• Journal of the Korean Society of Clothing and Textiles
• /
• v.14 no.4 s.36
• /
• pp.292-304
• /
• 1990

The surface change of upperarm and shoulder blade area are caused by the extensive upper limb movement, thus it is necessary to measure the amount of change for constructing the clothing. Moire photography was taken after plastic casters of upperarm and shoulder blade area was prepared. 1. For the shoulder blade area, subjects showed the same change of surface area for the various limb positions, wherease, for the upperarm only at the $0^{\circ}\;and\;180^{\circ}$ limb position, same change was observed. 2. As the movement of the upperarm was increased, surface area of axillary part was increased and that of shoulder part was decreased. 3. To make a bodice pattern, the minimum size of the back with the ease were $\frac{B}{4}$+3.13 cm R for normal wear and $\frac{B}{4}$+5.75 cm for active wear. 4. As the movement of the arm was increased, the cross section for the upperarm were changed to elliptical shape. 5. For each horizontal basic line, there was a positive correlation between the amount of change of shoulder blad area and that of upperarm area.

• Journal of the Korean Society of Safety
• /
• v.20 no.3 s.71
• /
• pp.71-77
• /
• 2005

This study aims to find the safe vent area to prevent a destruction of building by gas explosion in a building. Explosion vessel which used in this experiment is 1/5 scale down model of simple livingroom and its dimension is 100cm in length 60cm in width and 45cm in height. Liquified petroleum gas(LPG) was injected to the vessel to the concentration of 4.5vol%, and injection rate were varied in 1L/min or 4L/min. Gas mixture was ignited by the 10kV electric spark. For analysis the characteristics of vented explosion pressure according to the vent size and vent shape, its size and shape were varied. From the experiment, it was found that explosion pressure in the vented explosion :in affected by the gas injection rate, vent area and vent shape. And the vent area to volume ratio(S/V) to prevent the building destruction by explosion pressure, it is recommended that the design of vent area happened by the explosion should be above 1/500cm in S/V. And if the vent area has complicate structure in same area, vented explosion pressure will be higher than a single vent, and possibility of building destruction will increase. Therefore to effectively vent the explosion pressure for protect a building and residents from the gas explosion hazards, the same vent area should have a singular and constant shape in the cross-sectional area of the vessel.

• The Korean Journal of Ecology
• /
• v.20 no.5
• /
• pp.339-345
• /
• 1997

The Arisaema robustum, perennial non-stem herb, population in the temperate forest of Sanseong-ri, Joongbu-myeon, Kyonggi Province was studied for leaf pattern and leaf growth from 1993 to 1995. The area of each side leaflet was larger than that of the apical leaflet in 3-leaflet form plants. But there was no significant difference among the leaflets (apical, 1st side and 2nd side leaflet) in t-testing of the 5-leaflet form plants. The specific leaf area (SLA) of the 3-leaflet form plant was greater than that of the 5-leaflet form plant, and the difference was significant at 0.1%. But differences of SLA value among the leafleats of the same leaflet form plants were minor. The area of leaflets or total leaf area was inversely proportioned to the their SLA values. Especially, the correlation coefficients (CC) between leaf area and SLA in apical leaflets and side leaflets of the 3-leaflet form plant compared to the 1st side leaflets of the 5-leaflet form plants were significant at the level of 1%. The differences between two sides in the dry weight and area of leaflets starting from the apical leaflets were about 5%. The CC values between attributes of the petiole (length and dry weight) and those of leaf blades (dry weight, leaf area and SLA) were high and significant at a 1% level. Especially, The CC value between the dry weight of the petioles and that of the leaf blades was higher than any others (r=0.952). The morphologies of the leaf margins were entire, medium serrate and serrate, and the same plant showed the same type from year to year. The plants usually had one leaf and occasionally 2 leaves. 1-leaf plants usually had 3 or 5 leaflets and occasionally 2 or 4 leaflets. Each year, the ration of individuals having the same number of leaflets was 72%, and that of individuals having a different number of leaflets was 27.54% (an increase of 20.4% and a decrease of 7.1% respectively). In the individuals increasing in the number of leaflets, the ration of individuals shifting from the 3-leaflet from to the 5-leaflet form was 14%. The increase ration of leaf area per individual a year was 37%, and the increase ratios of the plants increasing in leaflets were 60-70% regardiness of leaflet increase. The ratios of leaflet length/breadth were about 1-2, and the variations of those were 0.182-0.286 each year (12-20%).

