• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.122-129
• /
• 2012

This study investigates structural and vibration analyses according to the thickness of bicycle frame tube. The model of bicycle frame has the dimension as length of 862mm, width of 100mm and hight of 402.5mm. There are 3 kinds of models with tubes of top, down and seat at bicycle frame as thicknesses of 10, 15 and 20mm. The maximum displacement and stress occur at the center part of seat stay and at the installation part of rear wheel respectively. Maximum displacements become 0.031936, 0.029159 and 0.027984mm in cases of thicknesses of 10, 15 and 20mm respectively. In case of thickness of 20mm among 3 cases, maximum displacement becomes lowest. But maximum stresses become 10.019, 8.5492 and 9.2511MPa in cases of thicknesses of 10, 15 and 20mm respectively. In case of thickness of 15mm among 3 cases, maximum stress becomes lowest. There is no resonance at practical driving conditions and natural frequency remains almost unchanged along the change of thickness. In case of the displacement due to vibration mode, the displacement difference at thickness between 15mm and 20mm becomes 1/2 times than that between 10mm and 15mm. Design at bicycle frame tube becomes most economical and durable effectively in case of thickness of 15mm among 3 cases.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.132-137
• /
• 2005

This paper addresses what amount of whole-body vibration is exposed to pilots of UH60 helicopters during flight. To measure the whole-body exposed from the feet and seat, the 12-axis vibration measurement system was used. It enables simultaneous measurement of vibration exposure from the body contact area of the feet, hip and back. The measured 12-axis vibration signals are exploited to the comfort level of UH60 helicopters during flight. It is shown that the evaluated ride value is close to $0.74{\sim}0.79m/s^2$ and that it is equivalent to the semantic scale of 'fairly uncomfortable'. To assess the health effects of whole-body vibration exposed to pilots of UH60 helicopters during their flight, the rms-based and VDV(vibration dose value)-based evaluation results of measured four-axis vibration signals are shown in this work. The fatigue-decreased proficiency limit, whose level is half of the exposure limit, is expected to come after the two-hour flight. The exposure limit is shown to reach after the 10-hour flight.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.6 s.111
• /
• pp.658-664
• /
• 2006

Shock vibrations are usually experienced in vehicles excited by impulsive input, such as bumps. The frequency weighting functions of the current standards in ISO 2631 and BS 6841 are to help objectively predict the amount of discomfort of stationary vibration. This experimental study was designed to develop frequency weighting shape for shock vibration having various fundamental frequencies from 0.5 to 16Hz. The specks were produced from the response of single. degree-of-freedom model to a half-sine force input. Fifteen subjects used the magnitude estimation method to judge the discomfort of vertical shock vibration generated on the rigid seat mounted on the simulator. The magnitudes of the shocks, expressed in terms of both peak-to-peak value and un-weighted vibration dose values (VDVs) , were correlated with magnitude estimates of the discomfort. The frequency weighting shapes from the correlation were developed and investigated having nonlinearity due to the magnitude of the shock.

• Journal of Game and Entertainment
• /
• v.1 no.1
• /
• pp.15-22
• /
• 2005

Among recent technologies that are applied to game development, virtual reality part is getting much attention for its technological effectiveness in transmitting game processing circumstances in variety that are happening in game world very realistically. In this study we analyze interface for game that is based on a action realization technology and force-feedback technology among technologies for developing virtual reality, in other words, technical analogy on game controller and the positive and negative sides of game controller for each platform. Based on that, more ordinary and effective way to deliver the functions to users in PC game field where application of force-feedback technology is least satisfied. And, Force-Feedback seat has been developed to satisfy the users' needs by using vibration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1621-1626
• /
• 2000

