• 한국구조물진단유지관리공학회 논문집
• /
• 제6권4호
• /
• pp.243-254
• /
• 2002

This study investigates the structural behavior of cracked or uncracked RC columns retrofitted with CFS and evaluates the shear retrofit performance through experiment. Experimental works were conducted for sixth specimens varied in the adhesion method of CFS, the ratio of shear reinforcement bar, and the existence of crack before retrofitting. Throughout cyclic test, the strength, stiffness, failure modes, and ductility are discussed. The test results show that the retrofitting method with CFS improve the shear strength and ductility. The crack width below 2mm, occurred before retrofitting, didn't reduce the shear strengthening effect.

• 한국정밀공학회지
• /
• 제31권10호
• /
• pp.873-879
• /
• 2014

UV curable adhesives with different acrylic functionalities were synthesized for temporary bonding and debonding process in 3D multi-chip packaging process. The aim is to study various factors which have an influence on UV curing. The properties and curing behaviors were investigated by gel fraction, peel strength, probe tack, and shear adhesion failure temperature. The results show that the properties and curing behaviors are dependent on not only acrylic functionalities of binders but also UV doses and coating thickness.

• 대한의용생체공학회:의공학회지
• /
• 제15권1호
• /
• pp.19-26
• /
• 1994

Sulfonated poly (ethyleneoxide)-grafted polyurethane (PU-PEO-$SO_3$) prepared by bulk modification was coated on a blood sac for electrohydraulic left ventricular assist device (ELVAD) implanted in dogs and its in vivo blood compatibility on shear stress was studied as compared with untreated Po. The effect of the wall shear stress on the protein adsorption unlike platelet adhesion is dependent on the surface characteristics of the material, although less proteins seem to be adsorbed in the region of the high shear stress. The thickness of total proteins adsorbed on PU-PEO-SOJ (400 ${\AA}$) by trans¬mission electron microscopy(TEM) was considerably lower than that of untreated PU(l,000~1,600 ${\AA}$), but PU-PEO-$SO_3$ showed high albumin adsorption, low fibrinogen and IgG adsorption, and low platelet adhesion as compared with untreated PU, suggesting that PU-PEO-$SO_3$ is more in vivo blood compatible. Therefore, it appears that such a blood compatible PU-PEO-$SO_3$ is useful for blood contacting biomaterials including artificial organs.

• 대한치과교정학회지
• /
• 제49권6호
• /
• pp.404-412
• /
• 2019

Objective: To assess shear bond strength and failure mode (Adhesive Remnant Index, ARI) of orthodontic brackets bonded to polymethylmethacrylate (PMMA) blocks for computer-aided design/manufacture (CAD/CAM) fabrication of temporary restorations, following substrate chemical or mechanical treatment. Methods: Two types of PMMA blocks were tested: $CAD-Temp^{(R)}$ (VITA) and $Telio^{(R)}$ CAD (Ivoclar-Vivadent). The substrate was roughened with 320-grit sandpaper, simulating a fine-grit diamond bur. Two universal adhesives, Scotchbond Universal Adhesive (SU) and Assure Plus (AP), and a conventional adhesive, Transbond XT Primer (XTP; control), were used in combination with Transbond XT Paste to bond the brackets. Six experimental groups were formed: (1) $CAD-Temp^{(R)}/SU$; (2) $CAD-Temp^{(R)}/AP$; (3) $CAD-Temp^{(R)}/XTP$; (4) $Telio^{(R)}$ CAD/SU; (5) $Telio^{(R)}$ CAD/AP; (6) $Telio^{(R)}$ CAD/XTP. Shear bond strength and ARI were assessed. On 1 extra block for each PMMA-based material surfaces were roughened with 180-grit sandpaper, simulating a normal/medium-grit ($100{\mu}m$) diamond bur, and brackets were bonded. Shear bond strengths and ARI scores were compared with those of groups 3, 6. Results: On $CAD-Temp^{(R)}$ significantly higher bracket bond strengths than on $Telio^{(R)}$ CAD were recorded. With XTP significantly lower levels of adhesion were reached than using SU or AP. Roughening with a coarser bur resulted in a significant increase in adhesion. Conclusions: Bracket bonding to CAD/CAM PMMA can be promoted by grinding the substrate with a normal/medium-grit bur or by coating the intact surface with universal adhesives. With appropriate pretreatments, bracket adhesion to CAD/CAM PMMA temporary restorations can be enhanced to clinically satisfactory levels.

