• Journal of information and communication convergence engineering
• /
• 제13권3호
• /
• pp.189-196
• /
• 2015

In this paper, we present a rotating auto-zeroing offset cancellation technique, which can improve the performance of touch screen sensing circuits. Our target touch screen detection method employs multiple continuous sine waves to achieve a high speed for large touch screens. While conventional auto-zeroing schemes cannot handle such continuous signals properly, the proposed scheme does not suffer from switching noise and provides effective offset cancellation for continuous signals. Experimental results show that the proposed technique improves the signal-to-noise ratio by 14 dB compared to a conventional offset cancellation scheme. For the realistic simulation results, we used Cadence SPECTRE with an accurate TSP model and noise source. We also applied an asymmetric device size (10% MOS size mismatch) to the OP Amp design in order to measure the effectiveness of offset cancellation. We implemented the proposed circuit as part of a touch screen controller system-on-chip by using a Magnachip/SK Hynix 0.18-µm complementary metal-oxide semiconductor (CMOS) process.

• 수산해양기술연구
• /
• 제19권1호
• /
• pp.17-24
• /
• 1983

흑, 적, 녹색의 그물무늬의 시각막을 15.0, 37.4, 62.9cm/sec의 속도로 회전시켰을 때의 송사리 Orizias latipes의 방어 Seriola quinqueradiata의 시각운동반응을 조사한 결과는 다음과 같다. 1. 시각운동반응율은 송사리가 95%, 방어가 94%였다. 2. 송사리가 잘 반응하는 시각막의 색상은 흑, 적, 녹색의 순이며, 흑색에 대한 적, 녹색의 차이는 뚜렷했으나 적색과 녹색의 차이는 뚜렷하지 않았다. 3. 방어가 잘 반응하는 시각막의 색상은 흑, 적, 녹색의 순이며, 색상에 따른 차이는 뚜렷하지 않았다. 4. 시어가 잘 반응하는 시각막의 속도는 62.9, 37.4, 15.0cm/sec의 순이며, 속도에 따른 차이는 뚜렷했다

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.699-702
• /
• 1992

A miniature size electrostatic induction motor have been constructed and studied by applying a three phase ac power source with a maximum voltage of 5 KV and a variable frequency ranged 0.0 - 150 Hz. A maximum no load speed of the motor tested was about 7600 RPM at the applied voltage of 4330 volt and the frequency of 130 Hz for the case of the rotor surface material of polyprophylene sheet screen-printed $TiO_2$ powder on it. It is found that there are 3 different regions of the motor operation, a rotor stop region, a stable operation region and a high speed abnormal region. And it is also found that the motor speed is influenced greatly by the charge relaxation time constant of the rotor surface materials, which however was changed by the means of vapour-deposited Ti or Ni and screen-printed $TiO_2$ powder on the surface of the rotor material, polyprophylene.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 D
• /
• pp.712-714
• /
• 2000

In the field of computer graphics, it approached the investigation of outstanding performance and high speed. Although most introduced Anti-Aliasing method were to meet these, it was not to improve speed. Because Anti-Aliasing method was focus on only qualify. Anti-Aliasing Effect is compensated from movement of object on the screen. Speed is important in the REAL-TIME application program like as 3D games. Cause Anti-Aliasing which needs great amount of time is not used in general. This Paper suggest the Efficient Anti-Aliasing method which apply Two-Point Anti-Aliasing Method that informs brightness data of the screen and use adjacent brightness data for real-time rendering.

• 산업경영시스템학회지
• /
• 제21권48호
• /
• pp.145-152
• /
• 1998

Driving performance is characterized by many things such as driver's experience period, age, ability of information processing and reaction time of control devices and so forth. However, each factor of driving performance is needed to help and screen a poor driver for safe driving. In this paper, driving performance was estimated by reaction of manipulating brake, accelerator, steering wheel and speed. Subjects were grouped by experience of accident and age. Combinations of every group were analysed. For all the dependent variables, only steering wheel and speed were shown to have significant difference, which could be regarded as visual information of speed and direction were the important factors to drive safely. Especially for tile elderly, it is needed to enhance their ability of visual information processing that is to be decreased with aging. Therefore driving simulator to train and screen the poor driver should be studied.

• Ocean and Polar Research
• /
• 제25권spc3호
• /
• pp.399-408
• /
• 2003

The behavior of Suspended Sediment Concentrations (SSC) around a silt screen in a microtidal coastal area was hydrodynamically measured. The current speed at the mid-layer about 30m downstream of the screen reduces to about half that at the same distance upstream. It was caused by the contraction of the vertical section due to the screen. Even during a relatively weak storm period the SSC increases to that of the value caused by dredging. Section-averaged SSC at the downstream of the screen is higher by about 60% than that at the upstream, suggesting that the silt screen plays an adverse effect rather than a constructive role in the reduction of SSC generated by dredging.

• 한국정보통신학회논문지
• /
• 제19권4호
• /
• pp.895-902
• /
• 2015

본 논문은 대형 터치스크린을 위한 고속 터치감지 및 노이즈 제거를 위한 FDCS (Frequency division concurrent sensing) 기법을 제안한다. 기존의 터치스크린 감지방식은 대부분 구동신호를 순차적으로 인가하고 순차적으로 센싱신호를 분석하기 때문에 감지속도가 터치스크린 크기에 따라 급격히 감소하여 대형터치스크린에 적용하기 어려운 문제점이 있다. 제안된 기법은 모든 드라이브라인에 서로 다른 주파수의 신호를 동시에 인가하고 각 센스 라인의 신호를 주파수 영역에서 분석하는 기법으로 대형스크린에서도 고속의 감지속도를 제공한다. 또한 주파수영역에서 노이즈 필터링기법을 제안하여 터치감지신호는 누적하고 노이즈는 상쇄하며, 터치스크린의 주파수전달함수의 역의 특성을 가지는 pre-distortion equalizer를 적용하여 터치감도 SNR을 더욱 개선한다. 23" 대형 터치스크린 모델에 실제의 환경 노이즈를 적용하여 실험한 결과 본 제안기술이 기존 기법 대비 frame scan rate을 274%, SNR을 43dB 증가시킴을 보인다.

