• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1445-1447
• /
• 2008

Micro crystal structure of polycrystalline MgO film is controlled by adjusting the energy of particles arrived at the substrate during deposition. The change of crystal structure affects on the total area of (200) surface where the oxygen vacancies are formed easily, resulting in the change of secondary electron emission (SEE) coefficient($\gamma$).

• 한국대기환경학회지
• /
• 제31권5호
• /
• pp.437-448
• /
• 2015

The purpose of this study is to present the source contribution of the fine particles ($PM_{2.5}$) in Chungju area using the CMB (chemical mass balance) method throughout the four seasons in Korea. The Chungju's annual average level of $PM_{2.5}$ was $48.2{\mu}g/m^3$, which exceeded two times higher than standard air quality. Among these particles, the soluble ionic compounds represent 54.2% of fine particle mass. Additionally, the OC concentration in Chungju stayed similar to other domestic cities, while the EC concentration decreased significantly compared to other domestic/international cities. The concentration of sulfur represented the highest composition (8%) among the fine particle compounds. According to the CMB results, the general trend of the $PM_{2.5}$ mass contributors was the following: secondary aerosols (50.5%: ammonium sulfate 26.5% and ammonium nitrate 24.0%) > gasoline vehicle (18.3%) > biomass burning (11.0%) > industrial boiler (6.0%) > diesel vehicles (4.4%). The contribution of the secondary aerosols was the main cause than others. This impact is assumed to be emitted from air pollutants of urban cities or neighbor countries such as China.

• Asian Journal of Atmospheric Environment
• /
• 제3권1호
• /
• pp.42-51
• /
• 2009

Saturated n-dicarboxylic acids ($C_2-C_7$, $C_9$), unsaturated dicarboxylic acids (maleic, fumaric, phthalic acid), ketocarboxylic acids (pyruvic, glyoxylic acid), and dicarbonyls (glyoxal, methylglyoxal) were determined in size-segregated samples with a high-volume Andersen air sampler at a suburban site in Saitama, Japan, May 12-17 and July 24-27, 2007 and January 22-31, 2008. The seasonal average concentrations of these detected organic acids were 670 $ng/m^3$, accounting for about 4.4-5.7% (C/C) of water-soluble organic carbon (WSOC) and 2.3-3.6% (C/C) of organic carbon (OC). The most abundant species of dicarboxylic acids was oxalic acid, followed by malonic, phthalic, or succinic acids. Glyoxylic acid and methyglyoxal were most abundant ketocarboxylic acid and dicarbonyl, respectively. Seasonal differences, size-segregated concentrations, and the correlations of these acids with ambient temperatures, oxidants, elemental carbon (EC), OC, WSOC, and ionic components were also discussed in terms of their corresponding sources and possible secondary formation pathways. The results suggested that photochemical reactions contributed more to the formation of particulate organic acids in Saitama suburban areas than did direct emissions from anthropogenic and natural sources. However, direct emissions of vehicles were also important sources of several organic acids in particles, such as phthalic and adipic acids, especially in winter.

• 한국세라믹학회지
• /
• 제53권2호
• /
• pp.134-138
• /
• 2016

Porous $Co_3O_4$ spheres with bimodal pore distribution (size: 2-3 nm and ~ 30 nm) were prepared by ultrasonic spray pyrolysis of aqueous droplets containing Co-acetate and polyethylene glycol (PEG), while dense $Co_3O_4$ secondary particles with monomodal pore distribution (size: 2-3 nm) were prepared from the spray solution without PEG. The formation of mesopores (~ 30 nm) was attributed to the decomposition of PEG. The responses of a porous $Co_3O_4$ sensor to various indoor air pollutants such as 5 ppm $C_2H_5OH$, xylene, toluene, benzene, and HCHO at $200^{\circ}C$ were found to be significantly higher than those of a commercial sensor using $Co_3O_4$ and dense $Co_3O_4$ secondary particles. Enhanced gas response of porous $Co_3O_4$ sensor was attributed to high surface area and the effective diffusion of analyte gas through mesopores (~ 30 nm). Highly sensitive porous $Co_3O_4$ sensor can be used to monitor various indoor air pollutants.

• 한국건설순환자원학회논문집
• /
• 제10권3호
• /
• pp.293-299
• /
• 2022

본 연구에서는 도로변 미세먼지 내 타이어와 도로 마모입자의 정량화 분석과 타이어와 도로 마모입자 내 타이어 및 도로 성분 비율을 확인하기 위한 연구를 수행하였다. 이에 시간당 1,300여대 교통량을 갖는 충청남도 지자체중에서 C도시의 종합버스터미널 부근 정류장의 경계석 6곳에서 먼지 샘플을 채집하였다. 채집된 먼지 샘플 1,000 g에 대해 크기와 밀도 분리 수행한 결과 미세먼지 샘플 24 g과 타이어와 도로 마모입자 약 0.05 g이 분리되었다. 즉, 도로변 미세먼지에는 타이어와 도로 마모입자가 약 0.21 % 존재하는 것으로 분석되었다. 분리된 타이어와 도로 마모입자에 대해 주사전자현미경(SEM)을 이용하여 형상을 분석한 결과 지우개가루 형상이 관찰되었다. 또한, 도로변 미세먼지 내 존재하는 타이어와 도로 마모입자는 자동차 주행 중 타이어와 도로간 마찰에 의해 생성되어 도로변으로 분산되었기 때문에 열중량분석기(TGA)와 가스크로마토 질량분석기(GC/MS)를 이용하여 성분 분석을 수행하였다. 정량화 계산식을 통해 성분에 대한 타이어 및 도로 성분 비율을 도출한 결과 약 3:7로 분석되었다. 본 연구는 도로변 미세먼지 발생원의 구성원과 함량 분석을 위해 객관적이고 신뢰도 높은 분석 기법을 제시하였다. 추후, 도로건설과 타이어 소재의 미세먼지 저감 기술 확보와 개선 방안 확보를 위한 선행적 기초 연구로써 활용되기를 기대하고 지속적으로 더 많은 지역과 샘플 분석에 대한 통계 데이터를 확보하여 신뢰도 높은 연구를 수행하고자 한다.

