• Journal of Power System Engineering
• /
• v.1 no.1
• /
• pp.98-105
• /
• 1997

In general, crankshafts which are used in internal combustion reciprocating engines are subjects to high torsional vibration. Therefore, a damper is often used to minimize the torsional vibration in reciprocating engines. In this paper, in order to investigate damping performance of viscous damper, the real effective viscosity and complex damping coefficient of silicone oil, and the effective inertia moment of inertia ring are calculated considering the relative motion between damper casing and inertia ring. Based on these results multi-cylinder shaft is modeled into equivalent 2-degree of freedom system and optimum condition is estimated by calculating the amplification factor of viscous damper. Also the test damper was manufactured according to the result of theoretical investigation, the performance and durability was ascertained through experimental examination.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.4
• /
• pp.314-323
• /
• 2014

In this study, a gearbox and blade were modeled in the MASTA program, and the housing and carrier components were modeled using a finite element method. Using substructure synthesis, all the components were combined and used to establish a vibration model of a 2.5-MW wind turbine gearbox. In addition, the safety displacement factor was evaluated using an AGMA data sheet about bearing's outer race for the input shaft and output shaft. As a result, the bearing's outer race for the input shaft, and the radial and axial responses were satisfied by the $1^{st}$ and $2^{nd}$ planetary gears and the $3^{nd}$ helical gear transmission error(TE), respectively. However, the output shaft support bearing's outer race responses were not satisfied with the radial response by the $2^{nd}$ TE and axial response by the $3^{rd}$ TE. To reduce the vibration, tooth modification was needed. After profile tooth modification, at the outer race of the output shaft support bearing, the radial response was reduced by approximately $20{\mu}m$, and the axial response was reduced by approximately $6{\mu}m$.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.4
• /
• pp.31-39
• /
• 2001

Composite propeller shafts for a vehicle have major advantages such as reduction of vibration, noise, and weight. A propeller shaft was designed with a carbon/epoxy composite material using the finite element method(FEM), and prototype shafts for tests were manufactured by the filament winding manufacturing process. In order to verify the design procedure by FEM, Two kinds of experimental tests were carried out using a FFT analyzer with impact hammers and a critical speed measuring apparatus for measurement of natural frequencies and critical speeds. The difference between the FEM analysis result and the test result was less than 3.4%, showing FEM analysis results to be acceptable. The parametric study was focused on determining the factor affecting the vibration and strength characteristics of the propeller shaft based on FEM. In investigation of the change in natural frequency without an increase in propeller shaft weight, it was found that the winding angle is the most significant factor affecting the vibration and strength characteristics.

• Journal of Mechanical Science and Technology
• /
• v.14 no.7
• /
• pp.722-729
• /
• 2000

The goal of this paper is to describe an advanced method of a crack detection: a new way to localize position and to estimate depth of a crack on rotating shaft. As a first step, the shaft is physically modelled with a finite element method and the dynamic mathematical model is derived using the Hamilton principle; thus, the system is represented by various subsystems. The equations of motion of the shaft with a crack are established by adapting the local stiffness change through breathing and gaping from the crack to an undamaged shaft. This is the reference system for the given system. Based on a model for transient behavior induced from vibration measured at the bearings, a nonlinear state observer is designed to detect cracks on the shaft. This is the elementary NL-observer (Beo). Using the observer, an Estimator (Observer Bank) is established and arranged at the certain position on the shaft. When a crack position is localized, the procedure for estimating of the depth is engaged.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.2
• /
• pp.56-62
• /
• 2017

In this research, reverse engineering was applied to the product manufactured by "Vanzetti" from Italy to develop a localized cryogenic submerged pump used in small-scale LNG liquefaction plants. The results of modal analysis of the impeller and shaft confirmed that the resonance frequency of the impeller and shaft played an important role in the rotor. Modal analysis of the rotor confirmed that the forcing frequency had no influence on the resonance phenomenon.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.922-928
• /
• 1998

This paper presents the automatic alignment measuring system for improving the accuracy and working time of alignment of large vertical hydraulic pump turbine. It is general practice that rotating shaft should run within acceptable vibration limit. In order to obtain better run-out data of multi-stage rotor, careful and accurate alignment approach must be established. Generally, present alignment procedure are required several iterative works and so many manpower. Therefore, the new system has been developed using a vector calculation algorithm, laser sensor and data acquisition devices. As a result of appling to actual machines, it is confirmed that manpower is saved up to an average 90%.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.131-131
• /
• 2017

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1026-1031
• /
• 2001

In this paper. the dynamic characteristics of a super high-speed tilting-pad air bearing(TPGB) used in a turbo expander with high expansion ratio are analyzed. The dynamic behavior and stability of a rotary system supported by two journal air bearings are investigated numerically. The transient response of the shaft is obtained by simultaneously solving the equation of motion of the shaft and the dynamic Reynolds equation. The stiffness and damping coefficients of the bearing are calculated from the loading coefficients of the bearing are calculated from the loading capacity. shaft velocity and displacement by using a curve fitting method. The natural frequencies of the 1st and 2nd rigid modes can be calculated from these coefficients. The theoretical method of a rigid rotor system is verified by experimentsut.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.571-572
• /
• 2009

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2013.10a
• /
• pp.163-164
• /
• 2013

Two-Way CAR-FERRY land and islands, islands to islands, the connection between sustainable marine transportation in conjunction with the increasing demand of tourists, according to the associated coastal maritime tourism and passenger transport has a role. Subsequent Two-Way CAR-FERRY and the increased ease of use due to berthing maritime accidents can be reduced. Two-Way CAR-FERRY as the draft (even) in the state on both sides of the propeller, because the propeller due to the small diameter, low speed forward flight by the reaction at the shaft and propeller damage can occur. Engine output accordingly, linear and torsional vibration reducer by, elastic coupling selection transverse vibration and shaft alignment (Shaft alignment) considering the shaft design (bearing size, width, thickness) and the primary drive shaft support portion of the hull structure of evaluated for quality.