• Korean Journal of Environmental Biology
• /
• v.24 no.3
• /
• pp.258-267
• /
• 2006

Distribution of population densities of heterotrophic bacteria, E. coli, and Salmonella and Shigella in seawater and sediments at 40 stations near Samcheonpo Bay were measured for 3 times from July to December, 2003. Population densities of heterotrophic bacteria in seawater during survey periods were in the range of $1.7{\pm}0.9{\times}10^3{\sim}2.4{\pm}0.9{\times}10^5$ CFU $mL^{-1}$ and the highest density was shown at St. 34 during the sampling period of September, 2003. Population densities of heterotrophic bacteria were shown higher values on September than those of July and December at all sampling stations. Population densities of anaerobic heterotrophic bacteria in sediments during survey periods were in the range of $2.2{\pm}0.2{\times}10^3{\sim}2.0{\pm}0.2{\times}10^5$ CFU $mL^{-1}$ and their population densities at sampling stations far from Samcheonpo Bay measured lower values than those near Samcheonpo Bay. Population densities of anaerobic heterotrophic bacteria in the sediments were not affected by physico-chemical factors of upper water environment. E. coli were detected only at 8 stations in seawater and 4 stations in the sediments among 40 sampling stations on July and were not detected during September and December. Salmonella and Shigella were detected only a few stations on July and September during sampling periods.

• Journal of The Geomorphological Association of Korea
• /
• v.28 no.2
• /
• pp.15-30
• /
• 2021

This study tried to reveal distribution of incision rate and the factors from fluvial terrace deposits on the western and eastern slopes in the Middle Sobaek Mountain Range, using OSL age dating and topographical analysis. An average incision rate of 0.220 m/ka was estimated in the western slope streams, while the streams on the eastern slope showed a lower average incision rate of 0.121 m/ka. These results seem to indicate that the study area experienced an asymmetric uplift. Patterns of incision rate in the study area were different from those in the Northern Sobaek Mountain Range, probably suggesting that the Sobaek Mountain Range experienced spatially different uplift patterns. Among the factors, which were considered to influence on distribution of incision rate in the study area (e.g., altitude of sampling point, distance from divide, distance from axis, channel width, and bedrock type), distance from axis showed the strongest relationship with incision rate. Therefore, uplift is thought to be the most significant factor in distribution of incision rate in the Middle Sobaek Mountain Range.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.214-221
• /
• 2010

Radio frequency (RF) subsampling can be used by radio receivers to directly down-convert and digitize RF signals. A goal of a cognitive radio/software defined ratio (CR/SDR) receiver design is to place the analog-to-digital converter (ADC) as near the antenna as possible. Based on this, a band-pass sampling (BPS) frontend for CR/SDR is proposed and verified. We present a receiver architecture based second-order BPS and signal processing techniques for a digital RF frontend. This paper is focused on the benefits of the second-order BPS architecture in spectrum sensing over a wide frequency band range and in multiband receiving without modification of the RF hardware. Methods to manipulate the spectra are described, and reconstruction filter designs are provided. On the basis of this concept, second-order BPS frontends for CR/SDR systems are designed and verified using a hardware platform.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.6
• /
• pp.527-538
• /
• 2002

In this study, the performance of sampling and of analytical methodology was examined against a number of selected volatile organic compounds (VOCs) in the ambient air. The canister-based sampling method for VOCs has been a viable and widely used approach that is based on research and evaluation performed over the past several years. VOCs were determined using canisters by GCMSD analysis. A total of target analyses in this study included approximately 30 VOCs designated in TO-l4A categories including BTEX. The methodology for QC(quality control) was intensively investigated with a wide range of performance criteria such as; (1) cleanliness of canisters, (2) reproducibility of diluter, (3) instrumental detection limits of preconcentrator and GCMSD, and (4) precision and accuracy of GCMSD. For most of the compounds tested, precision was less than $\pm$5%, IDL was 0.2 ppbv, accuracy was $\pm$5%, respectively. This study demonstrated that the combination of canister sampling and GC/MSD analysis could be reliably applied to the measurements of BTEX in ppbv levels that are typically observed in/outdoor air environment.

• Wind and Structures
• /
• v.18 no.6
• /
• pp.651-668
• /
• 2014

Wind tunnel tests are conducted to investigate the wind loads on vertical fixed-roof cylindrical tanks with a very low aspect ratio of 0.275, which is a typical ratio for practical tanks with a volume of $100,000m^3$. Both the flat-roof tank and the dome-roof tank are investigated in present study. The first four moments of the measured wind pressure, including the mean and normalized deviation pressure, kurtosis and skewness of the pressure signal, are obtained to study the feature of the wind loads. It is shown that the wind loads are closely related to the behavior of flow around the structure. For either tank, the mean wind pressures on the cylinder are positive on the windward area and negative on the sides and the wake area, and the mean wind pressures on the whole roof are negative. The roof configurations have no considerable influence on the mean pressure distributions of cylindrical wall in general. Highly non-Gaussian feature is found in either tank. Conditional sampling technique, envelope method, and the proper orthogonal decomposition (POD) analysis are employed to investigate the characteristics of wind loads on the cylinder in more detail. It is shown that the patterns of wind pressure obtained from conditional sampling are similar to the mean pressure patterns.An instantaneous pressure coefficient can present a wide range from the maximum value to the minimum value. The quasi-steady assumption is not valid for structures considered in this paper according to the POD analysis.

