• Restorative Dentistry and Endodontics
• /
• v.10 no.1
• /
• pp.127-134
• /
• 1984

This study was conducted to evaluate the sealing ability of McSpadden technique compared with lateral condensation and Engine reamer technique, and according to the degree of canal enlargement and the use and nonuse of sealer. Seventy single-rooted teeth were divided into 14 groups and each tooth was enlarged and obturated according to the purpose of this study. Obturated teeth were infiltrated by Indian ink and decalcified and cleared. The apical sealing ability was evaluated by measuring the degree of ink penetration into the canal. The results were as follows: 1. All the teeth filled by lateral condensation using gutta-percha cone and sealer proved better in canal sealing ability than McSpadden technique and Engine reamer technique, showing less ink penetration. 2. In the McSpadden technique, there was less ink penetration detected in using the sealer than not. 3. In all of the experimental methods, the difference of the degree of ink penetration according the degree of canal enlargement could not be accepted. 4. There was no significant difference in ink penetration degree between Engine reamer technique using sealer and McSpadden technique without sealer.

• Journal of the Korean Ceramic Society
• /
• v.43 no.9 s.292
• /
• pp.544-551
• /
• 2006

The sealing technique between a glass tube and a copper heat pipe in an evacuated tube solar collector is studied. In this study two different sealing techniques, such as flame method and furnace firing, are examined. After the sealing of a copper to a glass, the oxidation state of the copper and its bonding morphology were examined by SEM and XRD. Its oxidation was retarded by coating of borate solution on the copper, and $Cu_2O(cuprite)$ turned into CuO(tenorite) with increase in a firing temperature and firing time. Porous structure was found in the oxide layer when CuO formed. The best sealing morphology was observed when the thickness of the oxidation layer was less than $20{\mu}m$. The sealing technique performed in a furnace was promising and the satisfactory result was obtained when the sample was fired at $950^{\circ}C$ for 5 min under $N_2$ atmosphere. Annealing procedure is recommended to remove the stress left at the bonding zone.

• The Journal of the Korean dental association
• /
• v.23 no.12 s.199
• /
• pp.1031-1037
• /
• 1985

The purpose of this study was to evaluate the marginal sealing ability of 'vivadent.' Using freshly extracted human teeth and 2% aqueous methylene blue, the marginal leakage of dye in restorative materials such as vivadent with acid etching technique, Durafill with acid etching technique, silar with acid etching technique, Adaptic, and Amalgam were investigated at 37℃ and under temperature cycling in range of 4℃-60℃. The results were as follows; 1. All filling materials showed some degree of marginal penetration by 2% methylene blue dye. 2. Vivadent with acid etching technique revealed effective marginal sealing ability, but under temperature cycling it showed increased marginal leakage. 3. All resins showed greater marginal leakage than amalgam restoration. 4. Vivadent had the most effective marginal sealing ability in experimented resins.

• The Journal of the Korea Contents Association
• /
• v.17 no.10
• /
• pp.636-646
• /
• 2017

This thesis aims to create a new technique by applying traditional ceramics technique. As a matter of fact, on the toremi plate of the sieve-frame skein technique, the weld on which various patterns are squeezed, is attached to the cylinder made of clay on the spinning wheel. And it is the concept that maximizes aesthetic beauty by expressing distorted pattern and free dismantling of existing pattern by pushing it out from inside by the turn of electric spinning wheel for the first time.The main point of view of this aesthetic source is that most of the surface of the ceramics is a spherical curved surface and looks distorted like an indicator drawn on a globe. The researcher created a dynamic and humorous technique of expression through the free dismantling of the squashed shapes and the distorted patterns and called it the bating sealing weld outer wall extension technique.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.5
• /
• pp.374-381
• /
• 2016

The sealing technique is widely used for repairing the cracks on the surface of concrete and preventing their expansion in the future. However, it is difficult to ensure the safety of the workers when sealing large structures in inconvenient working environments. This paper presents the development of a sealing robot system to seal various shapes of concrete surface in rough conditions for a long time. If the robot can maintain the desired contact force, the cracks can be completely sealed. An impedance force tracking controller with slope estimator is proposed to calculate the surface slope in real time using the robot position. It predicts the next point in order to prevent the robot from disengaging from the contact surface owing to quick slope changes. The proposed method has been verified by experimental results.

