• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.173-174
• /
• 2006

High power amplifier (HPA), which is used in transmitter of wireless communication systems, usually works in near saturation point in order to achieve maximum efficiency. In this region, HPA can introduce undesirable nonlinear effects. In this paper, we present a polynomial modeling method for efficient techniques to compensate for nonlinear distortion introduced by nonlinear HPA. Proposed polynomial predistorter inverses actual amplifier. Namely, we derive polynomials of amplifiers from analytical method and the electrical parameters in the data sheet of an actual amplifier and then can derive polynomial predistorter by inversing them. It is an effective and a simple method to compensate nonlinear distortion. SSPA(Solid-state power amplifier) is considered. We also analyze the effects of predistortion on the SER performance of communication system with 16-QAM modulation format. The results have shown the efficiency of this model.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.3
• /
• pp.5-11
• /
• 2003

A simulation model for radial magnetic bearings is presented. The model incorporates hysteresis, saturation and eddy current effects. A simple magnetization model that describes hysteresis and saturation is proposed. Eddy currents are taken into consideration by assuming that they are generated by single-turn fictitious coils wrapped around each magnetic flux path. The dynamic equations describing the simulation model can easily incorporate the operation of switching power amplifier. A simulation of a typical 8-pole radial magnetic bearing produces switching waveforms very similar to the experimental observation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2382-2390
• /
• 2007

A new polynomial-based predistortion method for linearizing nonlinear power amplifier is proposed. The proposed method finds the predistortion parameter directly without the help of postdistorter whereas most existing polynomial-based predistortion methods calculate the predistortion parameter indirectly from the prostdistorter. First, a new predistortion algorithm is derived based on the assumption that the characteristic of the amplifier is modeled by piecewise linear function. Then it is modified into a proposed method which does not require any assumption or prior knowledge of the amplifier. The proposed method is derived based on the RLS (recursive least squares) algorithm. The proposed technique is simpler to implement than the existing methods and the computer simulation demonstrates that the proposed method is more robust to the initial condition and the saturation region of the amplifier.

• Korean Journal of Optics and Photonics
• /
• v.10 no.4
• /
• pp.294-300
• /
• 1999

The density matrix is solved more rigorously, compared with the third-order pertubation method used in the conventional theory, for a semiconductor laser amplifier. Then the coupled wave equations are derived to explain the wavelength conversion due to the spectral hole burning in the semiconductor optical amplifier. It is shown that our results can explain the effect of saturation of the population density on the electric polarization, which affects the four-wave mixing and wavelength conversion, better than the conventional theroy where the third-order pertubation is used.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.4
• /
• pp.143-150
• /
• 2014

A high power amplifier(HPA) has widely been used in wireless communications. In order to have a maximum power efficiency, the HPA uses a saturation domain having nonlinear characteristics, which generates nonlinear distortions to decrease the transmission efficiency. In order to solve this problem, various methods to linearize HPA have been reported until now, and the pre-distorter method is very attractive among them. In this paper, a new enhanced adaptive pre-distorter method was proposed to be applied for compensating nonlinear distortions of HPA. Through computer simulations as well as the analytical analysis, it could be shown that it is possible for both conventional adaptive pre-distorter and proposed adaptive pre-distorter, to be applied for linearizing HPA. Also, the simulations results demonstrated that the proposed adaptive pre-distorter may have faster convergence speed and better capability of compensating the nonlinear distortion than the conventional adaptive pre-distorter with nearly equal computation complexity.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.375-376
• /
• 2009

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.02a
• /
• pp.312-313
• /
• 2004

The optical gain saturation and noise figure characteristics of 1550nm traveling-wave semiconductor optical amplifiers are analyzed experimentally and theoretically. The result shows that there is an optimum active layer thickness for high saturation output power and low noise figure.

• Current Optics and Photonics
• /
• v.5 no.2
• /
• pp.141-146
• /
• 2021

We have evaluated the suppression effect of atmospheric-turbulence-induced optical scintillation in terrestrial free-space optical (FSO) communication systems using a gain-saturated erbium-doped fiber amplifier (EDFA). The variation of EDFA output signal power has been measured with different amounts of gain saturation and modulation indices of the optical input signal. From the measured results, we have found that the peak-to-peak power variation was decreased drastically below 2 kHz of modulation frequency, in both 3-dB and 6-dB gain compression cases. Then, the power spectral density (PSD) of optical scintillation has been calculated with Butterworth-type transfer function. In the calculation, different levels of atmospheric-turbulence-induced optical scintillation have been taken into account with different values of the Butterworth cut-off frequency. Finally, the suppression effect of optical scintillation has been estimated with the measured frequency response of the EDFA and the calculated PSD of the optical scintillation. From our estimated results, the atmospheric-turbulence-induced optical scintillation could be suppressed efficiently, as long as the EDFA were operated in a deeply gain-saturated region.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.172-175
• /
• 2010

본 논문에서는 GaN HEMT를 이용하여 Jamming용 System에 사용될 수 있는 고효율 및 고출력 특성을 가지는 광대역 Amplifier를 제작하였다. Jamming System에서 핵심이 되는 Amplifier는 넓은 범위의 주파수에서 통상적으로 사용되는 출력 신호에 비해 보다 높은 출력의 신호를 구현하는 것이 중요하다. 본 논문에서는 GaN HEMT에 안정적인 전원 공급을 위한 음 전원 Bias 제어 회로와 Sequence 회로 및 온도에 따른 Gain 보상 회로를 구현하였으며, 500~2500MHz의 광대역에서 동작하면서 50W 이상의 출력을 낼 수 있도록 설계하였다. 출력 전력이 향상과 안정적인 동작을 위해 Main 출력 단은 60Watt 급의 GaN HEMT 소자와 광대역 Coupler를 이용하여 Balanced Structure로 설계하였다. 제작된 광대역 Amplifier는 30V 단일 전원에서 동작하도록 설계되었고, 크기는 140*90mm이다. 동작주파수 대역(500~2500MHz)에서 Small Signal Gain 63dB와 Gain Flatness ${\pm}$2dB, -10dB 이하의 Input Return Loss를 가진다. CW(Continuous Wave) Signal을 이용하여 측정하였으며, 50Watt 이상의 Saturation Power에서 최대 45%, 최소 28% 정도의 효율 특성을 보였다.

• Current Optics and Photonics
• /
• v.6 no.1
• /
• pp.32-38
• /
• 2022

Erbium-doped fiber amplifiers (EDFAs) have saturated the technological market but are still widely used in high-speed and long-distance communication systems. To overcome EDFA saturation and limitations, its erbium-doped fiber is co-doped with other materials such as zirconia and bismuth. This article demonstrates and compares the performance using three different fibers as the gain medium for zirconia-erbium-doped fibers (Zr-EDF), bismuth-erbium-doped fibers (Bi-EDF), and commercial silica-erbium-doped fibers (Si- EDF). The optical amplifier was configured with a double-pass amplification system, with a broadband mirror at the end of its configuration to allow double-pass operation in the system. The important parameters in amplifiers such as optical properties, optical amplification and noise values were also examined and discussed. All three fibers were 0.5 m long and entered with different input signals: 30 dBm for low input and 10 dBm for high input. Zr-EDF turned out to be the most relevant optical amplifier as it had the highest optical gain, longest transmission distance, highest average flatness gain with minimal jitter, and relevant noise figures suitable for the latest communication technology.