• Archives of Pharmacal Research
• /
• 제27권1호
• /
• pp.1-12
• /
• 2004

Initial burst is one of the major challenges in protein-encapsulated microparticle systems. Since protein release during the initial stage depends mostly on the diffusional escape of the protein, major approaches to prevent the initial burst have focused on efficient encapsulation of the protein within the microparticles. For this reason, control of encapsulation efficiency and the extent of initial burst are based on common formulation parameters. The present article provides a literature review of the formulation parameters that are known to influence the two properties in the emulsion-solvent evaporation/extraction method. Physical and chemical properties of encapsulating polymers, solvent systems, polymer-drug interactions, and properties of the continuous phase are some of the influential variables. Most parameters affect encapsulation efficiency and initial burst by modifying solidification rate of the dispersed phase. In order to prevent many unfavorable events such as pore formation, drug loss, and drug migration that occur while the dispersed phase is in the semi-solid state, it is important to understand and optimize these variables.

• 한국재료학회지
• /
• 제10권2호
• /
• pp.117-123
• /
• 2000

본 연구에서는 반응고 Al합금을 얻기 위해서 3상 2극의 전자교반장치를 이용하였으며, 주입온도와 주입전압을 변화시켜 Al합금의 초정입자크기, aspect ratio, 표준편차, 경도 및 공정 Si 입자의 크기 및 형상 변화를 조사하였다. 같은 주입온도에서는 주입전압이 증가함에 따라 aspect ratio, 표준편차 및 초정입자의 크기는 감소되었다. 전자교반식 수평연속주조방법에 의한 Al 합금의 최적제조 조건은 주입전압 220V, 주입온도 68$0^{\circ}C$이었으며, 이 조건에서 초정입자의 크기는 54$\mu\textrm{m}$이었고, aspect ratio는 1.56이었으며 그 표준편차는 0.4이었다. 그리고 공정 Si의 크기는 0.5$\mu\textrm{m}$이었으며 제조된 Al합금의 경도는 72.1 Hv를 나타내었다. 본 연구를 위해 제작된 3상 2극 전자교반장치에 의해서 매우 낮은 aspect ratio 및 표준편자를 갖는 반응고 A356 Al합금을 제조할 수 있었다.

• 분석과학
• /
• 제7권4호
• /
• pp.441-453
• /
• 1994

수질에서 유해물질을 농축하는 방법으로 액체 추출법과 고체상 추출법을 GC/MS를 검출기로 사용하여 비교하였다. 비휘발성 유해물질 중 11종의 산과 44종의 염기/중성 화합물들을 reagent water에 첨가하여 분석한 결과, 액체추출법은 54종의 화합물에 대해 91%의 평균회수율과 4.6%의 평균상대표준편차를 나타내었으며, 고체상 추출법은 52종의 화합물에 대해 63%의 평균회수율과 8.9%의 평균상대표준편차를 보였다. 두 방법의 검출한계는 $1{\sim}5{\mu}g/l$였다.

• 한국물환경학회지
• /
• 제22권5호
• /
• pp.879-886
• /
• 2006

The analytical methods of polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans (PCDD/Fs) for water sample with extremely low concentration was developed to extract large volume and to improve fast chromatography for clean up. Semi-automated solid phase extraction (SPE) system and column coupling chromatography using elution pump was optimized and applied to each processes of treatment plant. Results of disk type SPE indicated that this system was applicable below 40 L of aqueous sample with a flow rate of 0.08 ~ 0.2 L/min. Average recoveries of SPE using labeled sampling spike of $^{37}Cl$-2,3,7,8-TCDD was 97%. Column coupling method resulted in reduced clean up time, solvent volume, increased average recoveries with constant elution rate. The combined methods were applied to the monitoring of drinking water treatment plant. Limits of detection (LOD) of each process were calculated. For example, LOD of raw and treated water ranged 0.094~0.968 pg/L and 0.028~0.364 pg/L, respectively. Combined methods of extraction and cleanup techniques provided fast analysis of PCDD/Fs with high accuracy and low LODs for water samples.

• 소성∙가공
• /
• 제14권4호
• /
• pp.319-326
• /
• 2005

In this study, the nano-deformation behavior of semi-solid Al-Si alloy was investigated using a molecular dynamics simulation as a part of the research on the surface crack behavior in thixoformed automobile parts. The microstructure of the grain-size controlled Al-Si alloy consists of primary and eutectic regions. In eutectic regions the crack initiation begins with initial fracture of the eutectic silicon particles and inside other intermetallic phases. Nano-deformation characteristics in the eutectic and primary phase of the grain-size controlled Al-Si alloy were investigated through the molecular dynamics simulation. The primary phase was assumed to be single crystal aluminum. It was shown that the vacancy occurred at the zone where silicon molecules were.

