• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.1
• /
• pp.165-173
• /
• 1997

The present study investigates heat/mass transfer for flow through perforated plates for application to combustor wall and turbine blade film cooling. The experiments are conducted for hole length to diameter ratios of 0.68 to 1.5, for hole pitch-to-diameter ratios of 1.5 and 3.0, for gap distance between two parallel perforated plates of 1 to 3 hole diameters, and for Reynolds numbers of 60 to 13, 700. Local heat/mass transfer coefficients near and inside the cooling holes are obtained using a naphthalene sublimation technique. Detailed knowledge of the local transfer coefficients is essential to analyze thermal stress in turbine components. The results indicate that the heat/mass transfer coefficients inside the hole surface vary significantly due to flow separation and reattachment. The transfer coefficient near the reattachment point is about four and half times that for a fully developed circular tube flow. The heat/mass transfer coefficient on the leeward surface has the same order as that on the windward surface because of a strong recirculation flow between neighboring jets from the array of holes. For flow through two perforated plate layers, the transfer coefficients on the target surface (windward surface of the second wall) affected by the gap spacing are approximately three to four times higher than that with a single layer.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.127-130
• /
• 2004

For the quality control of the industrial products, an automatic hole measuring system has been developed. The measurement device allows X-Y movement due to contact forces between a hole and its own circular cone and the device is attached to an industrial robot. Its measurement accuracy is about 0.04mm. This movement of the plate is measured by two LVDT sensor system. But this system using the LVDT sensors is restricted by high cost and precision of measurement and correspondence of environment so particularly, a vision system with CCD-Camera is discussed in this paper for the above mentioned purpose. The device consists of two of two links jointed with hinge pins basically and, they guarantee free movement of the touch prove attached on the second link in the same plane. These links are returned to home position by the spring plungers automatically after each process for the next one. On the surface of the touch prove, it has a circular white mark for camera recognition. The system detect and notify the center coordinate of capture mark image through the image processing. Its measuring accuracy has been proved to be about $\pm$0.01mm through the repeated implementation over 200 times. This technique will shows the advantage of touch-indirect image capture idea using cone-shaped touch prove in various symmetrical shaped holes particulary, like tapped holes, chamfered holes, etc As a result, we attained our object in a view of the accuracy, economical efficiency, and functionality

• The Korean Journal of Nuclear Medicine
• /
• v.19 no.1
• /
• pp.73-75
• /
• 1985

Acute transient synovitis of the hip presents clinically pain and limping. But in the majority of the cases, definite positive findings are not manifest in roentgenogram in its early phase. However radionuclide bone imaging combines with the assessment of vascularization and bone tracer uptake is of great value in solving this diagnostic problem. The materials for this study consisted of 29 children with acute transient synovitis of the hip, characterized by symptoms and physical signs of an arthritis, negative X-ray findings and disappearance of all symptoms and signs within a short period of time. They were twenty males and 9 females and age ranged from 1 to 12 years. We took pelvic reontgenogram in AP and frog-leg views. After intravenous bolus injection of 10 to 15 mCi of $^{99m}Tc-methylene$ diphosphonate, 24 sequential image of the pelvis was taken at 2-second interval for blood flow study. The scintigrams were made using a gamma camera with high resolution parallel hole collimator. Blood pool imaging was obtained at 2 minutes after tracer administration. After 3 hours, static images were taken and then closeup image of the hip using pin-hole collimator was followed. The results were as follows: 1) Bone scintigram was much more sensitive than conventional roentgenogram in diagnosis of acute transient synovitis of the hip. 2) Three-phase imagings showed increased vascular activities in blood pool scintigrams in 96%. 3) Pin-hole imaging showed increased tracer uptake in the regional bones of the hip, par ticularly in the medial aspect of femoral head and acetabulum. 4) We confirmed that three-phase imaging reinforced with pin-hole technique were very useful in diagnose of acute transient synovitis of the hip.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.105-111
• /
• 2003

Wheel for passenger car support the car weight with tires, and they transmit rolling and braking power into the ground. Whittling away at wheel weight is more effective to boost fuel economy than lighting vehicle body structure. A shape of hole in disk is optimized for minimizing the weight of steel wheel. Pro/ENGINEER program is used for formulating the design model, and ANSYS package is selected for analyzing the design model. It has difficulties to interface these commercial software directly. For Combining both programs, response surface methodology is applied to construct approximation functions for maximum stresses and maximum displacements are obtained by full factorial design of five levels. This steel wheel is modeled in 14-inch diameter of rim, and wide parameter of hole in disk is only selected as design variable for reducing the weight of steel whee. PLBA(Pshenichny-Lim-Belegundu-Arora) algorithm, which used the second-order information in the direction finding problem and uses the active set strategy, is used for solving optimization problems.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.244.1-244.1
• /
• 2013

