• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.207-214
• /
• 2002

Nano adhesion between SPM (scanning probe microscope) tips and $DDPO_{4}$ (dodecylphosphoric acid ester) and $ODPO_{4}$ (octadecylphosphoric acid ester) SAM (self-assembled monolayer) was experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM(atomic force microscope) and LFM(lateral force microscope) modes with the applied normal load. $DDPO_{4}$ and $ODPO_{4}$ SAM were formed on TiMe and TiOx surfaces. TiMe and TiOx were coated on the Si wafer by ion sputtering. Adhesion and friction of $DDPO_{4}$ and $ODPO_{4}$ SAM surfaces were compared with those of OTS (octadecyltrichlorosilane) SAM and DLC surfaces. $DDPO_{4}$ and $ODPO_{4}$ SAM converted the TiMe and TiOx surfaces to be hydrophobic. When the surface was hydrophobic, the adhesion and friction forces were found lower than those of bare surfaces. Work of adhesion was also discussed to explain how the surface was converted into hydrophobic. Results also showed that tribological characteristics of $DDPO_{4}$ and $ODPO_{4}$ had good properties in the adhesion, friction, wetting angle and work of adhesion. $DDPO_{4}$ and $ODPO_{4}$ SAM could be one of the candidates for the bio-MEMS elements.

• Tribology and Lubricants
• /
• v.24 no.2
• /
• pp.63-71
• /
• 2008

Friction and adhesion tests were conducted to investigate tribological characteristics of materials for MEMS/NEMS using atomic force microscope (AFM). AFM Si tips were chemically modified with a self-assembled monolayer (SAM) derived from trichlorosilane like octadecyltrichlorosilane (OTS) and (1H, 1H, 2H, 2H-perfluorooctyl) trichlorosilane (FOTS), and various materials, such as Si, Al, Au, Cu, Ti and PMMA films, were prepared for the tests. SAMs were coated on Si wafer by dipping method prior to AFM tip to determine a proper dipping time. The proper dipping time was determined from the measurements of contact angle, surface energy and thickness of the SAMs. AFM tips were then coated with SAMs by using the same coating condition. Friction and adhesion forces between the AFM Si tip modified with SAM and MEMS/NEMS materials were measured. These forces were compared to those when AFM tip was uncoated. According to the results, after coating OTS and FOTS, the friction and adhesion forces on all materials used in the tests decreased; however, the effect of SAM on the reduction of friction and adhesion forces could be changed according to counterpart materials. OTS was the most effective to reduce the friction and adhesion forces when counterpart material was Cu film. In case of FOTS, friction and adhesion forces decreased the most effectively on Au films.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.1
• /
• pp.1-6
• /
• 2007

Mercaptopropionic acid(mpa) has been used to make self-assembled monolayer(SAMs) on the surface of graphite electrode incorporating gold nano particles, which are subsequently modified with dopamine(dopa). Such modified electrodes haying types of Gr(Au)/mpa-dopa were employed in the electrocatalytic oxidation of NADH. The responses of such modified electrodes were studied in terms of electron transfer kinetics and reaction procedure in the reaction. The reaction of the surface immobilized dopa with NADH was studied using the rotating disk electrode technique and a value of $5.06{\times}10^5M^{-1}s^{-1}$ was obtained for the second-order rate constant in 0.1 M phosphate buffer(pH=7.0), which was a $EC_{cat}$ and kinetic controlled procedure. But, the modified electrodes were diffusion controlled reaction having $4.64{\times}10^{-4}cm^2s^{-1}$ of the coefficient within $10^{-3}s$ after starting the reaction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.841-845
• /
• 2013

We give a textured front on silicon wafer for high-efficiency solar cells by using micro contact printing method which uses PDMS (polydimethylsiloxane) silicon rubber as a stamp and SAM (self assembled monolayer)s as an ink. A random pyramidal texturing have been widely used for a front-surface texturing in low cost manufacturing line although the cell with random pyramids on front surface shows relatively low efficiency than the cell with inverted pyramids patterned by normal optical lithography. In the past two decades, the micro contact printing has been intensively studied in nano technology field for high resolution patterns on silicon wafer. However, this promising printing technique has surprisingly never applied so far to silicon based solar cell industry despite their simplicity of process and attractive aspects in terms of cost competitiveness. We employ a MHA (16-mercaptohexadecanoic acid) as an ink for Au deposited $SiO_2/Si$ substrate. The $SiO_2$ pattern which is same as the pattern printed by SAM ink on Au surface and later acts as a hard resist for anisotropic silicon etching was made by HF solution, and then inverted pyramidal pattern is formed after anisotropic wet etching. We compare three textured surface with different morphology (random texture, random pyramids and inverted pyramids) and then different geometry of inverted pyramid arrays in terms of reflectivity.

• Journal of Sensor Science and Technology
• /
• v.19 no.6
• /
• pp.456-461
• /
• 2010

The detection of C-reactive protein(CRP) using self-assembled monolayer(SAM) was investigated by a portable surface plasmon resonance(SPR) sensor system. The CRP is a biomarker for the possible cardiovascular disease. The SAM was formed on gold(Au) surface to anchor the monoclonal antibody of CRP(anti-CRP) for detection of CRP. Sequence injection of the anti-CRP and bovine serum albumin(BSA) into the sensor system has been carried out immobilize the antibody and to prevent non-specific binding. The portable SPR system has two flow channels: one for the sample measurements and the other for the reference. The output SPR signal was increased with the injection of the anti-CRP, BSA and CRP due to binding of the proteins on the sensor chip. The valid output SPR signals was linearly related to the critical range of the CRP concentration. The experimental results showed the feasibility of the portable SPR system with newly developed SAM to diagnose a risk of the future cardiovascular events.