A simplified modeling approach for occupied car seats was demonstrated to be feasible. The model, consisting of interconnected masses, springs and dampers, was initially broken down into subsystems and experiments conducted to determine approximate values for model parameters. A short study of the effect of changing model parameters on natural frequencies, mode shapes and resonance locations in frequency response functions was given, highlighting the influence of particular model parameters on features in the mannequin's vibration response. Good agreement between experimental and simulation frequency response estimates was obtained. Future work should include optimization of parameter estimates, the inclusion of viscoelastic and nonlinear elements in addition to the linear springs and dampers, and finally extensions to a 3D model.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.9
• /
• pp.109-121
• /
• 2000

A simplified modeling approach of free vibration for occupied car seats was demonstrated to be feasible. The model consisting of interconnected masses springs and dampers was initially broken down into subsystems and experiments conducted to determine approximate values for model parameters. Which were each stiffness and damping value. Nonlinear equations of motion were derived and model parameters obtained in experiments were applied to these equations. A mathematical model of free vibration for car seat and mannequin system was built with 7 degrees of freedom. in order to calculate natural frequencies and the corresponding mode shapes. linear equations of motion were obtained through linearization. In order to explore the effects of each model parameter free vibration analysis were preformed.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.398-403
• /
• 2001

A simplified modeling approach of forced vibration for occupied car seats was demonstrated by using a mathematical model presented in previous paper. Nonlinear and linear equations of motions were rederived for forced vibration, and the transfer function was used to calculate the frequency response function. The experimental apparatus were set up and hydraulic shaker was used to obtain the system responses. Through the tests, mannequin's head had a lot of problems, and the responses with a head and without a head were measured. To explore the effects of linear dampings and friction moments at the joints, linear analyses were performed. New sets of linear spring and damping coefficients, and torsional dampings at the joints were calculated through parameter study to match up with experimental results. Good agreement between experimental and simulation frequency response estimates were obtained both in terms of locations of resonances and system deflection shapes at resonance, indicating that this is a feasible method of modeling seated occupants.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.3
• /
• pp.57-64
• /
• 2011

Vibrations on the floor in a car are transmitted to the foot, hip, and back from the seat. Human body recognizes these vibrations, but the sensitivity for each vibration is different. To evaluate these vibrations, RMS(root mean square) of accelerations, VDV(vibration does value) are commonly used. The ride comfort evaluation is usually carried out by experiments of real cars which are expensive. The purpose of this paper is to briefly review the status of several ride vibration standards and criteria having relevance to construction machinery vehicles and to suggest recommendations for the effective use of such criteria in vehicle / component development.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.413-418
• /
• 2005

Vibration test using the MAST(Multi Axial Simulation Table) is more reliable test than conventional testing process focused on one directional vibration test. The former test could be possible with a advanced control algorithm and hardware supports so that most of the operation is automatically conducted by MAST system itself except the input information that is derived from the measured data. That means the reliability of the vibration test is highly depended on the input profile than any other cases before. In this paper, the optimal algorithm based on energy method is introduced so that the best combination of candidated input PSD data could be constructed. The optimal algorithm renders time information so that the vibration fatigue test is completely possible for any measured signals one wants. The real road test is conducted in short intervals containing some rough roads and the candidated input PSD is obtained from the extra road in proving ground. The testing is targeted for the electronically operated door and seat.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.3
• /
• pp.368-374
• /
• 2008

Multi-axial simulation table(MAST) is widely used in motor companies as the multi-axial excitor for vibration fatigue of target component, which provides the vibrational condition as close as the vehicle test. However, the vibration fatigue performance of target component can be guaranteed with MAST system only in case the input profile covers the required severity of the target component on field test. In this paper, the signal processing for multi-axial vibration fatigue test on vehicle component is presented, from the data acquisition of the target component to the derivation of input profile. To compare the severity of vibration condition between field and proving ground, the energy principle of a equivalent damage is proposed and then, it is determined the optimal combination of special events on proving ground using a sequential searching optimal algorithm. To explain the vibration methodology clearly, seat and door component of vehicle are selected as a example.