• 제목/요약/키워드: Safety shoes

검색결과 63건 처리시간 0.028초

클로로프렌의 유해성과 작업환경 관리 (Hazards of Chloroprene and the Workplace Management)

  • 김현영;임철홍
    • 한국가스학회지
    • /
    • 제19권3호
    • /
    • pp.1-8
    • /
    • 2015
  • 본 연구는 신발, 타이어, 접착제 제조에 많이 사용되는 클로로프렌(chloroprene)에 대해 취급근로자의 건강장해 예방을 위해 유해성을 조사하고, 취급사업장에 대해 작업환경을 측정 노출농도 및 용량반응을 통해 위험성을 평가하였다. 클로로프렌은 국제암연구소(IARC)로부터 발암추정물질(2B), 표적장기 전신독성 및 생식독성물질로 국내 취급 사업장은 27개소, 연간 약 1,300톤이 사용되었으며, 노출 위험성은 노출환경에 따라 Monte-carlo simulation을 이용하여 산출하였다. 그 결과 국소배기장치가 없으며 1일 4시간 초과 작업시 발암을 일으킬 수 있는 위험성의 평균값은 26,404로, 국소배기장치가 있으며 15분 미만의 단시간 작업 경우 2,199에 비교해 매우 높은 위험성을 보였다. 그리고 표적장기 전신독성의 경우도 169.06으로 단시간 작업 경우 4.10에 비교해 표적장기 전신독성 발생 위험이 높은 것으로 평가되어 물질의 노출시간 및 환기방식에 깊은 상관관계가 있는 것으로 나타났다. 따라서 클로로프렌 노출에 의한 근로자의 건강장해 예방하기 위해 국소배기장치의 가동과 방독마스크의 착용 등 노출저감을 위한 작업환경 관리의 필요성이 있었다. 특히 클로로프렌은 발암성, 생식독성 물질로 미국 산업안전보건청(OSHA)에서는 TWA를 5 ppm($18mg/m^3$) 이하로 관리하고 있으며, 본 유해성조사 결과에서도 현행 노출기준 10 ppm이하에서 표적장기독성, 생식기 장해 등 생체에 미치는 영향이 있는 것으로 나타나 있어, 위험성이 강하게 예측되므로 현재 사용하고 있는 우리나라 작업환경 노출기준(TWA 10 ppm)도 5 ppm 수준으로 강화하여 근로자 건강장해 예방에 기여할 필요성이 있는 것으로 판단되었다.

발포 및 세척 공정 근로자의 공기중 Methylene Chloride 노출 농도와 혈중 Carboxyhemoglobin 수준간의 상관관계에 관한 연구 (Relationship between Exposure Concentrations to Methylene Chloride in Air and Carboxyhemoglobin Levels in Blood of Workers Engaged in Blowing, and Cleaning Operations)

  • 신용철;김양호;이광용
    • 한국산업보건학회지
    • /
    • 제9권1호
    • /
    • pp.87-98
    • /
    • 1999
  • The objectives of this study were to evaluate exposures to airborne methylene chloride and postshift carboxyhemoglobin (COHb) in blood of workers engaged in processes using blowing or cleaning agents, and to investigate correlation between methylene chloride concentrations and the blood COHb levels of workers. The geometric mean (GM) of workers' exposures (8 hour-time weighted averages, TWA) to airborne methylene chloride during cleaning molds using rags wetted with the solvent in the manufacture of flexible polyurethane foam (GM = 61.4 ppm), during operating the dip tank for cleaning molds in the manufacture of lens (GM = 61.0 ppm), and during cleaning the blowing nozzles by spraying the solvent in the manufacture of shoes (GM = 117.2 ppm) were exceeded the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value ($TLV^{(R)}$)-Time Weighted Average (TWA) (50 ppm). The COHb levels were significantly different among groups (p<0.05). The average COHh levels in blood of non-smoking workers were 2.0% in. low-level (<50 ppm) exposure group, and 3.9 % in high-level (>50ppm) exposure group. The average COHb levels in smoking workers were 3.1% in low-level exposure group, and 4.8% in high-level exposure group. The blood COHb levels of no-exposed workers to methylene chloride were 1.8% in non-smoking group, and 2.8% in smoking group. It was found that the COHb level dependeds on the methylene chloride concentration and smoking habit, and was highly correlated with methylene chloride concentration in air. The correlation coefficient was 0.81 among non-smoking workers. The estimated COHb level (3.6%) and 95% upper confidence limit (4.0%) corresponding to TLV-TWA of methylene chloride exceeded the current ACGIH Biological Exposure Index (COHb 3.5%) for carbon monoxide. The estimated COHb level (5.4%) at 100 ppm exceeded the standard (5%) recommended by National Institute for Occupational Safety and Health (NIOSH) for preventing adverse cardiovascular effect. The estimated COHb value and 95% upper confidence limit at 25 ppm of the Occupational Safety and Health. Adminstration (OSHA) Permissible Exposure Limit-TWA (PEL-TWA) were 2.6% and 3.0%, respectively. It is suggested that COHb in blood be kept below 3.0% to comply with OSHA PEL-TWA.

