• 생물환경조절학회지
• /
• 제13권4호
• /
• pp.251-257
• /
• 2004

본 연구는 몇가지 보온피복 재료 및 방법이 플라스틱하우스의 보온력과 토마토의 생육과 수량에 미치는 영향을 구명하고자 수행하였다. 다겹보온덮개(카시미론 8온스 1겹+폴리폼(1 mm) 4겹 +부직포 2겹+폴리프로필렌 1겹+흑색네트차광망 1겹)를 이중하우스 구조의 외면에 피복한 것이 이중하우스 구조의 내부에 피복한 것에 비해 하우스내 야간의 기온과 지온은 약 $ 낮았으나 광투과율이 높아서 토마토 상품수량이 약 $2\%$ 증가하였다. 그리고 다곁보온덮개를 피복하지 않고 이중하우스 구조의 내부에 EVA커튼을 설치한 것에 비해서는 하우스내 야간기온이 $3^{\circ}C$ 높게 유지되어 수확기가 약 1일 빨라지고 토마토 과실도$ 19\%$ 증수하였다. 한편 이중하우스 외면에 다겹보온덮개를 피복하고 내부에 보온커튼(알미늄+직물)을 설치한 것은 다겹보온 덮개를 피복하고 보온커튼을 설치하지 않은 것과 이중하우스에 다겹보온덮개를 피복하지 않고 EVA커튼만 설치한 것에 비해 하우스내 기온이 각각 $2.2^{\circ}C$와 $4.5^{\circ}C$ 높게 유지되었으며 이러한 보온효과에 의해 토마토 과실수량도 각각 $18\%$와 $37\%$ 가되었다. 따라서 본 연구결과는 남부지역에서 저온기에 다겹보온덮개를 이중 플라스틱하우스 구조의 외면에 피복하고 내부에 보온성이 높은 커튼자재를 사용하면 가온을 하지 않거나 최소한의 난방비로 토마토를 재배할 수 있음을 시사해 주었다.

• 한국태양에너지학회 논문집
• /
• 제34권5호
• /
• pp.89-99
• /
• 2014

The determination of the solar and thermal performance of fenestration is required for the evaluation of fenestration energy performance, estimating building load. Presently, there exist several methods for determining the thermal transmission(U-value) and solar heat gain coefficient (SHGC) of fenestration system. These method are commonly grouped under calculation or experimental methods. While U-value testing and calculation methods have been long established, SHGC has been evaluated only by the method of calculation under the lack of any established testing method. However, it is difficult to assess the exact SHGC for various types of fenestration with sun-shading or other solar control systems. The purpose of this study was to evaluate the effect of interior venetian blind and roll screen on the SHGC of glazing system. SHGC has been evaluated by the KS L 9107 test method and exiting calculation method for precise comparison of the energy performances of various shading devices. In this research, the test sample consists of three different types of double glazing unit with venetian blind and roll screen. Slat angles of venetian blind were changed to $-45^{\circ}$, $0^{\circ}$, and$-45^{\circ}$. For the roll screen, measurements were taken with the roll screen in the closed position. In result, the venetian blind reduced SHGC by 21.2~28.4% at $45^{\circ}$, when compared to the double glazing unit. The roll screen reduced SHGC by 34.4~41.7% at closed. The differences between the measured and calculated SHGC were found to range between 0.001(0.2%) and 0.047(11.1%) for all test cases. For the cases of venetian blind $-45^{\circ}$, $0^{\circ}$ and $45^{\circ}$, the deviation ratio were 3.6~9.8%, 1.1~2.6%, 4.2~11.1%, respectively. For the case of roll screen, the deviation ratio were 4.1~5.7%.

