• Transactions of Materials Processing
• /
• v.31 no.1
• /
• pp.23-28
• /
• 2022

Although the hole expansion test is currently the most commonly used method to evaluate the stretch flangeability of HSS, it has been criticized due to its poor repeatability and reproducibility for test results. This paper focuses on the development of a new measurement method to investigate the stretch flangeability of HSS. Two materials (DP590, DP980) were investigated with a hole expansion test and a developed test method. Test results showed that the developed test method could be used as one stretch flangeability test to help identify relevant parameters of the shearing process to avoid edge cracking.

• Structural Engineering and Mechanics
• /
• v.84 no.1
• /
• pp.129-141
• /
• 2022

It has previously been proposed that the yield-line method of analysis for reinforced concrete slabs could be automated via the use of rigid finite elements, assuming all deformations occur along element edges. However, the solutions obtained using this approach can be observed to be highly sensitive to mesh topology. To address this, a revised formulation that incorporates modified yield criteria to account for the presence of non-zero shear forces at interfaces between elements is proposed. The resulting formulation remains simple, with linear programming (LP) still used to obtain solutions for problems involving Johansen's square yield criteria. The results obtained are shown to agree well with literature solutions for various slab problems involving uniform loading and a range of geometries and boundary conditions.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.4
• /
• pp.239-252
• /
• 2023

In this study, bending and compression strength tests were performed to investigate effect of composition of layer layout of Larix cross-laminated timber (CLT) on mechanical properties. The Larix CLT consists of five laminae, and specimens were classified into four types according to grade and composition of layer. The layer's layout were composited as follows 1) cross-laminating layers in major and minor direction (Type A), and 2) cross-laminating external layer in major direction and internal layer applied grade of layer in minor direction (Type B). E12 and E16 were used as grades of lamina for major direction layer of Type A and external layer of Type B according to KS F 3020. In results of the bending test of CLT using same grade layer according to layer composition, the modulus of elasticity (MOE) of Type B was higher than Type A. In case of prediction of bending MOE of Larix CLT, the experimental MOE was higher than 1.00 to 1.09 times for Shear analogy method and 1.14 to 1.25 times for Gamma method. Therefore, it is recommended to predict the bending MOE for Larix CLT by shear analogy method. Compression strength of CLT in accordance with layer composition was measured to be 2% and 9% higher for Type A using E12 and E16 layers than Type B, respectively. In failure mode of Type A, progress direction of failure generated under compression load was confirmed to transfer from major layer to minor layer by rolling shear or bonding line failure due to the middle lamina in major direction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.109-116
• /
• 2004

Bent-axis piston pump have been commonly used in hydraulic systems because of high pressure level, best efficiency, low shear force on pistons and low operating costs. The other side, they have a few demerits like that they have the relatively high number of moving parts and more discharge pressure ripples. Especially, the discharge pressure ripples bring about vibrations and noises in hydraulic system components such as connecting pipes and control valves, so that these deteriorate the stability and accuracy of the systems. Therefore, the hydraulic systems having the bent-axis piston pump require the methods to reduce the discharge pressure ripples. So, the purpose of this paper is to reduce the discharge pressure ripples by the phase interference of pressure wave and to develope the analysis model of the pumps to predict the discharge pressure ripples. In this paper, the analysis model of the bent-axis piston pump was developed using the AMESim software, and the reliability of that was verified by the comparison with the experimental results. The hydraulic pipeline with a parallel line was used as the method to generate the phase interference of pressure wave. the dynamics characteristics of the hydraulic pipeline with a parallel line were analyzed by a transfer matrix method. the usefulness of the phase interference of pressure wave was investigated through the experiment and simulation. The results from the experiment and simulation said that the phase interference of pressure wave by the hydraulic pipeline with a parallel line could reduce the discharge pressure wave of the pump well. The analysis model of the bent-axis piston pump developed in this paper and the method of the phase interference by the hydraulic pipeline with a parallel line are expected to be helpful to achieve the design of the pump and to reduce the discharge pressure wave of the pump effectively.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.524-531
• /
• 2008

A method for representing detailed design information of steel bridge member is proposed on the basis of the IFC model. As a first step, bridge related entities in the IFC-BRIDGE V2 and their functions are analyzed. In addition, design documents of steel bridge members are analyzed to extract information items that are not handled in the IFC-BRIDGE V2. It is recommended that several entities in the IFC-BRIDGE V2, such as ifcBridgeFibre, IfcBridgeReferenceLine, and IfcBridgeSection, should be properly relocated. In addition, IfcBridgeStiffener, IfcBridgeJointSystem, IfcBridgeDiaphragm, and IfcBridgeShearConnector are added as subtypes of IfcBridgeElementComponent for representing the stiffener, joint system, diaphragm, and shear connector, respectively. The added new entities inherit all attributes of IfcProduct which is linked with other resources: geometric representation, placement, material information, and so on. Thus, it is considered that a proposed in-depth IFC-BRIDGE model can be used more widely.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.2
• /
• pp.152-158
• /
• 2007

