• 한국의류산업학회지
• /
• 제20권1호
• /
• pp.101-107
• /
• 2018

The purpose of this study is to develop the electroconductive textiles based on polyurethane(PU) nanoweb and to explore that it is applicable to smart clothing. The electroconductive textiles developed by coating 2.0 wt% aqueous dispersed non-oxidized graphene paste on the surface of PU nanoweb. The fabricated electroconductive nanoweb was applied as a transmission line to connect the LED lamp, and the brightness of the LED lamp was measured to confirm its performance. The nanoweb transmission line was fixed by two methods(seam sealing tape, embroidering) to connect the LED lamp and AA batteries. The results as follows, the brightness of the LED lamp fixed with seam sealing tape was about 82 lux, and which fixed with embroidering was about 57 lux. It represents that the nanoweb transmission line which fixed with the seam sealing tape has better electrical signal transmitting because the lux value higher than the one fixed by embroidering. In order to compare the performance of the nanoweb transmission line and the metal wire, we connected the LED lamp with copper wire. The brightness of copper wire connected LED lamp was about 193 lux. Although the electrical signal strength of the nanoweb transmission line was weaker than the copper wire, it was reachable to operate LED lamp. The results of this study will provide a basic data to develop the textile based electronic devices, and conducting wire for smart clothing.

• 한국의상디자인학회지
• /
• 제8권1호
• /
• pp.69-79
• /
• 2006

The purpose of this study is to find the proper width of fabric which can bring high efficiency on productivity. We focus on the marking method by comparing and analyzing the marking efficiency of A-line skirt. This study employs 4 criteria to mark the A-line skirt, which are cutting method, angle, width, and direction, respectively. There can be 2 different cutting methods(fold pattern and add seam pattern at the front and back center line), and 2 different angles(warp angle and bias angle). Also, width of the fabric can be classified into 2 groups(110cm, 150cm), and marking direction can be grouped into 2(one direction marker and one direction per each size marker). These 4 criteria make 16($2^*2^*2^*2$) cases for this study. Main findings are follows. First, the skirt with folded at the center line had higher efficiency rate than the skirt with add seam at the center line. Second, the skirt with the 150cm width has higher efficiency rate than that of 110cm. Third, fixing the warp angle has higher efficiency rate than that of fixing the bias angle at the front and back center line. Finally, one direction per each size marker has much higher efficiency than the one direction marker.

• International Journal of Korean Welding Society
• /
• 제4권1호
• /
• pp.30-37
• /
• 2004

There have been continuous efforts on automating welding processes. This automation process could be said to fall into two categories, weld seam tracking and weld quality evaluation. Recently, the attempts to achieve these two functions simultaneously are on the increase. For the study presented in this paper, a vision sensor is made, a vision system is constructed and using this, the 3 dimensional geometry of the bead is measured on-line. For the application as in welding, which is the characteristic of nonlinear process, a fuzzy controller is designed. And with this, an adaptive control system is proposed which acquires the bead height and the coordinates of the point on the bead along the horizontal fillet joint, performs seam tracking with those data, and also at the same time, controls the bead geometry to a uniform shape. A communication system, which enables the communication with the industrial robot, is designed to control the bead geometry and to track the weld seam. Experiments are made with varied offset angles from the pre-taught weld path, and they showed the adaptive system works favorable results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.844-847
• /
• 2002

본 논문에서는 단상 thyristor 정류기 구조의 대전력 150KVA급의 mash seam 용접기에 용접 센터링등 여러 가지 용접 효율 향상을 위한 부가 장치를 포함한 용접장치 개발을 통한 용접품질 분석결과를 보이고 있다. 일반적으로 제철소에 사용되는 수10KVA급의 용접기들은 그동안 전량 수입에 의존하던 것을 공동연구를 통해서 국산화에 성공하였다. 본 시스템은 기존의 타사제품의 기능을 포함하여 용접 센터링 장치, 용접 전후단 의 크램핑기능, 선후행 코일의 선단부를 절단하는 shear ing 기능, 용접 휠높이 자동조절기능을 포함하였으며, 자체 설계된 대전력용 변압기, 대전력 절환용 thyristor 제어들을 포함한 용접기로써 기존의 타사제품에 비하여 기능적, 성능적으로 향상된 형태로써 용접 성능 검사에서도 양호한 결과 얻었다. 본 논문에서는 mash seam 용접기의 기본적인 기능설명과 개된 용접기를 기능별로 설명하고, 실용접 결과를 소개하여 향후 계획을 제시한다

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.775-778
• /
• 1996

In this research, the robustness of a seam tracking for the automatic welding system is studied. The laser displacement sensor is used as a seam finder. X-Y moving table drived by ac servo motor controls the position and velocity of the torch-and-sensor part. However, dc servo motor is used to control the position and velocity of the torch. The sensor locates ahead of torch to preview the weld line, and brings about the inaccuracy on the torch tracking. To enhance the robustness on this system against the influence of disturbances and model uncertainty, H$\_$.inf./ control is applied to the angular motion of torch. The simulation shows that the tracking accuracy improved significantly. Also, experimental results give a good performance of H$\_$.inf./ control strategy to the automatic seam tracking system for the welding.

