• Journal of the Korean Solar Energy Society
• /
• v.29 no.6
• /
• pp.110-118
• /
• 2009

This research is an experimental study on BIPV Power performance of See-through a-si and Light-through applying external curtain wall. In case of See-through a-si Photovoltaic, appropriateness of facade applying standard($950\;{\times}\;980mm$) large($950\;{\times}\;1960mm$)area photovoltaic was examined. Transparent performance was also investigated through Power simulation according to angles and seasons of See-through a-si and Light-through Photovoltaic so that Power output was surveyed with using designed and manufactured Mock-up. When comparing See-through a-si to Light-through Photovoltaic for simulation Power output on angles based on full south aspect, which the result was that See-through a-si Power output according to Light-through Power output was the highest of 65.5% when applying a 90 degree angle. Monthly accumulated average Power output during winter seasons (December, January and February) applying a vertical plane on full south aspect was analyzed, which results in 66.37W/h of See-through a-si and 139.1 W/h of Light-through. See-through a-si Power output showed 47.7% in comparison with Light-through transparent. Also monthly, hourly average Power efficiency according to solar radiation during winter seasons (December, January and February) was that 4.7% of See-Through a-si and 9.8% of Light-through.

• Current Photovoltaic Research
• /
• v.11 no.4
• /
• pp.114-117
• /
• 2023

Transparent Photovoltaic (PV) modules have recently been in the spotlight because they can be applied to buildings and vehicles. However, crystalline silicon (c-Si) solar modules, which account for about 90% of the PV module market, have the disadvantage of applying transparent PV modules due to their unique opacity. Recently, a see-through type PV module using a crystalline silicon solar strap has been developed. However, there is a problem due to a decrease in aesthetics due to the metal ribbon in the center of the see-through type PV module and difficulty bonding the metal ribbon due to the low voltage output of the strap. In this study, to solve this problem, we developed a fabrication process of series connected c-Si solar strap cells using the c-Si solar cells. We succeeded in fabricating a series connected strap with a width of 2-10 mm, and we plan to manufacture an aesthetic see-through type c-Si PV module.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.1
• /
• pp.1-10
• /
• 2009

This study was carried out to evaluate the Life Cycle Cost(LCC) of three types of RTPV(Building Integrated Photovoltaic) systems-Glass plus Granite. Crystalline BIPV and See through Amorphous BIPV-which were vertically installed to generate the same power output(76 kW level). Initial investment costs. cost. savings and maintenance costs had been predicted during the period of analysing the LCC of three types of BIPV(Building Integrated Photovoltaic) systems installed for the purpose of evaluating the LCC. In case of cost savings, it had been analyzed by measuring the amount of electric power generated, reduction in lighting load and heat & cooling loads through simulation. From this analysis, it was predicted that the See-through amorphous BIPV offering cost saving advantages demonstrated the economical efficiency similar to the Class plus Granite when it is backed by more than 20 years of durability.

• Current Photovoltaic Research
• /
• v.3 no.3
• /
• pp.80-84
• /
• 2015

We suggest new emitter formation method using solid-phase epitaxy (SPE); solid-phase epitaxy emitter (SEE). This method expect simplification and cost reduction of process compared with furnace process (POCl3 or BBr3). The solid-phase epitaxy emitter (SEE) deposited a-Si:H layer by radio-frequency plasma-enhanced chemical vapor deposition (RF-PECVD) on substrate (c-Si), then thin layer growth solid-phase epitaxy (SPE) using rapid thermal process (RTP). This is possible in various emitter profile formation through dopant gas ($PH_3$) control at deposited a-Si:H layer. We fabricated solar cell to apply solid-phase epitaxy emitter (SEE). Its performance have an effect on crystallinity of phase transition layer (a-Si to c-Si). We confirmed crystallinity of this with a-Si:H layer thickness and annealing temperature by using raman spectroscopy, spectroscopic ellipsometry and transmission electron microscope. The crystallinity is excellent as the thickness of a-Si layer is thin (~50 nm) and annealing temperature is high (<$900^{\circ}C$). We fabricated a 16.7% solid-phase epitaxy emitter (SEE) cell. We anticipate its performance improvement applying thin tunnel oxide (<2nm).

