• 조명전기설비학회논문지
• /
• 제25권6호
• /
• pp.57-67
• /
• 2011

Purpose of this study is to find the mitigation method of magnetic field by finite length multi-conductors such as indoor distribution lines and to be applicable to design of the distribution lines. For this purpose, exact formula about the components $B_x$, $B_y$, $B_z$ of magnetic field need in case of straight line-conductor with finite length forward any direction. In this study simple formula of the components were deduced and by using these formula magnetic fields for various models of line-configurations were calculated. And also a calculation method of induced currents in conductive shield was presented and using this method, programing of calculation is relatively easy and calculation time is short. The magnetic field after cancellation by these induced currents was calculated. All of calculations were performed by Matlab 7.0 programs. Through the calculation results it could be obtained followings for the mitigation of magnetic fields. The separation between conductors ought to be smaller than smaller as possible. In case of 3-phase, delta configuration is more effective than flat configuration. In case of 3-phase, unbalanced currents ought to be reduced as possible.. In case of more than two circuits of 3-phase, adequate locations of each phase-conductor such as rotating configuration of 3-phase conductors are more effective. The magnetic shielding effect of the conductive shielding sheet is very high.

• Membrane and Water Treatment
• /
• 제3권1호
• /
• pp.1-23
• /
• 2012

The coupling of anaerobic biological process and membrane separation could provide excellent suspended solids removal and better biomass retention for wastewater treatment. This coupling improves the biological treatment process while allowing for the recovery of energy through biogas. This review gives a basic description of the anaerobic wastewater treatment process, summarizes the state of the art of anaerobic membrane bioreactors (AnMBRs), and describes the current research trends and needs for the development of AnMBRs. The research interest on AnMBR has grown over the conventional anaerobic processes such as upflow anaerobic sludge blanket (UASB). Studies on AnMBRs have developed different reactor configurations to enhance performances. The AnMBR performances have achieved comparable status to other high rate anaerobic reactors. AnMBR is highly suitable for application with thermophilic anaerobic process to enhance performances. Studies indicate that the applications of AnMBR are not only limited to the high strength industrial wastewater treatment, but also for the municipal wastewater treatment. In recent years, there is a significant progress in the membrane fouling studies, which is a major concern in AnMBR application.

• 한국건축시공학회지
• /
• 제23권5호
• /
• pp.519-526
• /
• 2023

본 연구는 겉보기 비저항 측정에 포함되는 주변 철근의 영향을 파악하기 위해 단근과 복근을 매립한 콘크리트 실험체를 제작하였다. 실험체는 중심에서부터 0.03m, 0.04m, 0.05m의 위치에 단근 또는 복근을 배근하고, 겉보기 비저항 측정은 실험체별 정해진 위치까지 0.01m의 간격으로 실시하였다. 모든 실험체는 철근의 상부위치에서 겉보기 비저항이 최저치를 보였고 복근 실험체는 단근에 비해 배근 중심위치에서 낮은 측정치를 나타내며 주변 철근의 영향이 측정 결과에 반영되었음을 보였다. 또한 배근 간격이 넓을수록 철근의 위치가 명확하게 구분되는 것을 알 수 있었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.79-84
• /
• 2004

For the non-premixed interacting jet flames, it has been reported that if eight small nozzles are arranged along the circle of 40 $^{\sim}$ 72 times the diameter of single jet, the flames are not extinguished over 2oom/s. In this research, experiments were extended to the partially premixed cases to reduce both flame temperature and NOx emission. Nine nozzles were used- eight was evenly located along the perimeter of the imaginary circle and one at the geometric centre. The space between nozzles, S, the equivalence ratio, ${\Phi}$, the exit velocity and the role of the jet from the centre nozzle were considered. Normally, flame was lifted and flame base was located inside the imaginary circle made by the nozzle. As nozzles went away from each other, blowout velocity increased and then decreased. The maximum blowout velocity diminished with the addition of air to the fuel stream. When the fuel and/or oxidizer were not fed through the centre nozzle, the maximum blowout velocity obtained by varying Sand ${\Phi}$ was around 160m/s. Optimum nozzle separation distance at which peak blowout velocity obtained also decreased with ${\Phi}$ decrease. Flame base became leaner as approaching to the blowout. It seemed that lots of air was supplied to the flame stabilizing region by the entrainment and partially premixing. To approve this idea and to enhance the blowout velocity, fuel was supplied to the centre region. With the small amount of fuel through the centre nozzle, partially premixed flame could be sustained till sonic velocities. It seemed that the stabilizing mechanism in partially premixed interacting flame was different from that of non-premixed case because one was stabilized by the fuel supply through the centre nozzle but the other destabilized.