Most of experimental visualizations and numerical results on the flow field separated form a leading edge around an unsteady foil show a continuous streakline from the leading edge and large reverse flow between the streakline and the suction surface. However, they have not exactly clarified yet the dynamic behavior of vortices separated from the leading edge because separation around an unsteady foil is very complicated phenomenon due to many parameters. In the present study the flow fields around pitching foils have been visualized by using a Schlieren method with a high speed camera in a wind tunnel at low Reynolds number regions. It has been observed that small vortices are shed discretely from the leading and trailing edge and that they stand in line on the integrated streakline of separation shear layer. By counting vortices in the VTR frames it was clarified that the number of vortex shedding from the leading and trailing edge during one pitching cycle strongly depends on the non-dimensional pitching rate. Futhermore the vortices moving up to the leading edge on the suction surface of the pitching foil are visualized. They play an important role to balance the number of vortex shedding from both edges.

• Journal of The Korean Astronomical Society
• /
• v.33 no.1
• /
• pp.47-55
• /
• 2000

Nonpotential characteristics of magnetic fields in AR 5747 are examined using Mees Solar Observatory magnetograms taken on Oct. 20, 1989 to Oct. 22, 1989. The active region showed such violent flaring activities during the observational span that strong X-ray flares took place including a 2B/X3 flare. The magnetogram data were obtained by the Haleakala Stokes Polarimeter which provides simultaneous Stokes profiles of the Fe I doublet 6301.5 and 6302.5. A nonlinear least square method was adopted to derive the magnetic field vectors from the observed Stokes profiles and a multi-step ambiguity solution method was employed to resolve the $180^{\circ}$ ambiguity. From the ambiguity-resolved vector magnetograms, we have derived a set of physical quantities characterizing the field configuration, which are magnetic flux, vertical current density, magnetic shear angle, angular shear, magnetic free energy density, a measure of magnetic field discontinuity MAD and linear force-free coefficient. Our results show that (1) magnetic nonpotentiality is concentrated near the inversion line in the flaring sites, (2) all the physical parameters decreased with time, which may imply that the active region was in a relaxation stage of its evolution, (3) 2-D MAD has similar patterns with other nonpotential parameters, demonstrating that it can be utilized as an useful parameter of flare producing active region, and (4) the linear force-free coefficient could be a evolutionary indicator with a merit as a global nonpotential parameter.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.4
• /
• pp.53-63
• /
• 1986

In this study, the stress distribution of rectangular bar under torsion, when warping of both ends is free or constrained, is investigated. Method of separation of variable and Fourier Series are used for the theoretical analysis, and 3dimensional photoelastic stress-freezing method for experimental analysis. The main results are as follows; 1) In the case of warping-constrained rectangular bar, the normal stresses are negligible because they are less then 0.5% of the shear stresses. The maximum normal stress is placed on the point of y=0.61 b when b/a=1 and it gradually moves to the corner y=b when the value of b/a is increased. 2) According to increase of the value of b/a, on the crossection, the maximum shear stress is placed on the middle point of the long side (x=${\pm}a$, y=0) when warping of both ends is free but the middle of the short side (x=0, y=${\pm} b$) when warping is constrained. The stress distribution is straight line when warping is constrained, namely, the stress distribution is proportional to the distance from the axis of centroid, but parabolic when warping is free. 3) The values of the combined stress of warping-constrained bar, if the influence of the loaded point is neglected, are generally smaller than those of warping-free.

• Journal of computational fluids engineering
• /
• v.15 no.2
• /
• pp.79-85
• /
• 2010

Aerodynamic design optimization of rotor airfoil has been performed with advanced design method for improved aerodynamic characteristics of ONERA airfoils. A multiple response surface method is used to consider various requirements in rotor airfoil design. Shape functions for mean camber line are proposed to extend possible design domain. Numerical simulations are performed using KFLOW, a Navier-Stokes solver with shear stress transport turbulence model. The present design method provides favorable configurations for the high performance rotor airfoil. Resulting optimized airfoils give better aerodynamic performance than the baseline airfoils.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.55-59
• /
• 2010

Aerodynamic design optimization of rotor airfoil has been performed with advanced design method for improved aerodynamic characteristics of ONERA airfoils as a baseline. A multiple response surface method is used to consider various consider various constraints in rotor airfoil design. Airfoil surface and mean camber line are modified using various shape functions. Numerical simulations are performed using KFLOW, a Navier-Stokes solver with shear stress transport turbulence model. The present design method provides favorable configurations for the high performance rotor airfoil. Resulting optimized air foils give better aerodynamic performance than the baseline airfoils.