• Restorative Dentistry and Endodontics
• /
• v.8 no.1
• /
• pp.167-172
• /
• 1982

The purpose of this study was to evaluate the marginal sealing ability of "Silar". Using freshly extracted human teeth and 2% acquous methylene blue, the marginal leakage of dye in restorative materials such as Silar, Silar with acid etching technique, Hi-Pol, Hi-Pol Enamel Bond system, Adaptic and Amalgam were investigated at $37^{\circ}C$ and under temperature cycling in range of $4^{\circ}C-60^{\circ}C$. The results as follows; 1. All filling materials showed some degree of marginal penetration by 2% methylene blue dye. 2. Silar with acid etching technique revealed effective marginal sealing ability, but under temperature cycling it showed increased marginal leakage. 3. All composite resins showed greater marginal leakage than amalgam restoration. 4. Silar had the most effective marginal sealing ability in experimented composite resins.

• Journal of the Korean Institute of Gas
• /
• v.16 no.5
• /
• pp.47-51
• /
• 2012

In this study, the deformation behavior stability of sealing rings with three different cross sectional areas has been presented using a FEM technique. To investigate the deformation behavior stability, the initial compression rate of 25% has been applied to the sealing ring, which is molded with a nitrile butadiene rubber. The maximum strain, maximum stress, and maximum contact normal stress have been analyzed for the working fluid pressure of $25kgf/cm^2$. The FEM results show that the maximum strain of a hollow o-ring and a hollow rectangular ring with a hollow space in the center of a sealing ring is higher than that of a conventional o-ring, but the maximum stress and the maximum contact normal stress are low. In these results, the sealing rings with a hollow space in the center of the cross sectional area is recommended to increase an extended endurance stability of sealing rings. But, the solid sealing ring is designed to guarantee the sealing safety of a contact sealing ring.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.1
• /
• pp.150-155
• /
• 2013

This work present a new method of sealing inspection system for vehicle in which foam rubber materials are used for sealing the vehicle parts. This system is composed from a devices comprising non-contact and real-time scanning on visual inspection in machine parts. We have been investigated qualitative factors that influenced on sealing system of vehicle structure which flexibly attenuated vibration and plenty of foam rubber materials having elastic property. However, there are different factors which still depended on outdated technique (personnel subjective judgment) in the performance inspection of rubber parts, specially for cross section inspection. Through a newly developed inspection system which recently applied for the production line, we successfully achieved more effective results of matching rate by about 80 % in the sealing performance inspection with 0.7% to 1.4% in the repeated errors. These are resulted from non-contacted response by CCD camera and vision program using geometry matching method. We expect that this system may be widely applied in the strict inspection parts of more diverse cross-section in future.

• Journal of the Korean Institute of Gas
• /
• v.16 no.5
• /
• pp.52-57
• /
• 2012

This study presents sealing characteristics of multi-contact o-rings as functions of strain, compression stress, and contact normal stress using a FEM technique. The FEM results on the sealing characteristics show that the maximum strain, maximum compression stress, and maximum contact normal stress of multi-contact o-rings are approximately 1.7 times higher than those of conventional o-rings. This is due to a U-grooved cross section of multi-contact o-rings, and the multi-contact o-rings with a U-groove show more effective in sealing for high pressure vessels, valves, and gas equipments. And the extrusion failure in the multi- contact o-ring does not produce for an increased gas pressure due to a U-groove. This may extend sealing life compared to that of a conventional o-ring.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.1
• /
• pp.40-45
• /
• 2012

The glass edge sealing is one of the vacuum glazing core manufacturing process and it needs the high reliability for the vacuum keeping. Conventionally, the glass edge sealing had been being researched by the method that pasted the flit on the glass edge part and bonded two sheets of glass. But this way has the defect that can't make tempered glass. In order to remedy it's faults, in this paper, the glass edge was sealed by using the hydrogen mixture gas torch within the furnace. The parameter having an effect on the glass edge sealing through the basic test was set. And the correlation of the thickness of the glass edge and parameter were analyzed through the design of experiment. By using the Taguchi method, the optimal process condition for the glass edge sealing was drawn and the validity was verified.