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.82-89
• /
• 2004

To secure stability and availability of Rammed Aggregate Pier method as the foundation of a structure, the shear strength characteristics according to the area replacement ratio of RAP and the relative density of in-situ ground was studied through soil laboratory tests and large direct shear tests in a model ground. As a result, the internal friction angle tends to increase in proportion to in-situ relative density(Very Loose, Loose, Medium) in composite ground formed by the same area replacement ratio of RAP and also increase in proportion to increasing the area replacement ratio(30, 40, 50%) of RAP in the same ground condition. Furthermore, the comparative analysis between the experimental value and theoretical value of the shear strength is carried out.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2000.05a
• /
• pp.38-44
• /
• 2000

To determine the optimum sowing date and nursery period in Alisma piantago in the southern area of Korea, Alisma plantago local cultivar was grown under three different sowing dates and nursery periods. The plant height, leaf width and leaf length at the area sown on the seedbed in June 30 and conducted the growing seedling in 30 days is 12.1cm, 2.5cm and 3.1cm respectively and it shows tess decrease than that of plant height, leaf width and leaf length with 12.3cm, 2.6cm and 3.2cm respectively which was sown on the seedbed in June 20 and carried out the growing seedling in 30 days, and it also shows less decrease than that of plant height, leaf width and leaf length with 15.2cm, 3.1cm and 5.2cm respectively at the area sown on the seedbed in July 10 and condected the growing seedling in the same date. The stem length, number of stems and diameter of root at the area sown on the seedbed in June 30 and conducted the growing seedling in 30 days is 31cm, 11 and 3.7cm respectively and it shows more increase than that of stem length, number of stem and diameter of and on the other hand shows tess decrease than that of stem length, number of stems and diameter of root with 30cm, 10cm, 35cm respectively which was sown on the seedbed in 30 days, and on the other hand shows less decrease than that of stem length, number of stems and diameter of root with 32cm,13cm,3.9cm respectively at the area sown on the seedbed in July 10 and conducted the growing seedling in the same date, The fresh yield of roots at the area sown on the seedbed in June 30 and conducted the growing seedling in 30 days is 431.4Kg/10a and it shows more increase of 26.9Kg than that of fresh yield of root with 410.59g110a which was sown on the seedbed in lune 20an4 carried out the growing seedling in 30 days, and it also shows more increase of 7Kg than that of fresh yield of root with 430.4Kg/10a at the area sown on the seedbed in July 10 and conducted the growing seedling in the same date. The dry yield of roots at the area on the seedbed in June 30 and conducted the growing seedling in 30 days is 351.9Kg110a which was sown on the seedbed in June 20 and carried out the growing seedling in 30 days, and it also shows more increase of 16.4Kg than that of dry yield of root with 335.4Kg110a at the area sown on the seedbed in July 10 and conducted the growing seedling in the same date. Therefore, the seedling period of proper seedbed for high yield bumper crop of Alisma plantago for exporting to Japan is June 30 and the number of days for seedling is 30 days.

• The Journal of Advanced Prosthodontics
• /
• v.4 no.1
• /
• pp.7-12
• /
• 2012

PURPOSE. Articulation paper mark size is widely accepted as an indicator of forceful tooth contacts. However, mark size is indicative of contact location and surface area only, and does not quantify occlusal force. The purpose of this study is to determine if a relationship exists between the size of paper marks and the percentage of force applied to the same tooth. MATERIALS AND METHODS. Thirty dentate female subjects intercuspated into articulation paper strips to mark occlusal contacts on their maxillary posterior teeth, followed by taking photographs. Then each subject made a multi-bite digital occlusal force percentage recording. The surface area of the largest and darkest articulation paper mark (n = 240 marks) in each quadrant (n = 60 quadrants) was calculated in photographic pixels, and compared with the force percentage present on the same tooth. RESULTS. Regression analysis shows a bi-variant fit of force % on tooth (P<.05). The correlation coefficient between the mark area and the percentage of force indicated a low positive correlation. The coefficient of determination showed a low causative relationship between mark area and force ($r^2$ = 0.067). The largest paper mark in each quadrant was matched with the most forceful tooth in that same quadrant only 38.3% of time. Only 6 2/3% of mark surface area could be explained by applied occlusal force, while most of the mark area results from other factors unrelated to the applied occlusal force. CONCLUSION. The findings of this study indicate that size of articulation paper mark is an unreliable indicator of applied occlusal force, to guide treatment occlusal adjustments.

