 전파되는 방향과 입자가 움직이는 방향의 두 가지로 나눠진다. 또한, 전단파 속도는 입자 특성에 따라 실험적으로 결정되는 ${\alpha}$계수와 ${\beta}$지수에 영향을 받는데 ${\beta}$지수의 경우 입상 매질(particulate material)의 접촉 특성(입자크기, 입자모양, 입자들의 구조)에 따라 결정되며, ${\alpha}$계수는 패킹(packing)의 형태(즉, 간극률과 coordination number), 입자를 만드는 재료의 특성, 입자간의 접촉 거동, 구조의 변화에 따라서 변화한다. 본 연구에서는 입자구조의 특성이 다른 점토, 모래, mica등의 재료로 압밀시험을 실시하고 벤더 엘리먼트를 통하여 유효응력 방향과 입자 이방성에 따른 전단파 속도를 측정하였다. 연구 결과, 둥근 입자로써 입자자체가 등방성인 경우에는 응력이방성에 의하여 전단파 속도의 크기가 달라지는 것으로 나타났다. 또한 전단파 속도는 동일한 응력 하에서 입자 배열에 의존하는 것으로 나타났다. 이번 연구는 지반구조물의 설계와 시공 시 전단파 속도와 전단탄성계수는 매우 신중하게 계산되고 사용되어져야 함을 제시하고 있다.

• International Journal of Vascular Biomedical Engineering
• /
• 제1권1호
• /
• pp.41-47
• /
• 2003

The patency rates of small diameter vascular grafts are disappointing because of the formation of thrombus and intimal hyperplasia. Among the various factors influencing the success of graft surgery, the compliance and the size of a graft are believed to be the most important physical properties of a vascular graft. Mismatch of compliance and size between an artery and a graft alters anastomotic flow characteristics, which may affect the formation of intimal hyperplasia. Among the hemodynamic factors influencing the development of intimal hyperplasia, the wall shear stress is suspected as the most important one. The wall shear stress distributions are experimentally measured near the end-to-end anastomosis models in order to clarify the effects of compliance and diameter mismatch on the hemodynamics near the anastomosis. The effects of radial wall motion, diameter mismatch and impedance phase angle on the wall shear rate distributions near the anastomosis are considered. Compliance mismatch generates both different radial wall motion and instantaneous diameter mismatch between the arterial portion and the graft portion during a flow cycle. Mismatch in diameter seems to be affecting the wall shear rate distribution more significantly compared to radial wall motion. The impedance phase angle also affects the wall shear rate distribution.

• 대한기계학회논문집B
• /
• 제28권12호
• /
• pp.1567-1572
• /
• 2004

Although accurate measurement of velocity profiles, multiple velocity vectors, and shear stress in arteries is important, there is still no easy method to obtain such information in vivo. This study shows the utility of combining ultrasound contrast imaging with particle image velocimetry (PIV) for non-invasive measurement of velocity vectors. The steady flow analytical solution and optical PIV measurements (for pulsatile flow) were used for comparison. When compared to the analytical solution, both echo PIV and optical PIV resolved the steady velocity profile well. Error in shear rate as measured by echo PIV (8%) was comparable to the error of optical PIV (6.5%). In pulsatile flow, echo PIV velocity profiles agreed well with optical PIV profiles. Echo PIV followed the general profile of pulsatile shear stress across the artery but underestimated wall shear at certain time points. These studies indicate that echo PIV is a promising technique for the non-invasive measurement of velocity profiles and shear stress.