• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.589-593
• /
• 2013

An efficient measurement methodology is proposed to construct the scattering parameters of a multi-port device using a four-port vector network analyzer (VNA) without the external un-terminated ports. By using the four-port VNA, the reflected waves from the un-terminated ports could be minimized. The proposed method significantly enhances the accuracy of the S-parameters with less number of measurements compared to the results of classical renormalization technique which uses two-port VNA. The proposed method is validated from the measured data with the coupled 8-port micro-strip lines.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.1
• /
• pp.9-15
• /
• 2011

This paper suggested the fast and easy method of the dielectric constant measurement for planar dielectrics using a microstrip line. The complex permittivity and permeability were presented by the first reflection and transmission coefficient which were derived from the scattering parameters. This method was verified by the measurement of a known planar dielectric using a microstrip line. This method can be applied to the dielectric constant measurement of unknown planar dielectric.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.2
• /
• pp.101-104
• /
• 1995

In an attempt to understand the nature of hyperthermal ion-surface collisions, noble gas ion beams (He+, Ne+, Ar+, and Xe+) are scattered from a Si(100) surface for collision energies of 20-300 eV and for 45°incidence angle. The scattered ions are mass-analyzed using a quadrupole mass spectrometer and their kinetic energy is measured in a time-of-flight mode. The scattering event for He+ and Ne+ can be approximated as a sequence of quasi-binary collisions with individual Si atoms for high collision energies (Ei > 100 eV), but it becomes of a many-body nature for lower energies, Ar+ and Xe+ ions undergo mutliple large impact parameter collisions with the surface atoms. The effective mass of a surface that these heavy ions experience during the collision increases drastically for low beam energies.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.6
• /
• pp.168-178
• /
• 1994

This paper presents an optical surface roughness sensor developed for intermediate- process measurement on the machine. The light scattering method is adopted for the sensor, which is designed conpact and flexible enough to apply to 'on the machine' measurement of surface roughness. The developed sensor has special features such that it makes use, as the measurement parameter, of the ratio between fluxes of the incident light, and the specularly and partly diffusely reflected light, and that it can adjust the incident light angle. The experimental investigation reveals not only the sensor has good performance as a surface roughness sensor but the sensor is very robust so as to be useful in in-process measurement.

• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.79-84
• /
• 2015

Transformer is widely used element on power system and industrial area. Especially the transformers installed at power system are exposed to an environment of arbitrary changed. Thus the prediction of degradation and the analysis of response to impulse are important. To conduct those works, the electrical characteristics of system should be analyzed, effectively. But the analysis of electrical characteristic in electric machine level such as pole and pad-mounted transformer is almost no, thus commercial VNA (Vector Network Analyzer) is used to getting the response in wide frequency range. However, the output power of VNA is usually under 10mW, so verification for effectiveness of measuring electrically large component should be conducted, firstly. Next, after getting total S-parameter of transformer, predicting impulse response can be performed in time-domain with circuit simulator. In this paper, it is introduced that verification effectiveness of VNA using transfer function from SFRA (Sweep Frequency Response Analyzer), firstly. Next, total S-parameter, six by six matix form, was built using measured 2 port S-parameter from vector network analyzer. To get the response to impulse which is defined by IEC 60060-1, time-domain simulation is conducted to ADS (Advenced Design System) circuit simulator.

• Ocean and Polar Research
• /
• v.33 no.1
• /
• pp.1-11
• /
• 2011

This study describes measurements of fast ice recorded on May 23, 2009, in Kongsfjorden (translated as 'Kongs Fjord'), an inlet on the west coast of Spitsbergen in the Svalbard Archipelago. Seasonal fast ice is an important feature for Svalbard fjords, both in relation to their physical environment and also the local ecosystem, since it grows seaward from the coast and remains in place throughout the winter. Ice thickness, snow, ice properties, and wind speed were measured, while SAR (Synthetic Aperture Radar) data was observed simultaneously observed two times from ALOS-PALSAR (L-band). Measured ice thickness was about 25-35 cm while the thickness of ice floe broken from fast ice was measured as 10-15 cm. Average salinity was 1.9-2.0 ppt during the melting period. Polarimetric data was used to extract H/A/alpha-angle parameters of fast ice, ice floe, snow and glacier, which was classified into 18 classes based on these parameters. It was established that the area of fast ice represents surface scattering which indicates low and medium entropy surface scatters such as Bragg and random surfaces, while fast ice covered with snow belongs to a zone of low entropy surface scattering similar to snow-covered land surfaces. The results of this study will contribute to various interpretations of interrelationships between H/A/alpha parameters and the wave scattering Phenomenon of sea ice.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.298-301
• /
• 2007

