• The Journal of the Acoustical Society of Korea
• /
• v.38 no.5
• /
• pp.534-542
• /
• 2019

In active SONAR, several different methods are used to detect range-Doppler information of the target. Compressive sensing based method is more accurate than conventional methods and shows superior performance. There are several compressive sensing algorithms for range-Doppler estimation of active sonar. The ability of each algorithm depends on algorithm type, mutual coherence of sensing matrix, and signal to noise ratio. In this paper, we compared and analyzed computational performance and accuracy of various compressive sensing algorithms for range-Doppler estimation of active sonar. The performance of OMP (Orthogonal Matching Pursuit), CoSaMP (Compressive Sampling Matching Pursuit), BPDN (CVX) (Basis Pursuit Denoising), LARS (Least Angle Regression) algorithms is respectively estimated for varying SNR (Signal to Noise Ratio), and mutual coherence. The optimal compressive sensing algorithm is presented according to the situation.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.33-38
• /
• 2012

An in-plane thermoelectric sensor was processed on a glass substrate by evaporation of the n-type Bi-Te and p-type Sb-Te thin films, and its sensing characteristics were evaluated. The n-type Bi-Te thins film used to fabricate the inplane sensor exhibited a Seebeck coefficient of -165 ${\mu}V$/K and a power factor of $80{\times}10^{-4}W/K^2-m$. The p-type Sb-Te thin film used to fabricate the in-plane sensor exhibited a Seebeck coefficient of 142 ${\mu}V$/K and a power factor of $51.7{\times}10^{-4}W/K^2-m$. The in-plane thermoelectric sensor consisting of 15 pairs of the n-type Bi-Te and the p-type Sb-Te evaporated thin films exhibited a sensitivity of 2.8 mV/K.

• Korean Journal of Materials Research
• /
• v.28 no.1
• /
• pp.32-37
• /
• 2018

We report on the efficient detection of NO gas by an all-oxide semiconductor p-n heterojunction diode structure comprised of n-type zinc oxide (ZnO) nanorods embedded in p-type copper oxide (CuO) thin film. The CuO thin film/ZnO nanorod heterostructure was fabricated by directly sputtering CuO thin film onto a vertically aligned ZnO nanorod array synthesized via a hydrothemal method. The transport behavior and NO gas sensing properties of the fabricated CuO thin film/ZnO nanorod heterostructure were charcterized and revealed that the oxide semiconductor heterojunction exhibited a definite rectifying diode-like behavior at various temperatures ranging from room temperature to $250^{\circ}C$. The NO gas sensing experiment indicated that the CuO thin film/ZnO nanorod heterostructure had a good sensing performance for the efficient detection of NO gas in the range of 2-14 ppm under the conditions of an applied bias of 2 V and a comparatively low operating temperature of $150^{\circ}C$. The NO gas sensing process in the CuO/ZnO p-n heterostructure is discussed in terms of the electronic band structure.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.10a
• /
• pp.157-157
• /
• 1997

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.89.1-89
• /
• 1998

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.727-730
• /
• 2005

In this paper, we propose a new current sense amplifier for low-voltage, high-speed SRAM. As a supply voltage is reduced, a sensing delay is increased owing to reduced cell read current. It causes a low-speed operation in SRAM. To overcome this problem, we present a new current sense amplifier which consists of the current-mirror type circuit with feedback structure. For demonstration, a 0.8-V, 256-Kb SRAM incorporating the proposed current sense amplifier has been designed with $0.18-{\mu}m$ CMOS technology. The simulation results show 15.6ns of the sensing delay reduction in comparison with a previous current sense amplifier and 11.5ns of the sensing delay reduction in comparison with a voltage sense amplifier.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.2
• /
• pp.311-320
• /
• 2001

Since 1998 for protection of marine pollution, all ships must have oil filtering equipment and 15ppm bilge alarms which satisfy Requirements of MARPOL 73/78. Oily-water separator used in machinery area of ships usually consists of two parts; one is filtering equipment and the other is oil content meter(OCM). This study presents optical characteristics of bilge were acquired form oil content sensing module. The oil content sensing module consists of IR-LED light source, photo-diode light receivers, and a glass tube for bilge water sample. The experiment with the bilge water demonstrates various valuable optical properties. These optical properties suggest notes and guides to make the low-cost, easy operation and good performance commercial type OCM that satisfy the requirements of MARPOL 73/78.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.601-603
• /
• 2005

Refocusing methods are used to compensate optical performance degradation of high resolution satellite camera during on-orbit operation. Due to mechanical vibration during launch and thermal vacuum environment of space where camera is exposed, the alignment of optical system may have error. The focusing error is dominant of misalignment and caused by the de-space error of secondary mirror of catoptric camera, which is most sensitive to vibration and space environment. The high resolution camera of SPOT, Pleiades and KOMPSAT2 have refocusing device to adjust focusing during orbital operation while QuickBird of US does not use on orbit refocusing method. For the Korsch type optical configuration which is preferred for large aperture space remote sensing camera, secondary mirror and folding mirror are available as refocusing element.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.4 s.9
• /
• pp.15-21
• /
• 2000

An anemometer employing the bulk PTC thermistor as the sensing element is investigated in this study. The numerical and experimental works are carried out to improve the sensitivity problem of the element by focusing fluid dynamics point of view. The typical shape of the sensing element has been used as a rectangular type, but this shape has a sensitivity problem because of flow separations on the sharp edge when the flow direction is different from that of the sensing element. In order to reduce the reading error, the installer has to be very careful about the flow direction. The reading error fluctuation by time as well as the sensitivity problem can be improved considerably through this study. It can be concluded that the small change of the sensor shape can improve the performance of the flow sensor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.05a
• /
• pp.142-145
• /
• 1993

$TiO_2-V_2O_5$ thin films are fabricated by Sol-Gel method and humidity sensing properties have been investigated. As the results of humidity sensing properties of thin films fabricated as humidity sensor, it is confirmed to have good humidity sensing properties in high humidity and low frequency regions.