• 한국경제지리학회지
• /
• 제14권4호
• /
• pp.671-683
• /
• 2011

교통 및 통신의 기술적 발달은 기업에게 입지적 자유를 증가시켰고 이는 기업 조직의 공간 변화를 통해 더 큰 이윤을 창출할 수 있게끔 하였다. 기업의 공간조직은 기능별로 최적의 장소로 가려고 하며, 이로 인하여 기업 기능에 적합한 공간에서는 오히려 집적이 심화되는 현상을 보인다. 본 연구는"분산적 집중"현상에 대하여 그 실재를 검증하고자 바이오산업 중 제약기업을 사례로 하여 이들의 기능별 분절과 분산 입지의 경향, 그리고 분산된 기업 기능의 공간적 집적에 대하여 분석하였다. 연구 결과 기업 공간 조직의 분산 과정은 생산 규모가 확대되고 연구 기능이 고도화 될수록 분리되어 최종적으로 3개의 부문이 각각 분산 입지하는 것으로 나타났다. 기능의 공간적 집중 분석 결과, 본사는 서울에 집중되어 있으며 생산기능의 대부분은 경기도에, 연구개발 기능은 소수의 집적지로 집중하는 패턴을 보이고 있어 제약기업을 대상으로 했을 때 기업 기능의 분산적 집중 입지는 실제로 나타나고 있는 것으로 밝혀졌다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1215-1220
• /
• 2004

Reactive distillation (RD) is a combination process where both separation and reaction are considered simultaneously in a single vessel. This kind of combination to enhance the overall performance is not a new attempt in the chemical engineering areas. The recovery of ammonia in the classic Solvay process for soda ash of the 1860s may be cited as probably the first commercial application of RD. The RD system has been used for a long time as a useful process and recently the importance of the RD is enlarged more and more. In addition to that, the application fields of RD are diversely diverged. To make the most of the characteristic of RD system, we must decide the best operating condition under which the process shows the most effective productivity and should decide the best control algorithm which satisfies an optimal operating condition. Phosgene which is a highly reactive chemical is used for the production of isocyanates and polycarbonates. Because it has high reactivity and toxicity, its utilization is increasingly burdened by growing safety measures to be adopted during its production. Dimethyl Carbonate (DMC) was proposed as a substitute of phosgene because it is non-toxic and environmentally benign chemical. In this study, RD is used for DMC production process and the transesterification is performed inside of column to produce DMC. In transesterification, the methanol and ethylene carbonate (EC) are used as the reactants. This process use homogeneous catalyst and the azeotrope exists between the reactant and product. Owing to azeotrope, we should use two distillation columns. For this DMC production process, we can suggest two configurations. One is EC excess process and the other is methanol excess process. From the comparison of steady state simulation results where the Naphtali-Sandholm algorithm is used, it showed the better performance to use the methanol excess process configuration than EC excess process. Then, the dynamic simulation was performed to be based on the steady state simulation results and the optimal control system was designed. In addition to that, the optimal operating condition was suggested from previous results.

• 한국발생생물학회지:발생과생식
• /
• 제16권1호
• /
• pp.59-67
• /
• 2012

Previously, we found that $Zap70$ (Zeta-chain-associated protein kinase) expressed in the mouse oocytes and played significant role in completion of meiosis specifically at MI-MII (metaphase I-II) transition. Microinjection of $Zap70$ dsRNA into the cytoplasm of germinal vesicle oocyte resulted in MI arrest, and exhibited abnormalities in their spindles and chromosome configurations. The purpose of this study was to determine the mechanisms of action of $Zap70$ in oocyte maturation by evaluating downstream signal networking after $Zap70$ RNAi (RNA interference). The probe hybridization and data analysis were used by Affymetrix Gene Chip Mouse Genome 430 2.0 array and GenPlex 3.0 (ISTECH, Korea) software, respectively. Total 1,152 genes were up (n=366) and down (n=786) regulated after $Zap70$ RNAi. Among those genes changed, we confirmed the expressional changes of the genes involved in the regulation of actin cytoskeleton and MAPK (mitogen-activated protein kinase) signaling pathway, since the phenotypes of $Zap70$ RNAi in oocytes were found in the changes in the chromosome separation and spindle structures. We confirmed the changes in gene expression in the actin skeletal system as well as in the MAPK signaling pathway, and concluded that these changes are main cause of the aberrant chromosome arrangement and abnormal spindles after $Zap70$ RNAi.

