• Journal of Welding and Joining
• /
• 제16권1호
• /
• pp.125-133
• /
• 1998

The effect of volume fraction of Cr carbide phase (Cr CVF) on the low stress abrasion resistance in the chromium-carbide-type high Cr white iron hardfacing weld deposits has been investigated. In order to examine Cr CVF, a series of alloys with varying Cr CVF by changing chromium and carbon contents and the ratio of Cr/C were employed. The alloys were deposited once or twice on a mild steel plate using the self-shielding flux cored arc welding process. The low stress abrasion resistance of the alloys against sands was measured by the Dry Sand/Rubber Wheel Abrasion Test (RWAT). It was shown that hardness and abrasion resistance increased with increasing Cr CVF within the whole test range (Cr CVF : 0.23-0.64). Both primary Cr carbide and eutectic Cr carbide were particularly effective in resisting wear due to their high hardness.

• 보존과학회지
• /
• 제37권6호
• /
• pp.738-747
• /
• 2021

제철원료별 직접제련법 복원실험으로 생산된 단조박편의 재료과학적 분석을 통해 금속학적 특성을 규명하였다. 제련을 위해 경주감포사철과 양양철광석을 이용하며, 각각 4개의 그룹을 설정하였다. 분석은 주성분, 광물 동정, 미세조직 관찰을 하였다. 주성분 분석 결과 정련·단접이 진행될수록 Fe의 함량은 증가하고 비금속개재물의 함량은 감소하였다. 광물을 동정한 결과 산화철 계열의 광물이 확인되었다. 미세조직 관찰 결과 Wüstite, Fayalite가 관찰되었으며, 일부에는 응집된 Wüstite가 관찰되었다. 일부 다각형, 장주상의 Magnetite도 확인되었다. 또한, 공극 및 불순물, 비금속개재물은 점차 감소하였다. 차후 다양한 제철원료를 이용한 복원실험을 통해 생산된 단조박편의 재료과학적 분석을 통해 금속학적 특성을 규명하고, 이를 유적에서 출토된 단조박편과 비교·검토하는 것이 필요하다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 봄 학술발표회 논문집
• /
• pp.148-151
• /
• 1994

Up to now, sea sand without complete removal of salt is being used in the construction works because there is little satisfactory counterplan for the substitute aggregate. In the case that such sea sand is used in the reinforced concrete, the residual salt gives rise to deterioration phenmenon and iron corrosion, reducing durability of the ferro-concrete structures. The paper, an experimental study on the effect of corrosion protection by tighting concrete used SF and FA, is to investigate general steel bar's corrosion and to develop concrete using sea sand economically after it is analyzed and examinated ratio of the corrosion area affected by the autoclave cycle. As a test results, as for corrosion area ratio, it is very effective to use admixrutes such as SF and FA which decrease corrosion area remarkably with increasing the amounts of admixtures. Accordingly the use of admixtures is advantageous for tightening concrete and has an effect of salt damage prevention and rust protection in concrete used sea sand.