• The Korean Journal of Ecology
• /
• v.26 no.4
• /
• pp.173-180
• /
• 2003

To clarify whether the closely related species living in the same area is a population or populations ecologically, leaf morphology, specific leaf area, and fruit and seed production were studied in the natural group of sect. Pes-gallinaceua of Corydalis of Namhansansung area from 1999 to 2000. There were 352 plants in one square meter and total eight species or varieties were identified. Of the 352 plants, the number of C. turtschaninovii was the most with 103(29.3%), and that of C. ambigua was the next with 78(22.2%), and that of C. turtschaninovii var. fumariaefolia was the smallest with 9(2.6%). In the 28 plants having spotted leaves, central leaflet did not parted or again parted. The extent of partition with the plant was various from non-parted type to perfectly two-parted type (three leaflet). Between two extreme types, there were diverse types so that this character formed a gradient. The rate of length/breadth was in the range of 0.79~2.17. This character was related to the extent of leaflet partition but did not well expressed the distinguishing trait along a species. The number and the type of serration were diverse and there was no sharp borderline among the species or varieties. Ecological properties, specific leaf area, the number of fruit per plant, and the number of seed per fruit, varied with a wide range in a species or variety but differences between species or variety were not significant. Therefore, the Corydalis group studied was regarded as a population on the three criteria: (1) possibility of interbreeding, (2) continuity of leaf morphology, (3) irrelevance between character and species, (4) similarity of several ecological properties.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.3
• /
• pp.48-54
• /
• 2000

In this study the characteristics of chip formation of the cold drawn Bi-S free machining steels were assessed. And for comparison those of the cold drawn Pb-S free machining steel the hot rolled low carbon steel which has MnS as free machining inclusions and the conventional steels were also investigated. During chip formation the cold drawn free machining steels show relatively little change in thickness and width of chip compare to those of the conventional carbon steels. And a single parameter which indicates the degree of deformation during chip formation chip cross-section area ratio is introduced. The chip cross-section area ratio is defined as chip cross-section area is divided by undeformed chip cross-section area. The variational patters of the chip cross-section area ratio of the materials cut are similar to those of the shear strain values. The shear stress however seems to be dependent on the carbon content of the materials. The cold drawn Bi-S and Pb-S steels show nearly the same chip forming behaviors and the energy consumed during chip formation is almost same. A low carbon steel without free machining aids shows poor chip breakability due to its high ductility. By introducing a small amount of free machining inclusions such as MnS Bi, Pb or merely increasing carbon content the chip breakability improves significantly.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.351-356
• /
• 1999

In this study, the characteristics of chip formation of the cold drawn Bi-S free machining steels were assessed. And for comparison, those of the cold drawn Pb-S free machining steel, the hot rolled low carbon steel which has MnS as free machining inclusions and the conventional steels were also investigated. During chip formation, the cold drawn free machining steels show relatively little change in thickness and width of chip compare to those of the conventional carbon steels. And a single parameter which indicates the degree of deformation during chip formation, 'chip cross-section area ratio' is introduced. The chip cross-section area. The variational patterns of cross-section area is divided by undeformed chip cross-section area. The variational patterns of the chip cross-section area ratio of the materials cut are similar to those of the shear strain values. The shear stress, however, seems to be dependent on the carbon content of the materials. The cold drawn BiS and Pb-S steels show nearly the same chip forming behaviors and the energy consumed during chip formation is almost same. A low carbon steel without free machining aids shows poor chip breakability due to its high ductility. By introducing a small amount of non-metallic inclusions such as MnS, Bi, Pb or merely increasing carbon content the chip breakability improves significantly.

• Journal of Environmental Health Sciences
• /
• v.3 no.1
• /
• pp.22-26
• /
• 1976

Korea Parasite Eradication Association alleged in its seasonal spring report in 1975 that 36.8 percent of primary, middle and high school students in Seoul area are infected with parasites. Such a high rate of infection is a result of having used raw excrement for manure. Soil is, therefore, to a large extent infected with parasite eggs. In order to present helpful reference materials for preventing parasite infection in the area where human feces have been used for manure, soil in Seoul area and the suburban districts is sampled at random and then the rate of infection in various areas and the variation of infection rate in the same area are studied. The results are as follows 1) The parasite infection rates the according to districts are, Sootaik-ri 39.9%, Chamsil-dong14.2%, Songpa-dong 13.2%, Sageun-dong 12.8% Chayang-dong 11.4%, Sungsoo-dong 8.5%. The above figures show that the rate becomes higher as the area is farther from the urban and residential districts and nearer to the rural area. 2) The rates of detected parasites according to their kinds are as follows Ascaridae 55.9%, Ancylostomatidae 19.9%, Trichocephalus 13.5%, Trichostrongylus 5.7%, Tenia 3.9%, Enterobius 1.1% 3) The monthly variation of infection rate in the same districts, in the case of Sageun-dong, is, August 25.7%, July 18.9%, June 16.2%, September 15.3% April 12.6%, May 11.3%. The above shows that the infection rate of soil is comparatively higher in the summer season.