• Water for future
• /
• v.25 no.2
• /
• pp.89-97
• /
• 1992

This study is to verify the applicability of statistical models for predicting flood frequency at the stage gaging stations selected by considering whether the flow is natural condition in the Han River basin. From the result of verification, this statistical flood frequency models showed that is fairly reasonable to apply in practice, and also were compared with sampling variance to calibrate the statistical dfficiency of the estimate of the T year flood Q(T) by two different flood frequency models. As a result, it was showed that for return periods greater than about T=10 years the annual exceedence series estimate of Q(T) has smaller sampling variance than the annual maximum series estimate. It was showed that for the range of return periods the partial duration series estimate of Q(T) has smaller sampling varianed than the annual maximum series estimate only if the POT model contains at least 2N(N:record length)items or more in order to estimate Q(T) more efficiently than the ANNMAX model.

• Journal of Biomedical Engineering Research
• /
• v.10 no.1
• /
• pp.33-42
• /
• 1989

The doppler effect is used for measuring the velocity of the blood flow in artery. Because of the range information, the pulsed doppler system is most commonly used. In this paper, we propose a new two-dimensional(2-D) pulsed Doppler system. Which uses second-order sampling method and serial processing. The proposed system using second-order sampling method eliminates in-phase, quadrature-phase balancing problem at demodulator of quadrature detection method. In addition, the new pulsed 2-D doppler system eliminates balancing problem of channels of 2-D doppler system because of serial processing.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.2
• /
• pp.52-57
• /
• 2001

The passive ranging estimation techniques using a focused beamformer have been studied under the water. It is well known that the passive ranging estimation method using a focused beamformer is excellently evaluated. Among these, the passive ranging sonar is known to have a good performance under low signal-to-noise. ratio. However, its performance is degraded in multi-source environments. In this paper, we proposed the technique using dual focused beamformers to estimate the range. And when the sampling frequency is low, it is very difficult to steer the focused beam to the desired direction, as a result of this, the low performance occurs because of a distorted beam pattern. In this paper, we study the effect of sampling rate on passive ranging by using focused beamformer. And we verified the performance of the proposed method via computer simulation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.7
• /
• pp.1024-1031
• /
• 2012

In this paper, FMCW type radar level transmitter using correlation analysis method is implemented for precise distance measurement of cargo tank. FMCW type radar level transmitter is the device for distance measurement which calculates the distance by analyzing the beat frequency, that is, the frequency difference between Tx and RX signal from radar antenna using Fast Fourier Transform(FFT), but compensated algorithm like Zoom FFT is needed for the improvement of the frequency precision because the frequency precision of FFT is limited depending on sampling frequency and the number of sampling data. In case of Zoom FFT, the number of sampling data and noisy signal are the main factor influencing the measurement accuracy of Zoom FFT like FFT. Therefore, in order to overcome the limited environment and achieve the precise measurement, correlation coefficient is used for the distance measurement and the errors of measurement are verified to be in the range of ${\pm}1mm$.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.35 no.6
• /
• pp.527-534
• /
• 2017

The purpose of this study is to develop unmanned equipment that can automatically move to the desired point and measure water quality at the correct depth. For this purpose, we constructed a water sampling lift and water sampling container, an unmanned vessel equipped with a VRS-GPS, an acoustic echo sounder, and a water quality sensor. Also, we developed an automatic navigation algorithm and program, an automatic water sampling program, and a water quality map generation program. As a result of the experiment in the detention pond, the unmanned vessel sailed along the planned route with an accuracy of about 93% within the error range of 3m. In addition, the water quality sensor installed in the lift was able to acquire the water quality of the target area in real time and transmit it to the server via wireless Internet, and it was possible to monitor the water quality of each site in real time. Through field experiments, the water sampling lift was able to control the desired length with an accuracy of about 94%. The stretch length accuracy experiment of the water sampling lift was impossible to measure directly in the water, so it was replaced land-based experiment. We also found some unstable problems due to the weight of the water sampling lift and the weight of the air compressor to operate the water container. Except these two problems, we accomplished purpose of this study. An automated water quality measurement method using an unmanned vessel can be used to measure the quality of water in a difficult to access area and to secure the safety of the worker.