• 사물인터넷융복합논문지
• /
• 제7권4호
• /
• pp.85-94
• /
• 2021

본 연구는 스크린 골프에서 그래픽 콘텐츠가 제공하는 이미지 느낌, 표현 방법, 이미지 색상의 고려 정도에 따라 소비자가 경험하는 스크린 골프의 콘텐츠 특성, 재이용 의도, 고객 만족, 경제적 가치에 어떠한 차이가 있는지를 검증하였다. 또한 스크린 골프의 콘텐츠 특성이 경제적 가치에 어떠한 영향 관계가 있고, 이러한 과정에서 재이용 의도와 고객 만족이 어떠한 영향이 있는지를 분석하고자 하였다. 2021년 9월 1일부터 9월 30일까지 스크린 골프장을 이용하는 소비자를 대상으로 225부의 설문조사를 실시하였다. 자료 처리는 빈도분석, 요인분석, 신뢰도분석, 군집분석, 카이제곱분석, 3단계 매개회귀분석을 실시하였다. 연구결과는 다음과 같다. 첫째, 선호하는 이미지 느낌은 깔끔하고 세련된 느낌이 높게 나타났고, 선호하는 표현 방법은 사실적 이미지가 높게 나타났으며, 선호하는 이미지 색상은 초록 계열 색상이 높게 나타났다. 둘째, 그래픽 콘텐츠 고려 정도에 따라 경쟁성, 이용 용이성, 유대감, 현실감에서 차이가 나타났고, 소비자의 재이용 의도, 고객 만족, 경제적 가치에서 차이가 나타났다. 셋째, 스크린 골프 콘텐츠 특성과 경제적 가치의 관계에서 고객 만족과 재이용 의도는 매개효과가 나타났다. 이러한 연구를 통하여 스크린 골프의 그래픽 디자인 모형을 도출할 수 있는 기초자료를 제공함으로써 운영 주체의 경제적 효익이 향상될 수 있는 방안을 제시하였고, 스크린 골프 산업이 성장하는데 기여하고자 하였다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제14권2호
• /
• pp.871-888
• /
• 2020

With the development of display engineering and technology, the screen and sound quality of information devices such as TVs are improving. The screen used LEDs via LCD and PDP and a large flat panel in the early CRT to create super-high resolution. The sound is improved by directly vibrating a thin and simple panel, such as an OLED. In our previous study, the exciter speaker was attached to the rear of the OLED panel to be used as the diaphragm of the speaker, and the sound quality was as good as that of the TV using the existing dynamic speaker. This method supplied the viewer with the direct sound coming from the panel, delivering clear sound, and the sound and image came from the same location, thus giving the viewer high immersion and maximizing the effect of information transfer. OLED exciter speakers, however, have a special directivity, which tends to slightly attenuate the tone at the very center of the screen. This study improves the sound quality by improving the structure of the exciter speaker and the radiated sound of the flat panel display. A 2-in-1 Exciter is made into a single core to improve the speaker's radiation pattern.

• 한국세라믹학회지
• /
• 제53권4호
• /
• pp.381-385
• /
• 2016

Recently, white LEDs, especially, warm white LEDs have been intensively investigated due to outstanding optical properties, long term stability and low power consumption. In this study, mixed type and patterned type of remote phosphors were prepared by screen printing process employing green and red phosphor. Each type of remote phosphor exhibited distinctive photoluminescence spectrum. For example, the mixed type of remote phosphor exhibited unique spectrum, while the patterned type showed expectable spectrum depending on the concentration of phosphors. This indicates that a small amount of red phosphor dramatically reduced the green photoluminescence in the case of mixed-type remote phosphor, whereas the effect was negligible in the patterned-type remote phosphor. The possibility of undesirable chemical reaction was further investigated by using scanning electron microscopy and X-ray diffraction.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.687-687
• /
• 2013

In rearpoint contact solar cell and the PERC (passivated emitter rear contact) type cell, surfaces were passivated by SiO2 or Al2O3 to increase solar cell efficiency. Therefore, we have investigated the effect of surface passivation for crystalline silicon solarcell using mass-production atomic layer deposited (ALD) Al2O3. The patttern which consists of cylinders with 100um diameter and 5um height was formed by PR patterning on Si (100) substrate and then Al2O3 of about 10nm and 20nm thickness was deposited by ALD. The pattern in 10 nm Al2O3 film was removed by dipping in aceton solution for about 10 min but the pattern in 20 nm Al2O3 film was not. The influences of process temperature and heat treatment were investigated using microwave photoconductance decay (PCD) and Quasi-Steady-State photoconductance (QSSPC). The solar cell process used in this work combines the advantage of using the applicability of a selective deposition associated with a ALD passivation and the use of low-cost screen print for the contacts formation.

