• 한국소음진동공학회논문집
• /
• 제12권9호
• /
• pp.717-724
• /
• 2002

In this study, a numerical analysis for the piston secondary dynamics of small refrigeration reciprocating compressors is performed. In general, the length of cylinder in this class of compressors is shortened to diminish the frictional losses of the piston-cylinder system. So, the contacting length between piston and cylinder wall is in variable with the rotating crank angle around the BDC of the reciprocating piston. In the problem formulation of the piston dynamics, the change in bearing length of the piston and all corresponding forces and moments are considered in order to determine the piston trajectory, velocity and acceleration at each step. A Newton-Raphson procedure was employed in solving the secondary dynamic equations of the piston. The developed computer program can be used to calculate the entire piston trajectory and the hydrodynamic force and moment as functions of crank angle under compressor running conditions. The results explored the effects of the radial clearance, lubricant viscosity, length of the cylinder wall, and pin location on the stability of the piston.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.67-72
• /
• 2002

Today, the research to examine a fact that interaction between the air and the fluid free surface affects the steady state flow and air. We proved the interaction between vortex pairs and free surface on each condition that is created by the end of delta wings. another purpose of this study is to investigate the effect of surface active material which can change the surface tension and we must consider when we refer to turbulent flow on surface tension. therefore, this research examined the growth process of vortex pairs on condition of clean, contaminated free surface and wall after we made vortex pairs through counter rotating flaps. The results of this study suggest that vortex pairs in clean free surface rise safely but the vortex pairs in contaminated free surface and rigid, no slip is made secondary vortex or rebounding. However the secondary vortex in rigid, no slip is stronger than before, and we can find the vortex shape which roll up more completely. However, these will disappear by the effect of wall.

• Journal of the Korean Wood Science and Technology
• /
• 제9권1호
• /
• pp.1-12
• /
• 1981

The structure of spiral thickenings, particulary the appearance, arrangement and orientation of thickenings in compression wood of Torreya nucifera, were studied in detail by light and polarizing microscope, scanning and transmission electron microscope. The results obtained are as follows: (1) Using the inclined sections at an angle of 45 degrees to the fiber axis, it seems that we can not only observe the more accurate transverse view of the thickenings but also investigate the formation of their thickenings. (2) Generally 2-4 pieces of thickenings are projected to the cell lumen as nipple-like appearance in transverse section and are as frequent, well developed, forming pair and have the rope-like appearance in radial surface. (3) The secondary wall of early wood is composed of 3 layers (S1, S2, S3) and orientation of thickening appears S helix but that of late wood is of 2 layers (S1, S2) and that orientation shows Z helix. Above two regions are demaracted at several tracheid cells from the growth ring boundary. (4) Orientation of thickening seems to be a element showing the characteristics of compression wood in Torreya nucifera. (5) It believes that the thickenings of compression wood are integral part of the S3 in early wood tracheids and of the S2 in late wood and have the same orientations as the inner-most microfibrils in these layers. (6) Thickening and cavities seem to be not formed together in a secondary cell wall of same tracheids.

• 대한기계학회논문집B
• /
• 제23권1호
• /
• pp.92-103
• /
• 1999

The fuel spray behavior in the intake port of an electronic control port irijection gasoline engine has a strong influence on engine performance, exhaust emission and fuel consumption. Thus, in this study, fuel spray behavior and flow characteristics of the air assist gasoline spray injected into a suction flow in a simulated rectangular intake port have boon investigated. Macro-behavior of spray characteristics was investigated by means of visualization and the measurements of SMD and velocity were made by PDPA. For analysis the flow field with droplets size, droplets are classified five droplets size groups. As a result, the normal distance of suction flow increasing, the relatively large droplets distribution and SMD increase because small droplets easily follow suction flow. Near impinging wail, after impinging against the wall, secondary atomized small droplets of D < $30{\mu}m$ bound from the wall. And the increasement of suction flow progress to the large droplets of D > $100{\mu}m$ distribution. Therefore, SMD are apparently increased near impinging wall, Z/d = 9.0.

• 대한기계학회논문집A
• /
• 제29권8호
• /
• pp.1102-1108
• /
• 2005

The integrity of nuclear piping systems has to be maintained sufficiently all the times during operation. In order to maintain the integrity, reliable assessment procedures including fracture mechanics analysis, etc, are required. Up to now, the integrity assessment has been performed using conventional deterministic approach even though there are lots of uncertainties to hinder a rational evaluation. In this respect, probabilistic approach is considered as an appropriate method for piping system evaluation. The objectives of this paper are to develop a probabilistic assessment program using reliability index and simulation technique and to estimate the damage probability of wall-thinned pipes in secondary systems. The probabilistic assessment program consists of three evaluation modules which are first order reliability method, second order reliability method and Monte Carlo simulation method. The developed program has been applied to evaluate damage probabilities of wall-thinned pipes subjected to internal pressure, global bending moment and combined loading. The sensitivity analysis results as well as prototypal evaluation results showed a promising applicability of the probabilistic integrity assessment program.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.751-757
• /
• 2001

