• Restorative Dentistry and Endodontics
• /
• 제10권1호
• /
• pp.127-134
• /
• 1984

This study was conducted to evaluate the sealing ability of McSpadden technique compared with lateral condensation and Engine reamer technique, and according to the degree of canal enlargement and the use and nonuse of sealer. Seventy single-rooted teeth were divided into 14 groups and each tooth was enlarged and obturated according to the purpose of this study. Obturated teeth were infiltrated by Indian ink and decalcified and cleared. The apical sealing ability was evaluated by measuring the degree of ink penetration into the canal. The results were as follows: 1. All the teeth filled by lateral condensation using gutta-percha cone and sealer proved better in canal sealing ability than McSpadden technique and Engine reamer technique, showing less ink penetration. 2. In the McSpadden technique, there was less ink penetration detected in using the sealer than not. 3. In all of the experimental methods, the difference of the degree of ink penetration according the degree of canal enlargement could not be accepted. 4. There was no significant difference in ink penetration degree between Engine reamer technique using sealer and McSpadden technique without sealer.

• 한국세라믹학회지
• /
• 제43권9호
• /
• pp.544-551
• /
• 2006

The sealing technique between a glass tube and a copper heat pipe in an evacuated tube solar collector is studied. In this study two different sealing techniques, such as flame method and furnace firing, are examined. After the sealing of a copper to a glass, the oxidation state of the copper and its bonding morphology were examined by SEM and XRD. Its oxidation was retarded by coating of borate solution on the copper, and $Cu_2O(cuprite)$ turned into CuO(tenorite) with increase in a firing temperature and firing time. Porous structure was found in the oxide layer when CuO formed. The best sealing morphology was observed when the thickness of the oxidation layer was less than $20{\mu}m$. The sealing technique performed in a furnace was promising and the satisfactory result was obtained when the sample was fired at $950^{\circ}C$ for 5 min under $N_2$ atmosphere. Annealing procedure is recommended to remove the stress left at the bonding zone.

• 대한치과의사협회지
• /
• 제23권12호통권199호
• /
• pp.1031-1037
• /
• 1985

The purpose of this study was to evaluate the marginal sealing ability of 'vivadent.' Using freshly extracted human teeth and 2% aqueous methylene blue, the marginal leakage of dye in restorative materials such as vivadent with acid etching technique, Durafill with acid etching technique, silar with acid etching technique, Adaptic, and Amalgam were investigated at 37℃ and under temperature cycling in range of 4℃-60℃. The results were as follows; 1. All filling materials showed some degree of marginal penetration by 2% methylene blue dye. 2. Vivadent with acid etching technique revealed effective marginal sealing ability, but under temperature cycling it showed increased marginal leakage. 3. All resins showed greater marginal leakage than amalgam restoration. 4. Vivadent had the most effective marginal sealing ability in experimented resins.

• 한국콘텐츠학회논문지
• /
• 제17권10호
• /
• pp.636-646
• /
• 2017

본 논문은 전통적인 도예기법을 응용하여 새로운 기법을 창안하는데 목적을 둔다. 말하자면 가장 핵심적인 새로운 방법은 체바퀴 타래기법의 토레미판위에 여러 형태의 문양을 압인한 덧살(weld 새롭게 창안한 용어)을 이용하여 물레 위에 소지(역자 주--흙)로 만든 원통에 붙여서 최초로 전기물레의 빠른 회전에 의해 안에서 밖으로 밀어내어 기존 기벽 문양의 자유로운 해체와 왜곡된 문양을 표현하여 미적 아름다움을 극대화하는 컨셉이다. 이러한 미학소스의 주요 관점은 도자기 표면의 대부분 구형태의 곡면인데 마치 지구본에 그려진 지표처럼 왜곡되어 보이는 현상이 일어나는데, 늘려 찌그러진 형태와 왜곡된 문양의 자유로운 표현 해체를 통해 다이나믹하고 역동적이면서 해학적인 표현 기법을 창안하게 되었는데 이 기법을 수레질 압인 덧살 기벽 물레 늘림 기법(bating sealing weld outer wall extension technique)이라고 정하였다.

• 제어로봇시스템학회논문지
• /
• 제22권5호
• /
• pp.374-381
• /
• 2016

The sealing technique is widely used for repairing the cracks on the surface of concrete and preventing their expansion in the future. However, it is difficult to ensure the safety of the workers when sealing large structures in inconvenient working environments. This paper presents the development of a sealing robot system to seal various shapes of concrete surface in rough conditions for a long time. If the robot can maintain the desired contact force, the cracks can be completely sealed. An impedance force tracking controller with slope estimator is proposed to calculate the surface slope in real time using the robot position. It predicts the next point in order to prevent the robot from disengaging from the contact surface owing to quick slope changes. The proposed method has been verified by experimental results.