• 한국재료학회지
• /
• 제28권6호
• /
• pp.337-342
• /
• 2018

Using a high pressure homonizer, we report on the electrochemical performance of $Li_4Ti_5O_{12}(LTO)$ particles manufactured as anode active material for lithium ion battery. High-pressure synthesis processing is performed under conditions in which the mole fraction of Li/Ti is 0.9, the synthesis pressure is 2,000 bar and the numbers of passings-through are 5, 7 and 10. The observed X-ray diffraction patterns show that pure LTO is manufactured when the number of passings-through is 10. It is found from scanning electron microscopy analysis that the average size of synthesized particles decreases as the number of passings-through increases. $LiCoO_2-based$ active cathode materials are used to fabricate several coin half/full cells and their battery characteristics such as lifetime, rate capability and charge transfer resistance are then estimated, revealing quite good electrochemical performance of the LTO particles as an effective anode active material for lithium secondary batteries.

• 한국입자에어로졸학회지
• /
• 제4권2호
• /
• pp.51-67
• /
• 2008

In this study, we devoted to kinetic measurement of the catalytic oxidation of iron-containing flame soot particles and better understanding the role of catalytic particles on carbon oxidation in particular at low temperature, targeting on autothermal regeneration of diesel particulate filter by diesel exhaust gas. Carbon-based Fe-containing particles generated by spraying ferrocene-doped diesel fuel in an oxy-hydrogen flame are tested and compared with a commercial carbon black powder for thermogravimetric analysis (TGA), secondary ion mass spectrometry (SIMS), Fourier-transform infrared spectroscopy (FTIR), Induced coupled plasma-Atomic emission spectroscopy (ICP-AES), and High-resolution transmission electron microscopy (HR-TEM). As a result, we found that a small amount of the ferrocene addition led to significant reductions in a on-set temperature and an activation energy of the carbon oxidation as well. An oxygenated surface complex forming at the particle surface could be thought as active species that would be readily consumed in particular at low temperature.

• 한국주조공학회지
• /
• 제24권2호
• /
• pp.108-114
• /
• 2004

$Al_2O_3$, SiC reinforced Al matrix composites were fabricated by centrifugal spray casting method and their wear resistance characteristics have been studied. Particles are generally uniformly distributed in the microstructure of as-cast specimens. In order to investigate the effect of secondary deformation, hot rolling was performed for each specimen of pure Al matrix composites with a reduction of 10, 20, 30, 40 and 50% at $400{\sim}500^{\circ}C$, respectively. Microstructure of specimen showed that particle distribution density and hardness increased because of increasing of reduction ratio. Wear test with a various sliding velocity of 1.98, 2.38, 2.88 and 3.53m/sec showed that the wear resistance characterization of composite improved remarkably compared to the normal alloy and performs without reinforced particles. Microstructural observation for the worn surface of pure Al specimens without particles showed that a change in wear mechanism seemed to separate layer by surface fatigue. In other case of Al composite reinforced with $Al_2O_3$ and SiC, the grinder type of wear mechanism was shown.

• 한국물환경학회지
• /
• 제25권6호
• /
• pp.935-942
• /
• 2009

During period of the rainy season of spring tide Aug. 2005, the suspended sediment transport rate from Seomjin River increased ten times as high as neap tide of low river discharge. During ebb tide of high terrestrial input, the grain size of suspended particles of both surface and bottom layer of the water column, showed a uni-modal distribution with a dominant peak at coarse fraction, which suggests a characteristic development of floc-sized particles of low mean effective density. On the contrary, the particles supplied toward upstream of Seomjin river from Gwangyang Bay during flood tide showed a bi-modal distribution with a secondary peak at finer fraction, possibly due to the resuspension and the deflocculation associated with the increased shear velocity at near bottom. Break-up of large flocs is also suggested by the increased mean effective density. However, settling velocity was lower during flood tide because of smaller grain size. Thus, net deposition of suspended sediment is expected at within Gwangyang Bay instead of upstream of Seomjin River, even though suspended sediment transport rate at near bottom water was three times higher than that at surface water during flood tide.

• Journal of Magnetics
• /
• 제14권2호
• /
• pp.71-74
• /
• 2009

The magnetic and structural properties of FINEMET (the Hitachi product name of the Fe-Si-B-Nb-Cu alloy) nanopowder with a composition of $Fe_{73.5}Si_{13.5}B_9Nb_3Cu_1$ atomic percent were investigated after annealing, chemical etching, and mechanical milling. The primary and secondary crystallization temperatures were 523 and $550^{\circ}C$, respectively. The grain size of the particles was adjusted by annealing time. Optimally annealed particles exhibited a homogenous microstructure composed of nanometer-sized crystalline grains. The grain boundary of the annealed particles was etched preferentially by chemical etching. Chemically etched particles were broken at the grain boundary by high-energy ball milling. As a result, a nanometer-sized FINEMET powder with a uniform size of crystalline grains was fabricated.