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.108-108
• /
• 2011

공동주택에서 2025년 정부가 추진하고 있는 Zero Energy 건축물 구현과 친환경에 대한 탄소배출 저감 문제로 재생에너지 생산시스템의 추가 적용은 반드시 필요하다. 따라서 공동주택 적용 및 활용성을 높일 수 있는 BIPV시스템 개발을 통하여 설치면적 확보와 세대 활용성을 높일 수 있도록 하는 것이 필요하다. 특히 거실 창호의 경우 주방향이 남향, 남동 또는 남서향으로 배치되어 태양광을 적용하기에 적합한 특성을 가지고 있다. 그러나 창호는 건물외피의 역할과 재실자가 조망과 정보취득을 얻을 수 있는 중요한 통로가 되기 때문에 단열 문제나 시야 차폐의 문제는 발생하지는 않도록 하는 것이 필요하다. 본 연구에서는 a-si타입 모듈 2개를 10% 투과율로 Bsck Coating 색상을 달리한 모듈과 c-si BIPV 모듈을 커튼월 창호시스템으로 개발, 일반 2중 창호시스템과 비교 평가를 위해 실제 Test bed 건물에 시공하여 시환경 및 실내 창측면 온도변화 측정 분석을 진행하였다. 현재 국내외 출시되고 있는 a-si see through 모듈은 10~30%의 투과율로 창 마감재로 대체가 가능하나 건축 환경(시환경,열환경)에 대한 분석은 전무한 상태이다. 본 연구에서는 시환경과 창유리면의 열 부하, 자외선, 적외선 차폐 및 가시광선의 투과율에 대한 평가와 Back Coating에 따른 색온도 평가를 통해서 a-si BIPV의 공동주택 세대 발코니 창호 적합성에 대한 검토를 진행하였다. 연구결과는 아래와 같다. ${\bullet}$ 실내조도는 청천공 정오기준 가시성 확보 모듈의 경우 2,300 ~ 3,500lx를 나타내고 있어 대비 현상이나 창측의 급격한 조도 변화가 적은 시환경 구축이 가능 ${\bullet}$ 12시경 휘도는 창측면, 실내 벽체, 코너 바닥면을 대상으로 a-si BIPV 모듈을 적용한 경우 휘도비가 12:1로 KS나 IESNA의 광원과 근접면의 비 20:1 범위에 모두 존재, 적합한 것으로 분석되었으나 c-si의 경우는 그림자로 인한 대비 현상이 발생, 작업 시환경 문제 발생. ${\bullet}$ 이중시스템 창호와 비교하여 단열 성능 떨어짐. 발전시간대 창유리 면 온도 상승 으로 하절기 냉방부하 증가. ${\bullet}$ 자외선은 100% 가까이 차단, 적외선은 13~42%만 투과되고 가시광선은 13% 투과율을 나타내어 일반 창에 칼라 코팅을 적용하는 것과 유사한 경향을 나타냄.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1145-1148
• /
• 2008

The present status and trend of oxide phosphor thin-film development for thin-film electroluminescent (TFEL) device application are presented in this paper. Recently, several newly developed types of bendable or bendable see-through oxide TFEL lamps have been fabricated using the TFEL technology with a newly developed bendable ceramic sheet, glass sheet or sapphire sheet substrate, which has become available on the market. Stable operation at high temperatures was obtained in double-insulating-layer-type TFEL lamps fabricated with a $Zn_2Si_{0.6}Ge_{0.}4O_4$:Mn thin-film emitting layer forming on translucent or transparent bendable sheet substrates.

• Current Photovoltaic Research
• /
• v.5 no.1
• /
• pp.33-37
• /
• 2017

Today, photovoltaic power generation mostly uses Si crystalline solar cell modules. The most vulnerable part of the Si solar cell module is that the power generation decreases due to the temperature rise. But, it is widely used because of low installation cost. In the solar market, where Si crystalline solar cell modules are widely used. The CPV (Concentrated Photovoltaic) module appeared in the solar market. The CPV module reduces the manufacturing cost of the solar cell by using non-Si in the solar cell. Also, there is an advantage that a rise in temperature does not cause a drop in power generation. But this requires high technology to install and has a disadvantage that the initial installation cost is expensive compared to normal Si solar cell module. So that we built a testbed to see these characteristics. The testbed was used to measure the amount of power generation in a long-term outdoor environment and compared with the general Si solar cell module.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.12
• /
• pp.761-767
• /
• 1999

Poly-Si TFTs(polycrystalline silicon thin film transistors) fabricated on a low cost glass substrate have attracted a considerable amount of attention for pixel elements and peripheral driving circuits in AMLCS(active matrix liquid crystal display). In order to apply poly-Si TFTs for high resolution AMLCD, a high operating frequency and reliable circuit performances are desired. A new poly-Si TFT with CLBT(counter doped lateral body terminal) is proposed and fabricated to suppress kink effects and to improve the device stability. And this proposed device with BC(buried channel) is fabricated to increase ON-current and operating frequency. Although the troublesome LDD structure is not used in the proposed device, a low OFF-current is successfully obtained by removing the minority carrier through the CLBT. We have measured the dynamic properties of the poly-Si TFT device and its circuit. The reliability of the TFTs and their circuits after AC stress are also discussed in our paper. Our experimental results show that the BC enables the device to have high mobility and switching frequency (33MHz at $V_{DD}$ = 15 V). The minority carrier elimination of the CLBT suppresses kink effects and makes for superb dynamic reliability of the CMOS circuit. We have analyzed the mechanism in order to see why the ring oscillators do not operate by analyzing AC stressed device characteristics.