• 한국건설순환자원학회논문집
• /
• 제5권4호
• /
• pp.458-465
• /
• 2017

본 연구에서는 굴 패각을 원료(골재)로 활용하기 위한 물리적인 가공방법에 관한 것을 실험을 통해 검토하고자 하였다. 실험결과 굴 패각의 형상에 의해 분쇄된 굴 패각의 적정 입도는 10mm 보다 작아야 될 것으로 판단된다. 또한 가동시간과 회수율, 각 입도별 잔류율과 다양한 입도분포를 고려할 때 굴 패각의 분쇄에는 커터 밀이 적합한 것으로 나타났다. 커터 밀의 경우, 8mm의 내부 스크린을 적용할 때, 회수율은 97.3% 12mm를 적용할 때, 98.2%, 20mm일 때, 98.9%로 나타나 스크린 사이즈가 커짐에 따라 회수율은 다소 증가되는 것으로 나타났다. 커터 밀의 내부 스크린과 인버터의 속도 차이에 의한 실험결과 스크린의 크기가 작을수록, 인버터의 속도가 빠를수록 조립률은 낮아지는 것으로 나타났으며, 동일한 스크린에서 인버터 속도의 상승은 더욱 낮은 입도범위의 재료 회수가 가능한 것으로 나타났다.

• Journal of Biosystems Engineering
• /
• 제7권2호
• /
• pp.72-85
• /
• 1983

Rice whitening is performed by basically two different whitening actions known as abrasive and frictional. The former adopted in the emery stone abrasive type whiteners and the latter in the jet-air friction type. Comparative milling yields and whitening efficiencies between the whitening system consisting of jet-air friction type whiteners only and the system consisting of both abrasive- and jet-air friction-types have not yet been rigorously defined. This study was to examine the effect of combined operations of abrasive- and jet-air friction-type rice whiteners on milling yields and whitening efficiencies. The small capacity commercial units of the abrasive- and friction-type whiteners were used for the experiments. The combinations of whitening treatments were: 1) Once in the abrasive type and then two to three times in the friction type, 2) twice in the abrasive and then two to three times in the friction type and 3) three to five times in friction type. In these tests, counter pressures for the friction type whiteners were established differently as required to get about the same degree of whitening at the end of predetermined numbers of the repeated operations. The speed of emery stone and the slot angle of the screen were also the factors varied in the abrasive type whitener. Sheukwang rice variety having 13.05% M.C. was used in the tests. The dependent variables were the milled- and head-rice recoveries and electricity consumption. The results of the study are summarized as follows: 1. It was found that in the whitening systems consisting of abrasive- and friction-type whiteners slot angle of the screen, the rotational speed of emery stone roller had significant effect on the milling yields and whitening efficiency. In general, the increase of the emery stone roller speed from 690 to 950 rpm presented a positive effect on milling yield, and one-pass abrasive milling combinations had higher milling yields than two-pass abrasive milling combinations. 2. It was apparent that if the slot angle of the screen and the speed of emery stone roller are modified and set at an optimum level, the combination whitening system consisting of abrasive- and friction-type whiteners is better than the pure frictional whitening system consisting of jet-air friction type in terms of milling yields and efficiencies. 3. In the rice whitening system consisting of abrasive- and jet-air friction-type whiteners, the best whitening performance was obtained when the slot angle of the screen and the rotational speed of emery stone roller were $45^{\circ}$ and 950rpm, respectively, for the one-pass abrasive milling combinations. However, for the two-pass abrasive mi11ing combinations, the best performance was obtained with $75^{\circ}$ of slot angle and 950 rpm of the emery stone roller speed. 4. As compared with pure frictional whitening systems, the combination systems produced more milled rice by 0.8-1.0% point and more head rice by 0.5-1.5% point, and consumed less electricity by 0.15-0.20 KwH per 100kg of milled rice when the abrasive whiteners were operated in the modified conditions as described in item 3 above. Further study is recommended to find out optimum operational and design conditions of abrasive type whiterners.

• 반도체디스플레이기술학회지
• /
• 제11권1호
• /
• pp.73-78
• /
• 2012

In this study, the optimal process condition was induced about the pillar arrangement process of applying the screen printing method in the manufacture process of vacuum glazing panel. The high precision screen printing is technology which pushes out the paste and spreads it by using the squeegee on the stainless steel plate in which the pattern is formed. The screen printing method is much used in the flat panel display field including the LCD, PDP, FED, organic EL, and etc for forming the high precision micro-pattern. Also a number of studies of screen printing method have been conducted as the method for the cost down through the improvement of productivity. The screen printing method has many parameters. So we used Taguchi method in order to decrease test frequencies and optimize this parameters efficiently. In this study, experiments of pillar arrangement were performed by using Taguchi experimental design. We analyzed experimental results and obtained optimal conditions which are 4 m/s of squeegee speed, $40^{\circ}$ of squeegee angle and distance between metal mask and glass.