• 접착 및 계면
• /
• 제22권1호
• /
• pp.8-15
• /
• 2021

본 연구에서는 우레탄 변성 에폭시의 유연성 부여를 위해 propylene glycol(PPG) 기반 diamine인 Jeffamine D-400을 이용하여 폴리올을 만들고 이를 이용하여 우레탄 변성 에폭시를 합성하였다. Bisphenol A diglycidyl ether(BADGE)에 합성한 우레탄 변성 에폭시와 경화제, 경화촉진제를 배합하여 에폭시 접착제를 제조하고 접착강도 측정으로 전단 강도를 측정하였다. 측정 결과 합성한 우레탄 변성 에폭시의 우레탄 결합과 PPG사슬 도입을 통한 유연성 부여 효과로 인해 전단 강도와 전단 신율이 증가하는 경향을 보였다. 이러한 결과는 높은 가교 밀도로 인해 사용에 제약을 받고 있는 구조용 접착제에 적용이 가능할 것으로 판단된다.

• 접착 및 계면
• /
• 제21권1호
• /
• pp.27-33
• /
• 2020

유리섬유강화 복합재료 (GFRC)의 표면거칠기에 따른 에폭시 접착제의 접착강도를 평가하였고 최적의 표면거칠기를 선정하였다. 서로 다른 입자크기의 알루미나 (Al2O3) 입자를 GFRC의 표면에 분사하였고 이를 통하여 서로 다른 표면거칠기를 부여하였다. 표면거칠기를 정량화 하였고 표면거칠기에 따른 표면관찰을 진행하였다. 각 표면거칠기에 따른 접촉각을 측정하였고 이를 통하여 표면에너지를 계산하였으며, 에폭시 접착제와의 접착일을 계산 및 비교하여 접착력을 예측하였다. 단일랩전단 시험을 통해 접착강도를 평가하였고 거칠기에 따라 접착강도가 증가된다는 것을 확인하였다. 박리 후 표면을 관찰해 보았을 때 기지재인 GFRC의 박리 정도가 다른 것을 확인하였고 최종적으로 표면거칠기의 최적조건을 확인할 수 있었다.

• Geomechanics and Engineering
• /
• 제20권4호
• /
• pp.299-312
• /
• 2020

The aim of this paper was to investigating the effects of soil relative density, construction materials roughness, oil type (gasoil, crude oil, and used motor oil), and oil content on the internal and interface shear behavior of sand with different construction materials by means of a modified large direct shear test apparatus. Tests conducted on the soil-soil (S-S), soil-rough concrete (S-RC), soil-smooth concrete (S-SC), and soil-steel (S-ST) interfaces and results showed that the shear strength of S-S interface is always higher than the soil-material interfaces. Internal and interface friction angles of sand beds increased by increase in relative density and decreased by increasing oil content. The oil properties (especially viscosity) played a major role in interface friction behavior. Despite the friction angles of contaminated sands with viscous fluids drastically decreased, it compensated by the apparent cohesion and adhesion developed between the soil grains and construction materials.