The p-type GaN which act as a hole injection layer in GaN-based LEDs has fundamental problems. The first one arises from the difficulty in growing a highly doped p-GaN (with a carrier concentration exceeding ~1018 $cm^{-3}$). And the second one is the absence of appropriate metals or conducting oxides having a work function that is larger than that of p-type GaN (7.5 eV). Moreover, the LED efficiency is decreases gradually as the injection current increases (the so-called 'efficiency droop' phenomenon). The efficiency droop phenomenon in InGaN quantum wells (QWs) has been a large obstacle that has hindered high-efficiency operation at high current density. In this study, we introduce the new approaches to improve the light-output power of LEDs by using graphene oxide sheets. Graphene oxide has many functional groups such as the oxygen epoxide, the hydroxyl, and the carboxyl groups. Due to nature of such functional groups, graphene oxide possess a lot of hole carriers. If graphene oxide combine with LED top surface, graphene oxide may supply hole carriers to p-type GaN layer which has relatively low free carrier concentration less than electron concentration in n-type GaN layer. To prove the enhancement factor of graphene oxide coated LEDs, we have investigated electrical and optical properties by using ultra-violet photo-excited spectroscopy, confocal scanning electroluminescence microscopy.

• Computers and Concrete
• /
• v.32 no.1
• /
• pp.99-117
• /
• 2023

The crack under the influence of the higher intensities of the stresses grows and the structure gets collapsed with the time when the crack length reaches to critical value. Therefore, the fracture behavior of a structure in terms of stress intensity factors (SIF) becomes important to determine the remaining fracture strength and capacity of material and structure for avoiding catastrophic failure, increasing safety and further improvement in the design. The robustness of the method has been demonstrated by comparing the numerical results with analytical and experimental results of some problems. XFEM is used to model cracks and holes in structures and predict their strength and reliability under service conditions. Further, XFEM is extended with a stochastic method for predicting the sensitivity in terms of output COVs and fracture strength in terms of mean values of stress intensity factors (SIFs) of a structure with discontinuities (cracks and holes) under tensile loading condition with input individual and combined randomness in different system parameters. In stochastic technique, the second order perturbation technique (SOPT) has been used for the predicting the fracture behavior of the structures. The stochastic/perturbation technique is also known as Taylor series expansion method and it provides the reliable results if the input randomness is less than twenty percentage. From the present numerical analysis it is observed that, the crack tip near to the hole is under the influence of the stress concentration and the variational effect of the input random parameters on the crack tip in terms of the SIFs are lesser so the COVs are the less sensitive. The COVs of mixed mode SIFs are the most sensitive for the crack angles (α=45° to 90°) for all the values of c₁ and d₁. The plate with the shorter distance between hole and crack is the most sensitive with all the crack angles but the crack tip which is much nearer to the hole has the highest sensitivity.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.200-207
• /
• 2001

Burrs farmed in drilling are classified into three types, no burr, burrs with cap, teared burr. To control burr size in drilling, the second type burrs with cap are to be formed because it is small and uniform. It is necessary to understand the mechanism of cap formation to derive the burr formation into second type burr with cap. In several materials. second type burrs are formed in drilling by changing cutting conditions. It is observed that cap is formed as a result of the plastic deformation along the outside of exit hope. According to the tension behavior of the material in concentrated region between hole and drill outside edge, the geometry of burr with cap is determined. Simplified 2D FEM analysis shows good prediction for burr formation.

• The Journal of the Acoustical Society of Korea
• /
• v.1 no.1
• /
• pp.92-96
• /
• 1982

In this paper, the interaction of electron and phonon in metals is expressed using Hamiltonian operator as follows. By excahnging phonon energy with in the vicinity of isotropical Fermi surface and using following electron and hole operators. We obtain the interaction of electron and phonon. And new Feynman Graphs are tried with the following conditions on. First, when state transfer state, phonon cannot be created. Second, when state transfer state, phonon cannot be destroyed. Third, when state transfer state, phonon can be created or destroyed. Fourth, when state transfer state, phonon can be created or destroyed.