• 대한기계학회논문집B
• /
• 제29권1호
• /
• pp.71-79
• /
• 2005

For the non-premixed interacting jet flames, it has been reported that if eight small nozzles are arranged along the circle of $40{\sim}72$ times the diameter of single jet, the flames are not extinguished even in 200m/s. In this research, experiments were extended to the partially premixed cases to reduce both flame temperature and NOx emission. Nine nozzles were used- eight was evenly located along the perimeter of the imaginary circle and one at the geometric centre. The space between nozzles, S, the equivalence ratio, ${\phi}$, the exit velocity and the role of the jet from the centre nozzle were considered. Normally, flame was lifted and flame base was located inside the imaginary circle made by the nozzle. As nozzles went away from each other, blowout velocity increased and then decreased. The maximum blowout velocity diminished with the addition of air to the fuel stream. When the fuel and/or oxidizer were not fed through the centre nozzle, the maximum blowout velocity obtained by varying S and ${\phi}$ was around 160m/s. Optimum nozzle separation distance at which peak blowout velocity obtained also decreased with ${\phi}$ decrease. Flame base became leaner as approaching to the blowout. It seemed that lots of air was supplied to the flame stabilizing region by the entrainment and partially premixing. To approve this idea and to enhance the blowout velocity, fuel was supplied to the centre region. With the small amount of fuel through the centre nozzle, partially premixed flame could be sustained till sonic velocities. It seemed that the stabilizing mechanism in partially premixed interacting flame was different from that of non-premixed case because one was stabilized by the fuel supply through the centre nozzle but the other destabilized.

• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3764-3773
• /
• 2012

본 연구에서는 methyl ethyl ketone (MEK)와 물의 이성분계 공비 혼합물의 공비조성이 압력에 따라서 민감하게 변하는 현상을 이용하여 압력변환 증류(pressure-swing distillation; PSD)공정을 통해서 순도가 99.9mole% 이상의 MEK를 분리해 내기 위한 전산모사 및 공정 최적화를 수행하였다. 전산모사를 위하여 상용성 화학공정 모사기인 Invensys사의 PRO/II with PROVISION 9.1을 활용하였고, 열역학 모델식으로는 Wilson 액체 활동도계수 모델식을 활용하였다. PSD 공정은 저압 및 고압의 증류탑 2기의 증류탑 배열을 사용하는데 저압 증류탑을 전단에 두는 저압-고압 증류탑 배열과 저압 증류탑을 후단에 두는 고압-저압 증류탑 배열로 분류할 수 있다. 본 연구에서는 각각의 배열에 대한 증류탑 환류비와 원료 주입단의 위치를 조절변수로 하여 총 재비기의 heat duty의 합을 최소화시킨 후 두 공정배열을 서로 비교하였다.

• Earthquakes and Structures
• /
• 제16권6호
• /
• pp.715-726
• /
• 2019

Several municipal seismic vulnerability investigations have been identified pounding of adjacent structures as one of the main hazards due to the constrained separation distance between adjacent buildings. Consequently, an assessment of the seismic pounding risk of buildings is superficial in future adjustment of design code provisions for buildings. The seismic lateral oscillation of adjacent buildings with eccentric alignment is partly restrained, and therefore a torsional response demand is induced in the building under earthquake excitation due to eccentric pounding. In this paper, the influence of the eccentric seismic pounding on the design demands for adjacent symmetric buildings with eccentric alignment is presented. A mathematical simulation is formulated to evaluate the eccentric pounding effects on the seismic design demands of adjacent buildings, where the seismic response analysis of adjacent buildings in series during collisions is investigated for various design parameters that include number of stories; in-plan alignment configurations, and then compared with that for no-pounding case. According to the herein outcomes, the effects of seismic pounding severity is mainly depending on characteristics of vibrations of the adjacent buildings and on the characteristics of input ground motions as well. The position of the building wherever exterior or interior alignment also, influences the seismic pounding severity as the effect of exposed direction from one or two sides. The response of acceleration and the shear force demands appear to be greater in case of adjacent buildings as seismic pounding at different levels of stories, than that in case of no-pounding buildings. The results confirm that torsional oscillations due to eccentric pounding play a significant role in the overall pounding-involved response of symmetric buildings under earthquake excitation due to horizontal eccentric alignment.