• 자원환경지질
• /
• 제38권5호
• /
• pp.571-577
• /
• 2005

철산화물 피복 모래를 이용한 투수성 반응 벽체는 As(V)로 오염된 지하수의 처리에 매우 효과적인 것으로 알려져 있다 그러나 이 방법은 As(III)에 있어서는 그 제거효과가 제한적인 실정이다. 본 연구에서는 위 방법에 의한 3가 비소제거의 한계를 극복하기 위해서 As(III)를 As(V)로 산화시킬 수 있는 능력을 가진 망간산화물 피복 물질을 비소저감 촉진제로서, 철산화물 피복 물질을 이용한 처리 기법에 함께 적용하였다. 철산화물 피복 모래와 망간산화물 피복 모래를 함께 이용한 비소제거 방법으로서, 순차 제거법과 동시 제거법이 연구되었다. 두 가지 처리 방법 모두 6시간동안 $85\%$ 이상의 높은 비소제거 효율을 보였으며, 처리과정 동안 흡착제 표면의 철이나 망간의 용해에 의한 2차적인 오염도 일어나지 않았다. 그러나, 동시 제거법은 비소 저감 후 처리수의 산성도를 pH 6.0의 중성상태로 유지하는 반면, 순차 제거법은 처리수를 pH 4.5의 산성상태로 변화시키는 작용을 일으켜, 음용수로서의 이용을 위한 오염 지하수의 비소 저감법으로는 동시 제거법이 적합한 것으로 판정되었다. 보다 높은 As(III) 제거 효과를 위해, 망간 및 철산화물을 폴리프로필렌 섬유에 피복시켜 비소제거에 적용하였다. 폴리프로필렌 섬유는 높은 표면적과 낮은 비중의 특성을 가진, 신축성 있는 스폰지와 같은 저렴한 중합체의 일종이다. 이를 이용한 비소 제거법은 피복모래를 이용한 방법보다 월등히 뛰어난 $99\%$ 이상의 높은 비소제거 효율을 나타내었다. 또한, 피복 폴리프로필렌 섬유를 이용한 방법은 비소에 오염된 물의 음용수로의 이용을 위한 간편한 처리기법으로서 적용하기에 좋은 많은 실용적인 장점들을 가지고 있다.

• 대한토목학회논문집
• /
• 제32권1B호
• /
• pp.85-91
• /
• 2012

영가철을 이용한 투수성 반응벽체는 지하수를 처리하는 원위치정화기술로 국내외적으로 연구가 활발히 진행되고 있다. 본 연구는 기존 영가철을 이용한 투수성 반응벽에 직류전원을 공급하여 효율이 향상된 TCE 처리기술 개발을 목적으로 하였다. 주문진규사로만 충진한 컨트롤컬럼, 영가철과 주문진규사로 충진한 영가철컬럼(영가철:주문진규사 = 1:2(v/v)) 그리고 영가철 컬럼에 직류전원을 공급한 복극전기분해컬럼, 이 세 컬럼의 운전을 통해 TCE 분해효율을 비교하였다. 실험 결과, 영가철를 충진하고 직류전원을 공급한 복극전기분해컬럼이 영가철만을 사용한 컬럼에 비해 높은 TCE의 환원효율을 나타내었다. 이는 영가철 입자가 미세전극으로 작용하여 전자의 이동을 촉진시킨 것에 기인한 것으로 보인다. 따라서 영가철이 반응매질로서의 역할만 할 때보다 반응매질의 역할과 동시에 전극으로서 작용했을 때, TCE 분해효율이 더 높게 나타났음을 알 수 있었다.

• 한국주조공학회지
• /
• 제24권1호
• /
• pp.52-59
• /
• 2004

Microstructure and mechanical properties of ductile cast iron were investigated in terms of diameter change of samples that gives rise to modify the microstructure due to different cooling rate in the continuous casting process. The chemical composition used in this study was GCD 400 grade. From the microstructural observation, we have found a large number of graphite with small size in diameter which is comparable to the microstructure of the sample produced by conventional sand casting. The major reason of this would he due to high cooling rate. In the sample with 26 mm in diameter, the microstructure was composed of pearlite, iron carbide, and graphite. In the samples with 60 and 100 mm in diameter, however, we have observed a dissimilar microstructure that consisting of ferrite and graphite. Concerning the mechanical property, the sample with 26 mm in diameter showed higher hardness and strength compared to those samples with 60 and 100 mm in diameter. The result obtained for ductility appeared a reversal. Much more works such as inoculation, process design and chemical composition would be required in order to have a sound product even in a small diameter of samples.