• Asia pacific journal of information systems
• /
• v.20 no.4
• /
• pp.101-123
• /
• 2010

Recently, firms are operating a number of teams to accomplish organizational performance. Especially, ad hoc teams like proposal preparation team are quite different from permanent teams like R&D team in the sense of how the team forms network structure and deals with organizational learning culture and knowledge management participation efforts. Moreover, depending on the team characteristics, individual creativity will differ from each other, which will lead to organizational performance eventually. Previous studies in the field of creativity are lacking in this issue. So main objectives of this study are organized as follows. First, the issue of how to improve individual creativity and organizational performance will be analyzed empirically. This issue will be performed depending on team characteristics such as ad hoc team and permanent team. Antecedents adopted for this research objective are cultural and knowledge factors such as organizational learning culture, and knowledge management participation. Second, the network structure such as degree centrality, and structural hole is used to analyze its influence on individual creativity and organizational performance. SI (System Integration) companies are facing severely tough requirements from clients to submit very creative proposals. Also, R&D teams are widely accepted as relatively creative teams because their responsibilities are focused on suggesting innovative techniques to make their companies remain competitive in the market. SI teams are usually ad hoc, while R&D teams are permanent on an average. By taking advantage of these characteristics of the two kinds of teams, we will prove the validity of the proposed research questions. To obtain the survey data, we accessed 7 SI teams (74 members), and 6 R&D teams (63 members), collecting 137 valid questionnaires. PLS technique was applied to analyze the survey data. Results are as follows. First, in case of SI teams, organizational learning culture affects individual creativity significantly. Meanwhile, knowledge management participation has a significant influence on Individual creativity for the permanent teams. Second, degree centrality Influences individual creativity significantly in case of SI teams. This is comparable with the fact that structural hole has a significant impact on individual creativity for the R&D teams. Practical implications can be summarized as follows: First, network structure of ad hoc team should be designed differently from one of permanent team. Ad hoc team is supposed to show a high creativity in a rather short period, implying that network density among team members should be improved, and those members with high degree centrality should be encouraged to show their Individual creativity and take a leading role by allowing them to get heavily engaged in knowledge sharing and diffusion. In contrast, permanent team should be designed to take advantage of structural hole instead of focusing on network density. Since structural hole can be utilized very effectively in the permanent team, strong arbitrators' merits in the permanent team will increase and therefore helps increase both network efficiency and effectiveness too. In this way, individual creativity in the permanent team is likely to lead to organizational creativity in a seamless way. Second, way of Increasing individual creativity should be sought from the perspective of organizational culture and knowledge management. Organization is supposed to provide a cultural atmosphere in which Innovative idea suggestions and active discussion among team members are encouraged. In this way, trust builds up among team members, facilitating the formation of organizational learning culture. Third, in the ad hoc team, organizational looming culture should be built such a way that individual creativity can grow up fast in a rather short period. Since time is tight, reasonable compensation policy, leader's Initiatives, and learning culture formation should be done In a short period so that mutual trust is built among members quickly, and necessary knowledge and information can be learnt rapidly. Fourth, in the permanent team, it should be kept in mind that the degree of participation in knowledge management determines level of Individual creativity. Therefore, the team ought to facilitate knowledge circulation process such as knowledge creation, storage, sharing, utilization, and learning among team members, which will lead to team performance. In this way, firms must control knowledge networks in permanent team and ad hoc team in a way mentioned above so that individual creativity as well as team performance can be maximized.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05b
• /
• pp.26-27
• /
• 1992

The effect of activation and electroless nickel plating conditions on contact properties were investigated for selective electroless nickel plating of Si farers in order to obtain an optimum condition of contact hole filling. According to RCA prosess, p-type si 1 icon (100) surface was cleaned out and activated. The effects of temperture, DMAB concentration, time, and stirring iwere investigated for activation of p-type Si(100) surface. The optimal activation condition obtained was 0.5M HF, 1mM PdCl$_2$, 2mM EDTA, 7$0^{\circ}C$, 90sec under ultrasonic vibration. In electroless nickel plating, the effect of temperature, DMAB concentration, pH, and plating ti me were studied. The optimal plating condition found was 0. 10M NiS0$_4$.$H_2O$, 0.lIM Citrate, pH 6.8, 6$0^{\circ}C$, 30 minutes. The contact resistence of fi]ms wascomparatively low. It took 30 minutes to obtain 1$\mu$m thick film with 8$\mu$M DMAB concentration. The film surface roughness was improved with increasing temperature and decreasing pH of the plating solution. The best quality of the film was obtained with the condition of temperature 6$0^{\circ}C$ and pH 6.8. The micro-victors hardness of film was about 600Hv and was decreased wi th increasing particle size of plating layer.