Vertical distribution and optical properties of atmospheric aerosols above the Korean peninsula are quite important to estimate effects of aerosol on atmospheric environment and regional radiative forcing. For the first time in Korea, vertical microphysical properties of atmospheric aerosol obtained by inversion algorithm were analyzed based on optical data of multi-wavelength Raman lidar system developed by the Advanced Environmental Monitoring Research Center (ADEMRC), Gwangju Institute Science and Technology (GIST). Data collected on 14 June 2004 at Gwangju ($35.10^{\circ}N$, $126.53^{\circ}E$) and 27 May 2005 at Anmyeon island ($36.32^{\circ}N$, $126.19^{\circ}E$) were used as raw optical data for inversion algorithm. Siberian forest fire smoke and local originated haze were observed above and within the height of PBL, respectively on 14 June 2004 according to NOAA/Hysplit backstrajectory analysis. The inversion of lidar optical data resulted in particle effective radii around 0.32 ${\mu}m$, single scattering albedo between 0.97 at 532 nm in PBL and effective radii of 0.27 ${\mu}m$ and single scattering albedo of 0.92 above PBL. In the case on 27 May 2005, biomass burning from east China was a main source of aerosol plume. The inversion results of the data on 27 May 2005 were found to be particle effective radii between 0.24 ${\mu}m$, single scattering albedo around 0.91 at 532 nm. Additionally, the inversion values were well matched with those of Sun/sky radiometer in measurement period.

• Korean Journal of Remote Sensing
• /
• v.26 no.6
• /
• pp.653-664
• /
• 2010

The land surface reflectance is a key parameter influencing the climate near the surface. Therefore, it must be determined with sufficient accuracy for climate change research. In particular, the characteristics of the bidirectional reflectance distribution function (BRDF) when using earth observation system (EOS) are important for normalizing the reflected solar radiation from the earth's surface. Also, wide swath satellites like SPOT/VGT (VEGETATION) permit sufficient angular sampling, but high resolution satellites are impossible to obtain sufficient angular sampling over a pixel during short period because of their narrow swath scanning. This gives a difficulty to BRDF model based reflectance normalization of high resolution satellites. The principal objective of the study is to add BRDF modeling of high resolution satellites and to supply insufficient angular sampling through identifying BRDF components from SPOT/VGT. This study is performed as the preliminary data for apply to high-resolution satellite. The study provides surface parameters by eliminating BRD effect when calculated biophysical index of plant by BRDF model. We use semi-empirical BRDF model to identify the BRD components. This study uses SPOT/VGT satellite data acquired in the S1 (daily) data. Modeled reflectance values show a good agreement with measured reflectance values from SPOT satellite. This study analyzes BRD effect components by using the NDVI(Normalized Difference Vegetation Index) and the angle components such as solar zenith angle, satellite zenith angle and relative azimuth angle. Geometric scattering kernel mainly depends on the azimuth angle variation and volumetric scattering kernel is less dependent on the azimuth angle variation. Also, forest from land cover shows the wider distribution of value than cropland, overall tendency is similar. Forest shows relatively larger value of geometric term ($K_1{\cdot}f_1$) than cropland, When performed comparison between cropland and forest. Angle and NDVI value are closely related.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.238-242
• /
• 2000

In this paper, the method for dielectric constant and less tangent measurements of microwave substrates using a microstrip line is presented. The two samples of an open-ended line and a short-ended tine are made and complex propagation constant is evaluated from the one-port scattering parameter measurements. This method has been automated fully using a personal computer and a vector network analyzer.

• Korean Journal of Metals and Materials
• /
• v.49 no.4
• /
• pp.275-280
• /
• 2011

This paper focuses on reliability prediction of long-term creep strength for Modified 9Cr-1Mo steel (Gr. 91) which is considered as one of the structural materials of next generation reactor systems. A "Z-parameter" method was introduced to describe the magnitude of standard deviation of creep rupture data to the master curve which can be plotted by log stress vs. The larson-Miller parameter (LMP). Statistical analysis showed that the scattering of the Z-parameter for the Gr. 91 steel well followed normal distribution. Using this normal distribution of the Z-parameter, the various reliability curves for creep strength design, such as stress-time temperature parameter reliability curves (${\sigma}$-TTP-R curves), stress-rupture time-reliability curves (${\sigma}-t_{r}-R$ curves), and allowable stress-temperature- reliability curves ([${\sigma}$]-T-R curves) were reasonably drawn, and their results are discussed.