• 접착 및 계면
• /
• 제5권1호
• /
• pp.21-28
• /
• 2004

본 연구에서는 사슬말단에 chloropropyl 유기관능그룹을 가지고 있는 실란결합체인 3-chloropropyltrimethoxysilane(CTMS)을 사용하여 여러 농도에서 유리섬유 표면에 사이징 처리하여 유리섬유/나일론 6 및 유리직물/나이론 6 복합재료를 제조하였다. 단섬유 microbonding 시험에 의한 유리섬유/나일론 6 복합재료의 계면전단강도와 short-beam 전단시험과 동역학적 열특성 분석 방법을 통하여 유리직물/나일론 6 복합재료의 층간전단강도 및 저장탄성률에 미치는 결합체 농도의 영향을 각각 조사하였다. CTMS 결합제의 농도가 증가할수록 복합재료의 계면특성이 향상되었다. 결합제의 농도 변화에 대한 유리섬유강화 나일론 6 복합재료의 계면전단강도, 층간전단강도, 층간파단양상 그리고 저장탄성률 등 각 특성 변화의 경향이 서로 일치하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.449-449
• /
• 2011

We reported the direct effect of intrinsic surface energy of dry adhesive material to the Van der Waals and capillary forces contributions of the total adhesion force in an artificial gecko-inspired adhesion system. To mimic the gecko foot we fabricated tilted nanohairy structures using both lithography and ion beam treatment. The nanohairy structures were replicated from Si wafer mold using UV curable polymeric materials. The control of nanohairs slanting angles was based on the uniform linear argon ion irradiation to the nanohairy polymeric surface. The surface energy was studied utilizing subsequent conventional oxygen ion treatment on the nanohairy structures which resulted in gradient surface energy. Our shear adhesion test results were found in good agreement with the accepted Van der Waals and capillary forces theory in the gecko adhesion system. Surface energy would give a direct impact to the effective Hamaker constant in Van der Waals force and the filling angle (${\varphi}$) of water meniscus in capillary force contributions of gecko inspired adhesion system. With the increasing surface energy, the effective Hamaker constant also increased but the filling angle decreased, resulting in a competition between the two forces. Using a simple mathematical model, we compared our experimental results to show the quantitative contributions of Van der Waals and capillary forces in a single adhesion system on both hydrophobic and hydrophilic surfaces. We found that the Van der Waals force contributes about 82.75% and 89.97% to the total adhesion force on hydrophilic and hydrophobic test surfaces, respectively, while the remaining contribution was occupied by capillary force. We also showed that it is possible to design ultrahigh dry adhesive with adhesion strength of more than 10 times higher than apparent gecko adhesion force by controlling the surface energy and the slanting angle induced-contact line of dry adhesive the materials.

• 접착 및 계면
• /
• 제23권4호
• /
• pp.122-129
• /
• 2022

본 연구에서는 산소 플라즈마 처리시간을 실험 변수로 하여 금속섬유를 처리한 후 섬유표면에 산소함유 기능성 관능기를 도입하여 금속섬유의 친수성을 향상시키기 위한 연구로 플라즈마 처리 전, 후의 표면 특성 변화를 scanning electron microscope (SEM)과 x-ray photoelectron spectroscopy (XPS)를 사용하여 관찰하였다. 또한 플라즈마 처리시간이 금속섬유의 표면에 미치는 영향을 관찰하기 위해 극성 용매와 비극성 용매에 대한 금속섬유의 접촉각 변화를 측정하였다. 측정된 접촉각을 이용해 표면 자유에너지 변화를 계산한 후 산소 플라즈마 처리 전, 후의 금속섬유에 대한 접촉각과 표면 자유에너지를 비교하였으며 접착일과의 상관관계도 고찰하였다. 이런 금속섬유의 표면 변화가 다른 소재와의 복합 시 계면에서의 전단강도 향상에 미치는 영향을 알아보기 위해 microdroplet 시편을 제조하여 계면 전단강도를 측정하였으며 접착일과의 상관관계도 함께 파악하였다. 따라서, 금속섬유의 산소플라즈마 처리는 섬유표면에 물리적인 표면적 증가로 인한 수지와의 접촉면의 증가와 표면의 산소함유 기능성 관능기의 도입에 따른 접촉각, 표면 에너지의 변화에 따른 표면 친수화로 고분자 수지와의 계면 전단강도를 향상시켜주는 결과를 얻었다.