• Korean Journal of Oriental Medicine
• /
• v.9 no.1
• /
• pp.1-33
• /
• 2003

From the study on Doo-Jong Kims view of history about the early Korea$(Korea\;herewith\;stands\;for\;Korea\;dynasty\;A.D.918{\sim}1392)s$ Medicine, I came to a conclusion as follows. 1. Doo-Jong Kim is stressing on the fact that Early Koreas Medicine inherited from Shilla dynasty and seemingly expressing the pride of national medical science. But actually he distorted the Koreas independent growth with flunkeyism and insisted that Koreas medicine only took over Shilla dynastys which based on Chinese Tang dynastys medical science. As a result, Koreas medicine was blurred and evaluated as nothing but Tangs medicine. But, the reasons of Doo-Jong Kims viewpoints were not based on the fact, but on his speculation. 2. About the medical system, Doo-Jong Kim viewed that Korea copied Chinese Soo & Tangs medical system, But the fact is that Korea only borrowed a part of Chinese medical systems name, for examples, Tae-I-Gam, Sang-Yak-Kook, Sang-Sik-Kook, etc., and its actual functions were different and grew in Koreas own way, As a result, the titles or roles in the system were very different from those of Chinas. Especially, Korea saw much development in Science of Acupuncture and Moxibustion that there was a specialist on Acupuncture, called I-Chim-Sa, and even had much influences on Chinese Acupuncture and Moxibustions growth, exporting Hwang-Je-Ne-Kyong to Chinese Song dynasty. 3. About the education system of medicine, Doo-Jong Kim viewed that Koreas medicine was only a copy of Shilla dynastys which was based on Chinese Tang dynastys, taking the medical examination curriculum as an example. The fact is that Tangs medical curriculum was three, Bon-Cho, Kab-Ul, Maek-Kyong, Shilla had seven, Bon-Cho-Kyong, Kab-Ul-Kyong, So-Moon-Kyong, Chim-Kyong, Maek-Kyong, Myong-Dang-Kyong, Nan-Kyong, and Korea had ten, So-Moon-Kyong, Kab-Ul-Kyong, Bon-Cho-Kyong, Myong-Dang-Kyong, Maek-Kyong, Dae-Kyong-Chim-Kyong, Nan-Kyong, Ku-Kyong, Ryu-Yon-Ja-Bang, So-Kyong-Chang-Jeo-Ron. Simply considering this, it is so clear that Koreas medical curriculum was much more upgraded one than that of China. 4. About the examination system for civil service, Doo-Jong Kim expressed that Shilla dynasty did not have such system, and only expounded knowledge of Shilla medicine, In case of China, Tang danasty Hyang-Kong was only a qualification test for civil service, which the result was completely dependent on applicants social status, Song danasty examination system was composed of three steps of Hyang-Si, Sung-Si, Jeon-Si (See Note1), but it stuck to formality by having Jeon-Si of anti-fraudulence use. On the other hand, examination system for civil service in Korea dynasty started in 958 by an advice of Ssang-Ki, Chin-Si in 977 and K대-Ja-Si (See Note 1), a kind of Hyang-Si, in 1024., Three steps of examination system made employment for civil service strictly fair, Moreover, it was possible for offsprings of concubine to be an applicant. These easily explain that the examination system of Korea dynasty was more upgraded one than that of China, Tang ＆ Song dynasty. Hyang-Si : Exam in local area Sung-Si : Exam in province for those who passed Hyang-Si Jeon-Si : Exam held with Koea Kings supervision for those who passed Hyang-Si Keo-Ja-Si : Selective exam in local area like Hyang-Si. From the reasons above, it is clear that Doo-Jong Kim was much biased by flunkeyism through Japanese colonialisam and expressed his view on Korea Medical History based on such theory of heteronomy and stasis. Moreover, without rigid historical evidence on records, he distored the fact by translating incorrectly on his purpose. Therefore, Doo-Jong Kims Korean Medical History must be reevaluated through rigid historical research and his mistranslation should be corrected.

• Journal of the Korean Home Economics Association
• /
• v.18 no.4
• /
• pp.41-45
• /
• 1980

We must identify the forms of dress devised throughout ages, when we wtudy, interpret and analyze the numerous resource material of costume. The study which depends on reference to actual artifacts is necessarily limited. Whereas items of contemporary dress are readily available, much from earlier eras has been destroyed or has deteriorated through time. Such as cottons, linens, silks, wools, leathers and furs are perishable organic materials. Few garments dated earlier than seventeenth century has survived except armor, jewelry. We have many sources of the information are available to study on costume of earlier eras. These sources are wall paintings, sculptures, painting, monumental brasses, manuscript illustration ceramics, coins, medals, mosaics, archives, literature. Wall painting and frescoes provided an useful source for costume study. Many wall paintings and frescoes were destroyed, were changed in color. It si advisable to interpret the dress detail, form color carefully. Sculpture would be useful to see the back and side views of dress. One of the most important points which should be made abut the use of sculpture as a source for costume study in early periods is that the sculptor's style will often change the character of a costume. As the painting si two-dimensional evidence for a three-dimensional costume, paintings must be accurately studied. What we must do, as far as we can, is to look at all visual representations in the light of other contemporary evidence in order to interpret the information correctly.