• Journal of Information Display
• /
• 제7권2호
• /
• pp.16-21
• /
• 2006

The effect of improvement on the surface morphology of screen-printed carbon nanotube (CND) films was studied by using the optically clear poly-dimethylsiloxane (PDMS) elastomer for surface treatment. After the PDMS activation treatment was applied to the diode-type CNT cathode, the entangled carbon nanotube (CNT) bundles were broken up into individual free standing nanotubes to remarkably improve the field-emission characteristics over the as-deposited CNT film. Also, the cathode film morphology of a top gated triode-type structure can be treated by using the proposed surface treatment technique, which is a low-cost process, simple process. The relative uniform emission image showed high brightness with a high anode current. This result shows the possibility of using this technique for surface treatment of large-size field emission displays (FEDs) in the future.

• Molecular & Cellular Toxicology
• /
• 제2권2호
• /
• pp.106-113
• /
• 2006

Phthalate analogues are a plasticizer and solvent used in industry. Phthalates were classified in the category of "suspected" endocrine disruptors. The purpose of our study was to screen and elucidate the endocrine disrupting activity of seven phthalate analogues. E-screen assay was performed in MCF-7 human breast cancer cells with seven phthalate analogues. In this cell proliferation assay, benzyl butyl phthalate (BBP) and dibutyl phthalate (DBP) showed high estrogenic activity. Their relative proliferation efficiencies (RPE) were 109 and 106%, respectively. In vitro estrogen receptor (ER) binding assay, BBP, di-n-octyl phthalate (DOP) and dinonyl phthalate (DNP) showed weak relative binding affinity (RBA: 0.02%) compared to $17{\beta}-estradiol\;(E2)$ (RBA: 100%). In uterotrophic assay, E2 produced a significant increase, whereas four tested phthalate analogues had potential estrogenic effects in vitro did not increased in uterus weight in immature rats. From these results, we demonstrated that phthalate analogues exhibit weak estrogenic activity in vitro assays at high concentrations. Although phthalates induced an increase in MCF-7 cell proliferation by an estrogenic effect, they could not induce a uterus weight increase in vivo. From these, we may suggest that these phthalate analogues are easily metabolized to inactive forms in vivo. Further investigation in other in vitro and in vivo experimental systems might be required.

• 신재생에너지
• /
• 제8권1호
• /
• pp.18-23
• /
• 2012

The screen printing has been widely used to form silver electrodes in solar cell device due to their simplicity of process. However, the wavy and irregular surface which is believed to be originated from a screen mask mesh and thixotropic characteristics of paste on screen printing process is well-known to give a negative effect on solar cell efficiency. The dispensing method that the silver paste is extruded through micro nozzle under a moderate pressure and coated on substrate can form the silver electrode without any wavy surface. In this study, we optimize the composition of silver paste and develop paste blending condition based on the thixotropic behavior of paste. The optimized paste shows a large thixotropic loop area which is related to an aspect ratio of electrode line and has the viscosity of 40 $Pa{\cdot}s$ at 40 s-1. The electrode line we finally obtainis 67.2 ${\mu}m$ in width and has an aspect ratio of 0.277.

• 한국재료학회지
• /
• 제13권10호
• /
• pp.663-667
• /
• 2003

The effects of paste materials on field emission properties in a carbon nanotube(CNT) cathode were investigated for high-efficient field emission displays. The major components in CNT paste for screen printing were a metallic Ag-paste, a dielectric glass-frit and CNT ink. The emission current from the cathode by an electron tunneling effect increased with an increase in the dielectric material fraction in the CNT paste, which is related to an increase of field enhancement factor in Fowler-Nordheim equation. The surface treatment used, after soft baking of the screen-printed CNT films, greatly affected the decrease in the turn-on field in CNT cathode and the uniformity of emission sites over the entire CNT film area.