• 신재생에너지
• /
• 제18권2호
• /
• pp.40-49
• /
• 2022

In this study, the phase and electrochemical properties of Co and Ti substituted layered perovskites SmBaCo_2-xTi_xO_5+d (x=0.5, 0.7, 1.0, 1.1, 1.3, and 1.5) were analyzed, and their application as electrodes in solid oxide fuel cells (SOFCs) were evaluated. After calcination at 1300℃ for 6 h, a single phase was observed for two compositions of the SmBaCo_2-xTi_xO_5+d oxide system, SmBaCoTiO_5+d (x=1.0) and SmBaCo_0.9Ti_1.1O_5+d (x=1.1). However, the phases of SmBaCoTiO_5+d (SBCTO) and SmTiO₃ coexisted for compositions with x≥1.3 (Ti content). In contrast, for compositions of x≤0.7, the SmBaCo₂O_5+d phase was observed instead of the SmTiO₃ phase. To evaluate the applicability of these materials as SOFC electrodes, the electrical conductivities were measured under various atmospheres (air, N₂, and H₂). SBCTO exhibited stable semi-conductor electrical conductivity behavior in an air and N₂ atmosphere. However, SBCTO showed insulator behavior at temperatures above 600℃ in a H₂ atmosphere. Therefore, SBCTO may only be used as cathode materials. Moreover, SBCTO had an area specific resistance (ASR) value of 0.140 Ω·cm² at 750℃.

• 분석과학
• /
• 제33권1호
• /
• pp.11-22
• /
• 2020

When extracting semi-volatile components of herbal medicines using hot water vapor, some substances may react with water vapor or oxygen, and some volatile substances may be lost, when using an organic solvent extraction method has the disadvantage that it may contain a non-volatile material and residual organic solvent. In addition, it is inefficient to separate semi-volatile substances from herbal medicines into each single component and conduct biological activity research for each component to determine the effective ingredient, and some components may be lost in the separation process. In this study, semi-volatile substances evaporated under two pressure-reduced conditions in Chinese herbal medicines such as Cnidii Rhizoma, Aucklandiae Radix and Amomum Fructus were separated by cooling with liquid nitrogen. Those were analyzed by gas chromatography-mass spectrometry (GC-MS) to identify the components, and this method may be used to study biological activities at the cellular level. The substances separated under reduced pressure, essential oil obtained by simultaneous distillation extraction (SDE) method and substances by using solid phase micro-extraction (SPME) from Cnidii Rhizoma, Aucklandiae Radix and Amomum Fructus were analyzed by GC-MS. In the case of Cnidii Rhizoma and Aucklandiae Radix, there were some differences among the essential oil components obtained by SDE and those identified by low temperature capture (CT) and SPME method, these were believed to be produced by some volatiles reacting with water or oxygen at the boiling point temperature of water.

• 대한화장품학회지
• /
• 제41권3호
• /
• pp.201-208
• /
• 2015

오가노겔은 반고형상이며 3차원의 네트워크 구조로 이루어진 친유성 용매로 이루어져 있다. 본 연구에서는 유상과 수상에서 모두 난용성 특징을 가진 제니스테인을 포함하는 레시틴 오가노겔을 개발하였다. 이 시스템은 안정할 뿐만 아니라 경피 흡수 실험에서도 높은 흡수율을 보였다. 본 오가노겔 제형에 적합한 원료들을 선별한 결과, 수화된 레시틴, 해바라기유, dipropylene glycol (DPG), polyethylene glycol (PEG)이 이 시스템에서 주로 사용되었다. 레시틴 오가노겔의 제조에 적합한 원료의 함량은 phase ternary diagram 작성을 통하여 결정하였다. 제조된 레시틴 오가노겔을 organoleptic characteristics, stability, pH, rheology, phase transition temperatures, microscopic analysis, skin penetration 실험을 통해 평가하였다. 본 연구 결과를 통해 본 논문에서 제시하는 레시틴 오가노겔 제형은 안정한 상태에서 난용성 물질을 높은 농도로 피부에 효과적으로 전달할 수 있는 제형으로 활용될 수 있을 것이라 생각된다.

• 한국주조공학회지
• /
• 제21권4호
• /
• pp.232-238
• /
• 2001

Experimental study on the twin roll strip casting of BCuP-5(Cu-15wt%Ag-wt5%P) alloy was carried out using laboratory scale horizontal type twin roll caster. In this study, among the various operating parameters, such as tundish angle, contact angle, pouring temperature, roll speed, presetting gap of the rolls and kinds of roll and tundish materials, effect of pouring temperature for strip casting of BCuP-5 alloy which has long freezing range of about $170^{\circ}C$ was mainly investigated. BCuP-5 alloy strip was successfully produced when pouring molten metal at lower temperature than its liquidus temperature. Microstructure of the cast strip consists of primary Cu and eutectic. Especially the size of primary Cu phase increased with decreasing of pouring temperature.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 추계학술발표회논문집(1)
• /
• pp.617-624
• /
• 1997

This Paper Presents an effective and simple procedure for the simulation of the motion of the solid-liquid interfacial boundary and the transient temperature field during phase change process. To accomplish this purpose, an iterative implicit solution algorithm has been developed by employing the dual reciprocity boundary element method. The dual reciprocity boundary element approach provided in this paper is much simpler than the usual boundary element method applying a reciprocity principle and an available technique for dealing with domain integral of boundary element formulation simultaneously. The effectiveness of the present analysis method have been illustrated through comparisons of the calculation results of an example with its semi-analytical or other numerical solutions where available.