• 상하수도학회지
• /
• 제22권3호
• /
• pp.379-387
• /
• 2008

The pH & alkalinity adjustment method by lime and carbon dioxide($CO_2$) for corrosion control in water distribution system was investigated to evaluate the corrosion characteristics of metal pipes, such as galvanized iron, copper, stainless steel, and carbon steel. When the pH in sand filtered and ozone+GAC treated water was increased with lime and $CO_2$ from 7.5 to 8.0, the concentration of residual chlorine decreased at higher pH and longer reaction time; the concentration of trihalomethane increased. The corrosion rate of coupons with corrosion control using lime and carbon dioxide was showed much smaller than those without corrosion control using pilot-scale simulated distribution system. The galvanized iron was corroded much faster than carbon steel, copper, and stainless steel. Especially, copper and stainless steel coupons were hardly corroded. The galvanized iron and carbon steel coupons with corrosion control were produced the corrosion products less than those without corrosion control by the results of environmental scanning electron microscope(ESEM) and energy dispersive x-ray spectroscopy(EDS) analyses. The galvanized iron coupon with pH and alkalinity adjustment by lime and carbon dioxide was detected about 30 percent of zinc, when the carbon steel was detected about 30 percent of calcium by calcium carbonate products formation. For the results of X-ray diffraction(XRD) analyses, the goethite(${\alpha}$-FeOOH) was identified as primary corrosion product of galvanized iron without corrosion control, while the Zinc oxide(ZnO) was found on corrosion products of galvanized iron coupon with corrosion control as the results of EDS analyses. However, the carbon steel corrosion products regardless of corrosion control were composed predominantly of maghemite(${\gamma}-Fe_2O_3$) and hematite(${\alpha}-Fe_2O_3$).

• 한국주조공학회지
• /
• 제4권4호
• /
• pp.20-29
• /
• 1984

It is very important to obtain gray and ductile cast irons with completely pearlitic structure by addition more economical alloying elements. In this study, 9 melts of gray iron and 5 melts of Mg-treated ductile cast iron were made according to Sb content (0-0.08% Sb). Each melt were casted to ${\phi}20mm$ test bars in sand mold under the same condition and inspected microstructure, mechanical and thermal properties. The results obtained from this study are as follows: 1. It is confirmed that Sb should be an economical, simple and useful additive for avoiding ferrite in gray and even in ductile cast irons. 2. For gray cast iron, the recommended ladle addition of metallic Sb amounts to 0.05%. At these levels, Sb has no detrimental influence on the mechanical properties of gray cast irons, which are normally modified according to their pearlite content without increasing the chilling tendency. 3. Despite its adverse influence on graphite shape in ductile iron, Sb can be used as a pearlite stabilizing alloying element even in the case of Mg - treated iron. The quantity to be added does not exceed 0.04% in the case of thinwalled castings. 4. The nodule count is increased very much and the shape of graphite particles become remarkably spheroidal. The matrix may be fully pearlitized, except for thin - walled castings, because the high nodule count results inevitably in some ferrite. 5. The $Ac_1$ and pearlite decomposition temperature are rised in accordance with increasing of additive Sb amount.

• 상하수도학회지
• /
• 제18권3호
• /
• pp.307-311
• /
• 2004

The objective of this work is to evaluate the hypothesis that a good technique for supplying oxygen to the saturated zone in the presence of light nonaqueous phase liquid (LNAPL) pool contamination at the water table is to pass air through the unsaturated zone above the pool. This hypothesis was evaluated in experimental studies performed using a bench-scale, sand-tank reactor, Steady-state abiotic experiments in the sand-tank reactor with air flowing through the reactor headspace demonstrated that oxygen supply through the water table interface into the saturated zone was enhanced when an LNAPL (dodecane) pool was present at the water table. These experimental results confirmed the hypothesis that an LNAPL pool can serve as a high concentration oxygen source to the oxygen-limited area beneath the pool and, as a result, enhance the in situ biodegradation rate.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.199-200
• /
• 2002

Three-body abrasive wear resistance of mild steel, low alloy steel (Bisalloy) and 27%Cr white cast iron was investigated using a ball-cratering test. Glass beads, silica sand, quartz and alumina abrasive particles with sizes larger than $100{\mu}m$ were used to make slurries. It was found that the wear rates of all three materials tested increased with time when angular abrasive particles were used and were rather constant when round particles were used. This increase in wear rates was mainly due to the gradual increase in ball surface roughness with testing time. Abrasive particles with higher angularity caused higher ball surface roughness. Mild steel and Bisalloy were more affected by this ball surface roughness changes than the hard white cast iron. Generally, three-body rolling wear dominated. The contribution of two-body grooving wear increased when the ball roughness was significant. More grooves were found when round particles were used or the size of the particles was decreased.