• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.162-163
• /
• 2002

1-D photonic band-gap structure is identified in a cholesteric liquid crystal system. The optical transmission spectrum is measured and compared with the theoretical analysis. Nonlinear transmission is measured near the band edge. Also 3-D photonic band-gap structures are fabricated from dielectric colloidal polystyrene beads through a centrifuge method. The fabricated photonic crystals exhibit opalescent colors under white light and show a clear diffraction peak dependent on the incident angle of the light beam. Also the scanning electron microscope image was taken to verify the face-centered cubic crystal structure. Bragg's law and Snell's law are employed to describe the position of angle resolved diffraction peaks. It was shown that the optically deduced effective refractive index and lattice constants were in good agreement with the crystal structure identified by scanning electron microscope.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.349-354
• /
• 2001

In this study, we investigated the effect of the impacting ang1e of particles, the scanning times and the stand-off distance on the surface roughness and the weight-loss rate of samples with no mask, and the wall profile and overetching of samples with different mask pattern in powder blasting of soda-lime glass. The varying parameters were the different impact angles between 50$^{\circ}$ and 90$^{\circ}$, scanning times of nozz1e up to 40 and the stand-off distances 70mm and 100mm. The widths of mask pattern were 0.2mm, 0.5mm and 1mm. The powder was alumina sharp particles, WA#600. The mass flow rate of powder during the erosion test was fixed constant at 175g/min and the blasting pressure of powder at 0.2MPa

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.2E
• /
• pp.21-26
• /
• 1997

We propose to use transverse waves instead of longitudinal waves in a scanning tomographic acoustic microscope (STAM) and new type of multiple-transducer with the functions of muliple-angle and multiple-frequency tomography. Proposed multiple-transducer scheme has three insonification angles and three resonance frequencies in order to operate in the transverse wave mode and multiple-angle and multiple frequency tomography for the STAM. In order to evaluate the performance of proposed transducer scheme we have simulated tomographic reconstruction with back-and-forth propagation(BFP) algorithm. Simulation results showed proposed multiple-transducer scheme is capable of obtaining good resolution with transverse wave mode and multiple-frequency tomography. It is also showed that proposed scheme is an efficient rotation scheme by proportion to the number of projections.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.15-16
• /
• 2003

3-D photonic band-gap structures are fabricated from dielectric colloidal polystyrene beads through a centrifuge method. The fabricated photonic crystals exhibit opalescent colors under white light and show a clear diffraction peak dependent on the incident angle of the light beam. Also the scanning electron microscope image was taken to verify the face-centered cubic crystal structure. Bragg's law and Snell's law are employed to describe the position of angle resolved diffraction peaks. It was shown that the optically deduced effective refractive index and lattice constants were in good agreement with the crystal structure identified by scanning electron microscope.

• International Journal of Advanced Culture Technology
• /
• v.7 no.4
• /
• pp.302-307
• /
• 2019

In this paper, we propose an efficient method for AR toolkit Vuforia. In order to increase the scan rate when using the 3D object scanner, the scan rate parameters need to be analyzed in terms of the angle and distance. In addition, in order to increase the tracking rate when tracking an object, the tracking rate has to be evaluated according to the position, complexity, and contrast of the object. To this end, we have defined the difference of scan rate according to angle and distance between camera and object when using object scanner and the recognition time according to object's position, complexity and contrast when tracking object.

• Applied Microscopy
• /
• v.24 no.3
• /
• pp.87-93
• /
• 1994

In order to elucidate the machinability of lead brass, orthogonal machining experiment was conducted in SEM(Scanning Electron Microscope) equipped with a micro-machining device at a cutting speed of $7{\mu}m/s$ for brass containing 0.2 to 3wt% Pb. The microfactors (i.e., shear angle, contact length between chip and tool) were determined by in-situ observations. Machinability of brass containing lead is discussed in terms of the microfactors and the cutting resistant force tested by lathe cutting. The dynamic behavior of the chip formation of lead brass during the machining process was examined: The chips of lead brass form as a shear angle type. The shear angle increases with the content of lead in (6:4) brass. The pronounced effect of lead on the contact length between chip and tool was observed above 1% Pb. The cutting resistant force tested by lathe decreases remarkably with the lead content in brass. The observed microfactors are in close relation to the tested resistant force in macromachining.

• Proceedings of the KSRS Conference
• /
• v.1
• /
• pp.386-389
• /
• 2006

The sea surface wind speed (SSWS) derived by microwave radiometer can be contaminated by change of microwave brightness temperature owing to the angle between the sensor azimuth and the wind direction (Relative Wind Direction). We attempt to correct the contamination to the SSWS derived by Advanced Microwave Scanning Radiometer (AMSR) on Advanced Earth Observing Satellite II (ADEOS-II), by applying the method proposed by Konda and Shibata (2004). The improvement of accuracy of the SSWS estimation amounts to roughly 60% of the error caused by the RWD effect.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.4
• /
• pp.339-347
• /
• 2012

In previous studies, methods for enhancing cellular response on the Hydroxyapatite coated implant surface were described. In this study, the changes of surface characteristics such as surface roughness, contact angle, surface energy and surface morphology were observed when Hydroxyapatite coated Ti discs were immersed in NaCl solution for various time. Hydroxyapatite coated Ti discs were immersed in 0.9% NaCl solution for 7, 14 and 21 days at $37^{\circ}C$. The control group comprises dry identical discs not immersed in a solution. (n=3) All discs were dried in air completely and the surface roughness was measured using confocal laser scanning microscopy(CLSM). Static contact angle was recorded by video contact angle analyzer after dropping distilled water on the surface. The surface energy was calculated from contact angles of the three liquids. Surface was observed using a field emission-scanning electron microscope(FE-SEM). As a result, the surface roughness of immersed Hydroxyapatite coated Ti discs increased significantly and the contact angle decreased comparing with control group discs. The surface energy of immersed discs increased except for discs immersed for 14 days.

• Journal of Information Technology Services
• /
• v.11 no.sup
• /
• pp.103-111
• /
• 2012

In epigraph field to study ancient scripts, alternative readability improvement technologies have been developed to replace existing rubbing method which has low resolution and causes surface pollution of heritages from the viewpoints of extraction process and used materials. Recently many methods which are based on analysis of pixel data for extracting outlines of the specific image have been developed with advancement of image processing techniques. But these methods are not applicable and the results are not satisfied in the damaged inscriptions which are weathered by wind and rain for a long time and in the narrowed one. In this paper laser scanning techniques which uses optical triangulation measurement principle are developed to minimize scanning error. The proposed techniques are consisted of 3 parts：(1) the understanding of optical triangulation measurement principle to find scanning guideline (2) determinations of points interval, scanning distance and scanning angle to guarantee scanning data quality (3) identification of valid point data area which will be used in registration process. The proposed character identification method contributed in decoding an ancient inscription on SeukBingGo in Kyungju.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.02a
• /
• pp.281-282
• /
• 2008

The glancing angle deposition (GLAD) technique was used to fabricate $ZrO_2$ thin films by electron-beam evaporation. The crystal structure, cross-sectional structure, surface morphology and optical properties are characterized by X-ray diffraction meter (XRD, Rigaku, Cu $K{\alpha}$ - radiation), scanning electron microscope (SEM), and spectrophotometer, respectively.