• International Journal of Korean Welding Society
• /
• 제1권1호
• /
• pp.31-38
• /
• 2001

For the horizontal fillet welding with one plate in a vertical position, there will be a higher tendency of weld metal falling down rather than for the butt-welding in flat position. Such phenomenon could bring about the overlap or deflection of weld pool, and consequently induce the poor mechanical strength of weldments. Therefore, a precise position control of welding torch in conjunction with the weld qualify plays an important role in welding robot applications. In the present study, an experimental method was proposed for deriving a mathematical model between the leg length and the welding conditions. Finally, an algorithm was proposed for weld seam tracking and improvement of the weld quality. The reliability of the proposed algorithm was evaluated through various experiments, which showed that the proposed algorithm can be very effective for tracking the weld line and simultaneously achieving the sound weld bead.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.771-773
• /
• 2003

본 논문에서는 대전력 150KVA급의 mash seam 용접기에 용접 센터링등 여러 가지 용접 효율 향상을 위한 부가 장치를 포함한 용접장치 개발을 통한 용접품질 분석결과를 보이고 있다. 일반적으로 제철소에 사용되는 수100KVA급의 용접기들은 그동안 전량 수입에 의존하던 것을 공동연구론 통해서 국산화에 성공하였다. 본 시스템은 기존의 타사제품의 기능을 포함하여 용접 센터링 장치, 용접 전후단의 크램핑기능, 선후행 코일의 선단부를 절단하는 shearing 기능, 용접 휠높이 자동조절기능을 포함하였으며, 자체 설계된 대전력용 변압기, 대전력 절환용 thyristor 제어들을 포함한 용접기로써 기존의 타사제품에 비하여 기능적, 성능적으로 향상된 형태로써 용접성능 검사에서도 양호한 결과 얻었다. 본 논문에서는 mash seam 용접기의 기본적인 기능설명과 개발된 용접기를 기능별로 설명하고, POSCO 현장적용 결과를 간략히 소개한다.

• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.70-75
• /
• 2000

The weld seam tracking system for arc welding process uses various kinds of sensors such as arc sensor, vision sensor, laser displacement and so on. Among the variety of sensors available, electro-magnetic sensor is one of the most useful methods especially in sheet metal butt-joint arc welding, primarily because it is hardly affected by the intense arc light and fume generated during the welding process, and also by the surface condition of weldments. In this study, a dual-electromagnetic sensor, which utilizes the induced current variation in the sensing coil due to the eddy current variation of the metal near the sensor, was developed for arc welding of sheet metal butt-joints. The dual-electromagnetic sensor thus detects the offset displacement of weld line from the center of sensor head even though there's no clearance in the joint. A set of design variables of the sensor were determined for the maximum sensing capability through the repeated experiments. Seam tracking is performed by correcting the position of sensor to the amount of offset displacement every sampling period. From the experimental results, the developed sensor showed the excellent capability of weld seam detection when the sensor to workpiece distance is near less than 5 mm, and it was revealed that the system has excellent seam tracking ability for the butt-joint of sheet metal.

• 융합신호처리학회논문지
• /
• 제11권4호
• /
• pp.338-344
• /
• 2010

선박 블록의 용접 공정에서는 용접선의 양쪽 끝이 벽에 의해 막혀있는 경우가 많다. 본 연구에서는 이러한 벽이 있는 환경에서 맞대기 용접의 자동화를 위한 용접선 검출 시스템을 개발하였다. 용접선 검출 시스템은 벽에서 캐리지의 위치를 측정하고, 초층의 용접선을 검출하게 된다. 시스템은 레이저 변위센서와 초음파센서로 구성되어 있다. 레이저 변위센서는 모터에 의해 회전 왕복 운동하며 용접 모재까지의 거리를 측정하게 되고, 초음파센서는 양쪽 벽면까지의 거리를 측정한다. 초음파센서로 측정된 거리정보를 활용하여 용접선의 X(주행)좌표와 용접 시작 및 끝 위치를 판별한다. 그리고 레이저 변위센서에 의해 측정된 거리정보와 센서의 자세정보를 활용하여 용접선의 Y(위빙), Z(높이)좌표를 검출하게 된다. 용접선 검출 시스템은 용접 캐리지와 독립적인 구동을 위해 DSP를 이용하여 별도의 제어기를 구성하였다. 용접 도중 용접선 검출 시스템과 용접 토치(Torch)와 간섭을 피하고, 측정 불가능한 구간이 발생하지 않도록 용접선 검출 시스템을 캐리지의 양쪽에 부착할 수 있게 설계하였다. 최종적으로 용접 캐리지에 부착하고 실험을 수행하여 개발된 용접선 검출 시스템의 효용성을 확인하였다.

• 방송공학회논문지
• /
• 제25권6호
• /
• pp.1004-1012
• /
• 2020

본 논문은 실시간 고해상도 비디오 스티칭을 위한 새로운 콘텐츠 보존 시접선 추정 알고리즘을 제안한다. 시접선 추정은 영상 스티칭 후 중첩 영역에서의 시각적 왜곡을 최소화하기 위한 요소 기술 중 하나이다. 기존 시접선 추정 알고리즘들은 요구되는 연산량과 메모리 사용량이 높은 최적화 알고리즘에 기반을 두고 있음에도 불구하고, 추정된 시접선이 객체를 피하지 못해 객체를 자르거나 반복하는 현상을 유발한다. 또한, 프레임 간의 추정된 시접선의 시간적 일관성이 부족하여 불필요한 잦은 변동이 발생한다. 따라서, 본 논문에서는 직선의 시접선을 활용하여 효율적이고 시간적 일관성이 있으며, 심층신경망 기반 객체 세그먼테이션 알고리즘을 활용하여 객체를 피하여 시접선을 형성하는 시접선 추정 알고리즘을 제안하고자 한다. 고해상도 360° 다중 시점 동영상을 사용한 실험을 통해 제안하는 알고리즘이 기존 알고리즘보다 짧은 시간에 시각적으로 유사한 360VR 동영상을 생성하는 시접선을 추정함을 확인하였다.