An experimental study of impinging jet-flow structure has been carried out for a fully developed single circular jet impingement cooling on a flat plate, and the effect of the wall thickness at nozzle exit edge is investigated. Impinging jet flow structures have been measured by Laser-Doppler Velocimeter to interpret the heat transfer results presented previously by Yoon et al.(sup)(10) The peaks of heat transfer rate are observed near the nozzle edge owing to the radial acceleration of jet flow when the nozzle locates close to the impingement plate. The growth of the velocity fluctuations in the wall jet flow is induced by the vortices which originate in the jet shear layer, and consequently the radial distribution of local Nusselt numbers has a secondary peak at the certain radial position. As a wall of circular pipe nozzle becomes thicker for small nozzle-to-target distance, the entrainment can be inhibited, consequently, the acceleration of wall jet flow is reduced and the heat transfer rate decreases.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2001년도 춘계학술발표회요약집
• /
• pp.127.2-127
• /
• 2001

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2002년도 추계학술발표회요약집
• /
• pp.401.1-401
• /
• 2002

• Journal of Chest Surgery
• /
• 제8권2호
• /
• pp.159-168
• /
• 1975

We have experienced 61 cases of Clinically diagnosed tuberculous peripleural abscess which was surgically treated at St. Mary's Hospital of Catholic Medical College from Mar. 1963 to Feb. 1974. Out of them, 52 cases of pathologically confirmed tuberculous peripleural abscess were reviewed and its pathogenesis, treatment and so called "rib caries" were discussed. In the past, they have been described as a variety of the names, such as rib caries, cold abscess of the chest wall, pericostal abscess, lymphadenitis tuberculosa of the chest wall, chronic draining sinuses of the chest wall and other descriptive terms. Although it has been said that the tuberculous abscess on the chest wall developed as a secondary disease from so called "rib caries" but now it has been clear that this abscess occurred not from tuberculosis of the rib but from tuberculous lesion developed between end-othoracic fascia and parietal pleura usually following pulmonary tuberculosis and/or tuberculous pleurisy and the involvement of rib or ribs are secondary one from peripleural abscess, as we confirmed. Therefore we advocate that the nomination, rib caries, should not be used unless there is a primary tuberculous lesion on ribs. The results were as follows: 1. The highest age group of tuberculous peripleural abscess was ranged from the first to third decade (78%) 2. The location of tuberculous peripleural abscess on the chest wall were as follows, 31 cases on the anterior, 19 cases on lateral and 2 cases on the posterior. 3. On x-ray examination, abnormal findings including parenchymal tuberculous lesion and pleural changes were seen is 38 cases. 4. There was no destructive change of periosteum and rib in 23 cases of tuberculous peripleural abseess during operation. However the periosteal denudation and/or rib destruction were found in 29 cases. 5. The all cases of tuberculous peri pleural abscess developed from between endothoraclc fascia and parietal pleura, as we confirmed. With antituberculous therapy, operation should be radical by wide incision on the lesion including thorough curettage with proper drainage of Iiquified caseating materials and appropriate rib resection, if necessary.tion, if necessary.

• Corrosion Science and Technology
• /
• 제14권1호
• /
• pp.1-11
• /
• 2015

Local wall thinning and integrity degradation caused by several mechanisms, such as flow accelerated corrosion (FAC), cavitation, flashing and/or liquid drop impingements, are a main concern in carbon steel piping systems of nuclear power plant in terms of safety and operability. Thinned pipe management program (TPMP) had been developed and optimized to reduce the possibility of unplanned shutdown and/or power reduction due to pipe failure caused by wall thinning in the secondary side piping system. This program also consists of several technical elements such as prediction of wear rate for each component, prioritization of components for inspection, thickness measurement, calculation of actual wear and wear rate for each component. Decision making is associated with replacement or continuous service for thinned pipe components. Establishment of long-term strategy based on diagnosis of plant condition regarding overall wall thinning is also essential part of the program. Prediction models of wall thinning caused by FAC had been established for 24 operating nuclear plants. Long term strategies to manage the thinned pipe component were prepared and applied to each unit, which was reflecting plant specific design, operation, and inspection history, so that the structural integrity of piping system can be maintained. An alternative integrity assessment criterion and a computer program for thinned piping items were developed for the first time in the world, which was directly applicable to the secondary piping system of nuclear power plant. The thinned pipe management program is applied to all domestic nuclear power plants as a standard procedure form so that it contributes to preventing an accident caused by FAC.