• ALGAE
• /
• v.27 no.2
• /
• pp.115-123
• /
• 2012

The establishment of algal spores plays an essential role in adult kelp distribution and abundance patterns. Sedimentation is a key variable regulating algal spore settlement and success, possibly controlling species-specific dominance $in$ $situ$. Laboratory experiments were used to determine spore attachment and survival rates of two Alaskan canopy-forming kelps, $Nereocystis$ $luetkeana$ (K. Mertens) Postels & Ruprecht and $Eualaria$ $fistulosa$ (Postels & Ruprecht) M. J. Wynne, to various types of sediment loading. Spore attachment for both species was significantly and similarly affected by three sediment treatments: suspended particles; settled sediment covering the substratum; and smothering of attached spores by settling sediment. Spore attachment decreased by approximately 90% at 420 mg sediment $L^{-1}$, the highest sediment load tested here, under all three treatments for both species. These results suggest that increases in sedimentation may constrain the success of the spore stages, but sediment does not seem to be a likely factor explaining species-specific distribution patterns. However, while sedimentation affected spores of both species similarly, timing of spore release in relation to times of maximum sediment load in the water might differ for different species, possibly explaining kelp species distribution patterns.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.644-653
• /
• 2018

Landslides occur frequently due to the effects of heavy rainfall and typhoons caused by climate change. Erosion control measures are needed to effectively prevent landslide damage. In order to improve their efficiency, it is necessary to quantitatively measure the sediment discharge from the mountain stream. In this study, a load cell sensor was installed in a mountain stream and the measured values were compared according to the applicability and load test type in the mountain stream. The result of the load test showed that the effect of the loading type (load test 1, 2) was low at average (loadings) of 0.4kgf and 0.6kgf at sites 1 and 2, respectively. The load factor was also derived by regression analysis to increase the accuracy of the measured values. According to the results of the load factor (normalized) to the load-cell measurement value, the output value increased by 14.8% and 24.6% in sites 1 and 2, respectively, and was calculated to be similar to the reference value. The load cell sensor enabled us to quantitatively estimate the amount of sediment discharge in the mountain stream through time series analysis with the water level and rainfall information. If the monitoring is carried out for a long time, it can be used to find the sediment discharge mechanism for the mountain stream. In addition, applying sensors such as load-cells to a mountain stream is expected to contribute to the development of related industries, such as the manufacturing of measurement sensors.

• Journal of Industrial Technology
• /
• v.28 no.B
• /
• pp.175-183
• /
• 2008

This study reviewed and compared the measured value with the calculated sediment loads value by the existing theory equation, after actually measuring the suspended load, focusing on locality river in Gangwon province. Next, it suggested the application problems of the existing sediment loads calculation equation in case of rivers in Gangwon province, and suggested the proper sediment loads calculation equation to rivers in Gangwon province, after implementing the statistical regression analysis by using the measured data for 5 rears, 2003 ~ 2007.

• Journal of Environmental Science International
• /
• v.9 no.1
• /
• pp.35-42
• /
• 2000

In this study, the movable bed model testing was carried out so as to analyze bed profile changes including predicting scouring and deposition of bed profile and to solve hydraulic problems affecting with bed and both-bank between upstream and downstream of intake weir in the Nakdong river channel. The movable bed model testing consists of fundamental test, movable model test and numerical analysis method respectively. The fundamental test was enforced to analyze relationship of discharge and sediment load in the tilting flume. When the movable model test was worked, it was shown that sediment budget between input sediment load and output sediment load was balanced exactly. As a result of movable model test, it was presented that scouring and deposition changes in quantities between the upstream and downstream of modification weir were less than those of nature and planning weir. Finally, numerical analysis method was operated by 1-dimensional bed profile changes model ; HEC-6 model so as to complement unsolving hard problems during movable model test. So, modification weir will sustained the stable bed profile changes than any other weirs in the study channel.

