• Journal of the Korean Society of Radiology
• /
• v.3 no.3
• /
• pp.23-25
• /
• 2009

Gd-157 material has very large neutron capture cross section in the thermal region. So it is very useful to shield material for thermal neutrons. Futhermore, in the neutron capture experiment and calculation, the neutron absorption and scattering are very important. Especially these effects are conspicuous in the resonance energy region and below the thermal energy region. In the case of very narrow resonance, the effect of scattering is to be more considerable factor. In the present study, we obtained energy dependent neutron absorption ratios of natural indium in energy region from 0.003 to 100 keV by MCNP-4B Code. The coefficients for neutron absorption was calculated for circular type and 1 mm thickness. In the lower energy region, neutron absorption is larger than higher region, because of large capture cross section (1/v). Furthermore it seems very different neutron absorption in the large resonance energy region. These results are very useful to decide the thickness of sample and shielding materials.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.5
• /
• pp.401-408
• /
• 2012

Volumetric mass transfer coefficient was measured with carbon dioxide and deionized water for the gas-liquid cocurrent slug flow in 2, 5 and 8 mm tubes. Measurement was repeated with and without a vertical section in an experimental setup and entrance effect was found greater for smaller tubes. Volumetric mass transfer coefficient in the vertical section was found generally a strong function of gas- and liquid-phase superficial velocities. 5 mm- and 8 mm-tube data are highly consistent each other but not with 2 mm tube.

• Journal of Korean Dental Science
• /
• v.2 no.2
• /
• pp.31-34
• /
• 2009

The survival rate of the OSSTEM GS II Implant 1 year after serving the prosthetic function in 2 domestic and foreign medical institutes was 97.57%; the success rate was 95.7%, and the average alveolar bone resorption was 0.24mm(n=389). In particular, the alveolar bone resorption occurred differently according to the placement location as well as whether or not the patient underwent bone grafting operation, but the implant s length and diameter did not have significant impact on alveolar bone resorption.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.4
• /
• pp.225-232
• /
• 2009

An analytical compact model for the asymmetric lightly doped Double Gate (DG) MOSFET is presented. The model is developed using the Lambert Function and a 2-dimensional (2-D) parabolic electrostatic potential approximation. Compact models of the net charge and channel current of the DG-MOSFET are derived in section 2. Results for the channel potential and current are compared with 2-D numerical data for a lightly doped DG MOSFET in section 3, showing very good agreement.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.6
• /
• pp.47-52
• /
• 2003

To determine the effect of transverse open crack on the dynamic behavior of simply-supported Euler-Bernoulli beam with the moving masses, an iterative modal analysis approach is developed. The influence of depth and position of the crack in the beam, on the dynamic behavior of the simply supported beam system, have been studied by numerical method. The cracked section is represented by a local flexibility matrix, connecting two undamaged beam segments that is, the crack is modeled as a rotational spring. This flexibility matrix defines the relationship between the displacements and forces across the crack section, and is derived by applying a fundamental fracture mechanics theory. As the depth of the crack is increased, the mid-span deflection of the simply-supported beam, with the moving mass, is increased. The crack is positioned in the middle point of the pipe, and the mid-span defection of the simply-supported pipe represents maximum deflection.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.1
• /
• pp.197-205
• /
• 1992

For the optimal design of composite breakwaters, a computer program PROCOBRA is developed using the combined ALM-BFGS algorithm. A model formulation for the section design optimization problem of composite breakwaters is proposed where a concept of subsectional weighting factors is introduced in the objective function. Usability of the program is verified through a numerical example. From the study, it is found that the ALM-BFGS method is reliable and can be effectively applied for the design optimization of coastal structures. Compared with conventional design process, it is proved that the economical design of composite breakwaters is possible.

• Journal of Powder Materials
• /
• v.5 no.4
• /
• pp.299-302
• /
• 1998

Dimensional accuracy is one of the most important issues in the production of sintered parts. The iron-copper-carbon system is commonly used alloys in sintered structural parts production. The dimensional control of these alloys, however, is not easy because of their complex sintering behavior. This study is an effort to clarify the influence of common factors on dimensional change of Fe-Cu-C sintered structural parts. We determined the effect of such various parameters as chemical composition, particle diameter, compact density, sintering temperature and sintering time on dimensional changes. Consequently, we obtained a useful formula to predict the final dimension in function of these parameters. The effect of typical impurities in copper powder on the dimensional change of sintered parts has also been described.

• 연구논문집
• /
• s.34
• /
• pp.87-99
• /
• 2004

A spring tension control device is used as a very important part of an twister system. The friction force of tensioner must keep same friction force during winding in package. For satisfy this function, many device used common compression coil spring. In this paper, by using the case-building technique which was based on simple theory that unknown design variables are induced by given input design variables by the designer, design automation algorithm about rectangular section compression springs with elastic characteristic is developed. Four design equation are justified in using of analysis of torsion of straight bar of rectangular section and geometrical condition of coil spring. Four design equation and nine design variables are computed by case-building technique.

• Nuclear Engineering and Technology
• /
• v.35 no.6
• /
• pp.581-595
• /
• 2003

Transport lattice codes require the resonance integral tables for the resonant nuclides where the resonance integral is a function of the background cross section and can be prepared through a special program solving the slowing down equation. In case the cross section libraries do not include the resonance integral table for the resonant nuclides, the computational prediction produces a large error. We devised a new method using a Monte Carlo calculation for the effective resonance cross sections to solve this problem provisionally. We extended this method to obtain the resonance integral table for general purpose. The MCNP code is used for the effective resonance integrals and the LIBERTE code for the effective background cross sections. We modified the HELIOS library with the effective cross sections and the resonance integral tables obtained by the newly developed Monte Carlo method, and performed sample calculations using HELIOS and LIBERTE. The results showed that this method is very effective for the resonance treatment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.3
• /
• pp.58-65
• /
• 1996

This thesis is concerned with the study on the characteristics of the cutting resistance occurring in finish machining of hardened steels such as carbon tool steel and alloy tool steel by a ceramic tool with nose radius. For the purpose, the shape of cutting cross-section made at nose part of the tool was analyzed geometrically and the wear mechanism on the flank face of the ceramic tool is investigated. In order to investigate the characteristics of cutting resistance two categories of cutting conditions are suggested, along with geometrical analysis. One category includes the conventional cutting parameters such as feed and depth of cut, another containing new cutting parameters of thickness of cut and width of cut etc. Thickness of cut width of cut and area of undeformed chip section formed by the condition of engagement between workpiece and cutting tool are determined as the function of feed, depth of cut and nose radius of cutting too, And an effective approach angle is determined by depth of cut and nose radius.