• Journal of Energy Engineering
• /
• v.20 no.4
• /
• pp.353-357
• /
• 2011

An embedded two-axis solar tracking system was developed by using AVR micro controller for enhancing solar energy utilization. The system consists of an Atmega128 micro controller, two step motors, two step drive modules, CdS sensors, GPS module and other accessories needed for functional stability. This system is controlled by both an astronomical method and an optical method. Initial operation is performed by the result from the astronomical method, which is followed by the fine controlled operation using the signals from Cds sensors. The GPS sensor generates UTC, longitude and latitude data where the solar tracker is installed. A database of solar altitude, azimuth, and sunrise and sunset times is provided by UART (Universal Asynchronous Receiver/Transmitter).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.451-456
• /
• 2016

Because GPS signals are weak, system jamming is a real and present danger. This can happen when the receiver is subjected to intentional or unintentional interference by a transmitter. If the jamming signal is strong enough, the receiver can be operated to take corrective action automatically. Current methods to protect GPS receiver from jamming condition are based on spatial filtering. In this paper, the beamforming as referred to in signal processing technique used in arrays for directional signal reception was suggested and analyzed for anti-jamming. In order to change the directionality of the array when receiving a jamming signal, a beamformer can control the signal at each sensor. Therefore, cutoff angle ${\theta}$ was measured in the opposite direction of the jammer. GPS signals are only processed when the antenna element is within inside the cutoff angle. As a result, GPS positioning can be used in condition under cutoff angle $30^{\circ}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.7
• /
• pp.1531-1538
• /
• 2015

In this paper, we proposed receiver structure based on an iterative turbo equalization to cope with phase difference between two sensors in MIMO underwater communication channel. In a space-time coded system, it is often assumed that there are no phase errors among the multiple transmitter and receiver chains. In this paper, we have studied the effect of the phase errors between different transmit sensors and different propagation paths in the environment of MIMO underwater communication system, and have shown through BER performance by computer simulations that the bit-error-rate performance can be severely degraded. A decision-directed estimation and compensation algorithm has been proposed to minimize their effects on the system performance. In this paper, we investigate the phase differences and their effects on multiple-input and multiple-output systems, and propose a compensation algorithm for underwater channel model to minimize their effects.

• Journal of Advanced Navigation Technology
• /
• v.23 no.5
• /
• pp.452-459
• /
• 2019

In this paper, we describe a PCM encoder structure that can update the telemetry system parameters in real time. In the PCM encoder, an analog signal control unit for FPGA, flash memory, and sensor data acquisition was constructed. UART communication, analog signal control, flash memory control, and frame generation are possible through logic inside FPGA of PCM encoder. UART communication allows the PC to transmit parameter data to the PCM encoder, and flash memory is controlled to update the parameter of the telemetry system in real time and finally the frame is formed. Simulation and verification were performed to confirm whether the parameter data is updated in real time, and the proposed structure was used to construct a telemetry system with enhanced flexibility and convenience.

• Journal of the Korean Society for Railway
• /
• v.19 no.4
• /
• pp.468-479
• /
• 2016

In order to supply power to online monitoring systems that are attached to high voltage catenary or overhead wires, a wireless power transfer system is required that is able to transmit power over the insulation gap. Such wireless power transfer systems have transmitter and receiver coils that have diameters of over 10cm. This paper focused on an investigation of the sources of loss in the coils when the coils are fabricated using printed circuit board technology. Using finite element simulation results, it has been shown that the dielectric loss in the substrate was the dominant source of the total loss. It has been demonstrated that the selection of a proper dielectric material was the most critical factor in reducing the loss. For further reduction of the loss, the distributed tuning capacitor method and the slotting of the inter-turn spaces have been proposed. For the evaluation of the proposed methods, four coils have been fabricated and their equivalent series resistances and quality factors were measured. Measured quality factors were greater than 300, which means that these devices will be helpful in achieving high coil-to-coil efficiency.

• The Journal of the Acoustical Society of Korea
• /
• v.41 no.2
• /
• pp.150-158
• /
• 2022

This paper presents the results of a sea trial for very long range spread spectrum underwater acoustic communication conducted in the East Sea in September 2021. Signals were collected through 8 vertical sensors, and the range between the transmitter and receiver was about 160 km. 30 bps Multi-Code Spread Spectrum (MCSS) method and 100 bps Chirp Spread Spectrum method were used for the transmitting signal generation. The results show that when the channel coding technique was not used in a single channel, the uncoded bit error rate was high, but when the Equal Gain Combining (EGC) diversity technique was used after frame synchronization in each receiving channel, the uncoded bit error rate was reduced to 0.1 or less.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.6
• /
• pp.175-181
• /
• 2019

For the purpose of Application to the small radar sensor, the MMIC Chip, which is the core component of the W-band, was designed in Korea according to the characteristics of the transceiver and manufactured by 0.1㎛ GaAs pHEMT process, and compared with the MMIC chip purchased overseas. The noise figure of low noise amplifier, insertion loss of the switch and image rejection performance of the down-converted mixer MMIC chip showed better characteristics than those of commercial chips. The MMIC chip developed in domestic was applied to the transmitter and receiver through W-band waveguide low loss transition structure design and impedance matching to verify the performance after the fabrication is 9.17 dB, which is close to the analysis result. As a result, it is judged that the transceiver can be applied to the small radar sensor better than the MMIC chip purchased overseas.