• Journal of Sensor Science and Technology
• /
• v.15 no.4
• /
• pp.237-244
• /
• 2006

Atomic force microscope (AFM) has become a common tool for the structural and physical studies of biological macromolecules, mainly because it provides the ability to perform experiments with samples in a buffer solution. In this study, structure of proteins and nucleic acids has been studied in their physiological environment that allows native intermolecular complexes to be formed. Cr and Au were deposited on p-Si (100) substrate by thermal evaporation method in sequence with the thickness of $200{\AA}$ and $500{\AA}$, respectively, since Au is adequate for immobilizing biomolecules by forming a self-assembled monolayer (SAM) with semiconductor-based biosensors. The SAM, streptavidin and biotin interacted each other with their specific binding energy and their adsorption was analyzed using the Bio-AFM both in a solution and under air environment. A silicon nitride tip was used as a contact tip of Bio-AFM measurement in a solution and an antimony doped silicon tip as a tapping tip under air environment. Actual morphology could also be obtained by 3-dimensional AFM images. The length and agglomerate size of biomolecules was measured in stages. Furthermore, $R_{a}$ (average of surface roughness) and $R_{ms}$ (mean square of surface roughness) and surface density for the adsorbed surface were also calculated from the AFM image.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.354-359
• /
• 2006

Recently, the interest in lithography without photo exposure has been increased compare to the conventional photolithography in nano meter and micrometer size patterning area. We studied a self aligned dipping of Ag solution through micro contact printing (${\mu}-CP$) with octadecyltrichlorosilane (OTS) treated polydimethylsiloxane (PDMS) soft mold. The OTS monolayer on the patterned PDMS was formed by dipping it into OTS solution. We transferred the OTS monolayer from PDMS mold to the glass. The OTS monolayer changed the surface energy from hydrophilic surface to hydrophobic surface, And then we made self aligned Ag solution patterns just after dipping the substrate, using adhesion difference of Ag solution between OTS treated hydrophobic area and non-OTS treated hydrophilic area. We finally get the Ag patterns through only dip-coating after the ${\mu}-CP$ process. And we observed surface energies on the glass substrate through the contact angle measurements as time goes on.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.91-92
• /
• 2006

The electrical properties of viologen derivatives were studied in terms of the tunneling current characteristics on the length of the viologen derivatives using self-assembling techniques and ultra high vacuum scanning tunneling microscopy (UHV-STM). We fabricated the Au substrate were deposited by thermal evaporation system ($420^{\circ}C$. Self-assembled monolayers (SAMs) were prepared on Au (111), which had been thermally deposited onto freshly cleaved, heated mica. The Au substrate was exposed to a 1 mM solution of viologen derivatives in ethanol for 24 hours to form a monolayer. We measurement of the morphology on the single viologen molecules ($VC_{8}SH$, $VC_{10}SH$, $HSC_{8}VC_{8}SH$, and $HSC_{10}VC_{10}SH$). The current-voltage (I-V) and differential conductance (dl/dV-V) properties were measured while the electrical properties of the formed monolayer were scanned by using a STS. The effective barrier height of viologen derivatives ($VC_{8}SH$, $VC_{10}SH$, $HSC_{8}VC_{8}SH$, and $HSC_{10}VC_{10}SH$) were calculated to be 1.076 eV, 1.56 ${\pm}$ 0.3 eV, 1.85 eV, 2.28 eV, respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.12 no.3
• /
• pp.7-11
• /
• 2010

For many large-scale applications of high-temperature superconducting materials, large critical current density($J_c$) in high applied magnetic fields are required. A number of methods have been reported to introduce artificial pinning centers(APCs) in $YBa_2Cu_3O_{7-\delta}$(YBCO) films for enhancement of their $J_c$. In this work, we investigated electric characteristic of YBCO films on $SrTiO_3$ (100) substrates whose surfaces were modified by the introduction of Au nanoparticles (AuNPs). Au nanoparticles were uniformly dispersed on STO substrates with one of typical solution techniques, self assembled monolayer. After heating the STO substrates with Au nanoparticles, the size of Au nanoparticles was around 29~32 nm in height and 41~49 nm in diameter. XRD diffraction patterns taken on the YBCO film with Au nanoparticles show the c-axis orientation. The measured $T_c$ of YBCO /AuNPs films was around 89K and the $J_c$ was 0.75 MA/$cm^2$ at 65 K and 1 T.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.1
• /
• pp.127-130
• /
• 2005

The early stage of the self assembly for octadecyltrichlorosilane (OTS)-based monolayers is investigated using atomic force microscopy (AFM). Height measurements using AFM prove that the island height of the monolayers gradually increases with increasing the island size, and is close to the limiting value (h = $\sim$25 $\AA$) after d = $\sim$600 nm in size. Since the theoretical length of a covalently bound OTS molecule is 26.2 Å, the limiting value of the island height means that the islands with d ${\geq}$ 600 nm consist of close-packed, fully extended chains. The heights for the islands with d < 600 nm are lower than the limiting value and decrease with decreasing the island sizes. This observation indicates that the OTS molecules in the small islands are less densely packed, and that the packing densities of the islands increase as the islands grow in size.