• Ocean Systems Engineering
• /
• v.6 no.1
• /
• pp.61-97
• /
• 2016

This is the second of two papers on the 3D numerical modeling of nearshore hydro- and morphodynamics. In Part I, the focus was on surf and swash zone hydrodynamics in the cross-shore and longshore directions. Here, we consider nearshore processes with an emphasis on the effects of oceanic forcing and beach characteristics on sediment transport in the cross- and longshore directions, as well as on foreshore bathymetry changes. The Delft3D and XBeach models were used with four turbulence closures (viz., ${\kappa}-{\varepsilon}$, ${\kappa}-L$, ATM and H-LES) to solve the 3D Navier-Stokes equations for incompressible flow as well as the beach morphology. The sediment transport module simulates both bed load and suspended load transport of non-cohesive sediments. Twenty sets of numerical experiments combining nine control parameters under a range of bed characteristics and incident wave and tidal conditions were simulated. For each case, the general morphological response in shore-normal and shore-parallel directions was presented. Numerical results showed that the ${\kappa}-{\varepsilon}$ and H-LES closure models yield similar results that are in better agreement with existing morphodynamic observations than the results of the other turbulence models. The simulations showed that wave forcing drives a sediment circulation pattern that results in bar and berm formation. However, together with wave forcing, tides modulate the predicted nearshore sediment dynamics. The combination of tides and wave action has a notable effect on longshore suspended sediment transport fluxes, relative to wave action alone. The model's ability to predict sediment transport under propagation of obliquely incident wave conditions underscores its potential for understanding the evolution of beach morphology at field scale. For example, the results of the model confirmed that the wave characteristics have a considerable effect on the cumulative erosion/deposition, cross-shore distribution of longshore sediment transport and transport rate across and along the beach face. In addition, for the same type of oceanic forcing, the beach morphology exhibits different erosive characteristics depending on grain size (e.g., foreshore profile evolution is erosive or accretive on fine or coarse sand beaches, respectively). Decreasing wave height increases the proportion of onshore to offshore fluxes, almost reaching a neutral net balance. The sediment movement increases with wave height, which is the dominant factor controlling the beach face shape.

• Journal of Korean Society on Water Environment
• /
• v.27 no.1
• /
• pp.19-29
• /
• 2011

In order to assess the influences of bottom sediment on water quality, following measurement were made. (1) Estimations of pollutant loads from the bottom sediment based on mass balance concept, (2) measurements of pollutant concentrations in the sediment to assess the pollution level and influence potential, (3) in situ and laboratory measurements of Sediment Oxygen Demants (SOD) and pollutant load (sediment release) from bottom sediment. Analyses of inflow and outflow loadings using simple mass balance show that there are some variations found according to the pollutants. However, there is no consistent evidence that the sediment can be a source of pollutants. Pollutant concentrations in the sediment range 16~724.8 mg/kg (COD), 1.68 ~12.64 mg/kg (T-P), 5.6~76.8 mg/kg (T-N), 0.32~21.6 mg/kg ($NH_3$-N), 0.092~0.544 mg/kg ($NO_2$-N), 4.8~18.4 mg/kg ($NO_3$-N), and 1.59~11.23 mg/kg ($PO_4$-P). Measured SOD ranges $0.190{\sim}0.802g{\cdot}m^{-2}{\cdot}d^{-1}$ and measured release rate ranges $-1618.42{\sim}10mg/m^2{\cdot}d$(COD), $-12{\sim}16mg/m^2{\cdot}d$(T-P), $-197.37{\sim}140mg/m^2{\cdot}d$(T-N), $0.4{\sim}74.32mg/m^2{\cdot}d$($NH_3$-N), $-2.04{\sim}0.8mg/m^2{\cdot}d$ ($NO_2$-N), $-70{\sim}40mg/m^2{\cdot}d$ ($NO_3$-N), and $-26.11{\sim}28.55mg/m^2{\cdot}d$($PO_4$-P). All study results indicate that bottom sediments in the Seoha weir show only limited effects on the water quality. It implies that sediment dredging is not an effective option or management measure to reduce pollutant loading.