• Restorative Dentistry and Endodontics
• /
• 제8권1호
• /
• pp.167-172
• /
• 1982

The purpose of this study was to evaluate the marginal sealing ability of "Silar". Using freshly extracted human teeth and 2% acquous methylene blue, the marginal leakage of dye in restorative materials such as Silar, Silar with acid etching technique, Hi-Pol, Hi-Pol Enamel Bond system, Adaptic and Amalgam were investigated at $37^{\circ}C$ and under temperature cycling in range of $4^{\circ}C-60^{\circ}C$. The results as follows; 1. All filling materials showed some degree of marginal penetration by 2% methylene blue dye. 2. Silar with acid etching technique revealed effective marginal sealing ability, but under temperature cycling it showed increased marginal leakage. 3. All composite resins showed greater marginal leakage than amalgam restoration. 4. Silar had the most effective marginal sealing ability in experimented composite resins.

• 한국가스학회지
• /
• 제16권5호
• /
• pp.47-51
• /
• 2012

본 연구에서는 3가지의 서로 다른 단면형상을 갖는 밀봉 링의 변형거동 안정성을 FEM으로 해석하였다. NBR 소재로 제조한 밀봉 링의 변형거동 안정성을 고찰하기 위해 초기 압축률로 25%를 적용하였다. 작동유체의 압력을 최대 $25kgf/cm^2$까지 올렸을 때 발생한 최대변형률, 최대응력, 최대접촉법선응력을 해석하였다. FEM 결과에 의하면, 밀봉 링의 중심부에 빈 공간을 확보한 중공오링과 중공사각링의 최대 변형률은 기존 오링에 비해 높아졌지만, 최대응력과 최대접촉법선응력은 떨어지는 것으로 나타났다. 결국, 밀봉 링이 장수명의 내구 안정성을 확보하기 위해서는 중심부에 빈 공간을 확보하는 것이 권장된다. 그렇지만, 접촉식 밀봉 링의 밀봉 안전성을 확보하기 위해서는 밀봉 링을 하나의 몸체로 설계하는 것이 바람직하다.

• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.150-155
• /
• 2013

This work present a new method of sealing inspection system for vehicle in which foam rubber materials are used for sealing the vehicle parts. This system is composed from a devices comprising non-contact and real-time scanning on visual inspection in machine parts. We have been investigated qualitative factors that influenced on sealing system of vehicle structure which flexibly attenuated vibration and plenty of foam rubber materials having elastic property. However, there are different factors which still depended on outdated technique (personnel subjective judgment) in the performance inspection of rubber parts, specially for cross section inspection. Through a newly developed inspection system which recently applied for the production line, we successfully achieved more effective results of matching rate by about 80 % in the sealing performance inspection with 0.7% to 1.4% in the repeated errors. These are resulted from non-contacted response by CCD camera and vision program using geometry matching method. We expect that this system may be widely applied in the strict inspection parts of more diverse cross-section in future.

• 한국가스학회지
• /
• 제16권5호
• /
• pp.52-57
• /
• 2012

본 연구에서는 유한요소해석법을 사용하여 다접오링의 밀봉특성에 관련된 변형률, 응력, 접촉법선응력을 해석하였다. 밀봉특성에 관한 FEM 해석결과에 의하면, 다접오링에 작용하는 최대 변형률, 최대압축응력, 최대접촉 법선응력은 기존의 오링에 비해 약 1.7배나 더 높게 나타났다. 이것은 다접오링의 절단면에 U홈을 형성하였기 때문이고, 다접오링은 고압가스 용기, 밸브, 가스기기의 밀봉을 유지하는데 매우 유용할 것으로 판단된다. 그리고, 다접오링에서 가스압력을 높여도 압출파손 현상이 발생되지 않았는데, 이것은 U홈이 있기 때문인 것으로 판단된다. 따라서, 다접오링은 기존의 오링에 비해 밀봉수명을 길게 연장시킬 수 있다.

• 한국생산제조학회지
• /
• 제21권1호
• /
• pp.40-45
• /
• 2012

The glass edge sealing is one of the vacuum glazing core manufacturing process and it needs the high reliability for the vacuum keeping. Conventionally, the glass edge sealing had been being researched by the method that pasted the flit on the glass edge part and bonded two sheets of glass. But this way has the defect that can't make tempered glass. In order to remedy it's faults, in this paper, the glass edge was sealed by using the hydrogen mixture gas torch within the furnace. The parameter having an effect on the glass edge sealing through the basic test was set. And the correlation of the thickness of the glass edge and parameter were analyzed through the design of experiment. By using the Taguchi method, the optimal process condition for the glass edge sealing was drawn and the validity was verified.