• Water for future
• /
• v.29 no.2
• /
• pp.129-141
• /
• 1996

A procedure for computing total suspended sediment load is presented based on a single point-integrated sample, a power velocity distribution, and Laursen's sediment concentration distribution equation. The procedure was tested with field data from the Rio Grande River. Computed concentrations agreed well with depth-integrated measurements corrected for unmeasured load using nominal values of $\beta$, $\kappa$ and w. Even better agreement was obtained when site-specific data were used to define the x and z exponents of the velocity and concentration distributions. The difference between total suspended load computed using a single measurement and this procedure and conventional computations based on depthintegrated measurements is well within sampling error. There are major advantages in estimating total suspended load using a single time-integrated suspended-sediment point sample. Less field time is required; sampling costs are greatly reduced; and sampling can be more frequent and better timed to measure the changing sediment load. Single-point sampling makes automatic sampling procedures more feasible.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.325-333
• /
• 2020

Current methods of measuring the sediment concentration of natural streams can be affected by weather conditions and have lower reliability in bed-load sections due to mechanical limits. Theoretical methods have to be used to solve this problem, but they have low reliability compared to the measured values and diverse results for the bed-load sediment concentration. This study proposes a new way to reliably determine the bed-load sediment concentration from the relation with theoretical depth-integrated concentration based on the informational entropy concept. Sediment distribution shows a uniform probability distribution under maximized entropy conditions under some constraints, so a function can be calculated for the sediment distribution and depth-integrated concentration. The parameters of a stream were estimated by a nonlinear regression method using the concentration data from a past experiment. Equilibrium N (EN) was estimated using the relation between two different formulas proposed in this study, which can ease the estimation of both the total sediment distribution and depth-integrated sediment concentration with high reliable results with an average R2 of 0.924.

• Journal of Korean Society on Water Environment
• /
• v.32 no.1
• /
• pp.108-114
• /
• 2016

Sediment-laden water leads to water quality degradation in streams; therefore, best management practices must be implemented in the source area to control nonpoint source pollution. Field monitoring was implemented to measure precipitation, direct runoff, and sediment concentrations at a control plot and straw-applied plot to examine the effect on sediment reduction in this study. A hydrology model, which employs Curve Number (CN) to estimate direct runoff and the Universal Soil Loss Equation to estimate soil loss, was selected. Twenty-five storm events from October 2010 to July 2012 were observed at the control plot, and 14 storm events from April 2011 to July 2011 at the straw-applied plot. CN was calibrated for direct runoff, and the Nash-Sutcliffe efficiency and coefficient of determination were 0.66 and 0.68 at the control plot. Direct runoff at the straw-applied plot was calibrated using the percentage direct runoff reduction. The estimated reduction in sediment load by direct runoff reduction calibration alone was acceptable. Therefore, direct runoff-sediment load behaviors in a hydrology model should be considered to estimate sediment load and the reduction thereof.

• Journal of Korea Water Resources Association
• /
• v.42 no.9
• /
• pp.737-745
• /
• 2009

Field measured sediment yield from an experimental urbanized basin was compared with the predicted sediment yields with RUSLE (Revised Universal Soil Loss Equation), and MUSLE (Modified Universal Soil Loss Equation). The experimental basin is 3.1km2 in area and fifty six percent of the total area had been urbanized. The hydrological data have been measured with T/M at the outlet of the experimental basin. Runoff from the basin and rainfall depth of the basin were measured every minute. Bed load and suspended load were also measured for a given flow rate. Runoff rating curves and sediment rating curve were developed for the last three years. RUSLE showed scattered prediction results but the average of the prediction values was close to the measured one. Meanwhile, MUSLE showed linear correlation between the measured sediment yield and predicted one with high correlation coefficient. But MUSLE predicts high values than the real one. Therefore, adjustment is necessary to apply MUSLE in estimation of sediment yield from the experimental urbanized basin.