  • PDF

데크의 논슬립가공 표면형태 변이에 따른 마찰성능 변화 평가 (Evaluation of friction force varied by non-slip surface patterns of deck)

  • 한연중;이주희;박용건;최윤호;여환명
    • Journal of the Korean Wood Science and Technology
    • /
    • 제40권6호
    • /
    • pp.397-405
    • /
    • 2012
  • 최근 국내에서 목질계 재료를 이용한 데크의 설치사례는 증가하는 추세이나, 상대적으로 데크의 기초 물성과 안전성에 관련된 연구는 미흡한 상황이다. 신발과 데크 사이에서 발생하는 마찰력은 보행자의 기동 능력에 많은 영향을 미친다. 이러한 마찰력은 바닥재의 재료 특성, 바닥재의 요철무늬 형상, 신발 밑창의 형태, 바닥재와 신발 사이 접촉면의 습윤도 등 여러 인자에 의해 영향을 받는다. 본 연구에서는 보행안전성 평가를 위하여 데크의 요철무늬에 따른 마찰력 변화를 측정하고 미끄럼 정도를 평가하였다. 실험에 이용된 데크의 재료는 천연목재와 합성목재의 두 종류이고, 신발과 접촉하는 데크표면은 데크의 길이 방향으로 홈가공처리를 한 단일 논슬립가공 형태와 길이방향에 더불어 가로방향에 추가로 홈 가공처리를 한 이중 논슬립가공 형태 두 종류이다. 실험에 사용된 신발의 밑창 형태는 더블유형(W형)과 네모형(${\Box}$형)의 두 종류를 사용하였고, 데크 표면의 함수율 상태에 따른 마찰력변화를 알아보기 위하여 대기와 평형을 이룬 건조상태와 수분습윤상태에서 측정하였다. 각각의 조건에서 마찰계수를 결정하고 각각의 인자가 마찰력에 미치는 영향을 분석하였다.

위치추적기를 내장한 산악용 신발 디자인 및 3D 다공성 폴리머 프린팅을 이용한 중창 제작에 관한 연구 (A Study on the Design of Hiking Boots Equipped with GPS and its Midsole Manufactured by 3D Porous Polymer Printing Method)

  • 표정희;유찬주;송영민;이태구;신보성
    • 한국기계가공학회지
    • /
    • 제15권6호
    • /
    • pp.83-88
    • /
    • 2016
  • Over the last five years, 568 people have died while hiking according to 2015 statistics from the public safety ministry. Among those deaths, approximately 33% were due to loss of footing or falling. In this respect, the highly advanced functions of hiking boots should be considered to prevent these unfortunate accidents. For example, by utilizing the Internet of Things (IoT) and Information and Communications Technology (ICT), hiking boots equipped with a Global Positioning System (GPS) or vital signs monitoring systems should be considered. In addition, many challenges remain for the production of 3D printed hiking boots, because the functions of hiking boots are variable, which is important when handling changing terrains and situations. The design of customized hiking boots was introduced in this paper, and 3D printing applications for midsoles using a Porous Polymer Printing (PPP) method was also suggested to verify the possibility of manufacturing hiking boots.

스마트패션제품 개발 동향에 관한 연구 (A study on smart fashion product development trends)

  • 서성은;노정심
    • 복식문화연구
    • /
    • 제23권6호
    • /
    • pp.1097-1115
    • /
    • 2015
  • ICT in the IOT era is the core basis of modern society. This study investigated and analyzed the recent commercialization trends of smart fashion products internationally and domestically, to utilize them as the basis of data for developing user-friendly smart fashion products that can meet the needs of consumers. Keyword research using the most representative search engines, Google and Naver was conducted for searching for various wearable items commercialized actively since 2010. The final 78 products were classified by the physical area, and the key features and benefits were analyzed. Smart fashion products were classified as four physical types for the head and face, torso, arms and hands, and ankles and feet. Smart fashion products for each body part were developed in various ways, such as hats, glasses, lenses, virtual screens, earphones, headsets, clothing, watches, wrist bands, gloves, rings, wallets, bags, anklets, shoes, socks, and insoles. The main features were music playback, bluetooth, a camera based on NFC, virtual effects, health and safety protection through measuring heartbeat and momentum, and social network sharing of all kinds of information, based on inter-working with a smartphone. These functions represent the physical, social, and emotional interactions among users and their surroundings, as well as the users, themselves. The research results are expected to be used in future studies on planning user-friendly and marketable products through in-depth analysis of the design characteristics of smart fashion products as well as consumer responses.

3D 프린팅 Auxetic Re-entrant 패턴의 기울기 각도에 따른 네오프렌 복합 직물의 역학적 특성에 관한 연구 (Mechanical Properties of 3D Printed Re-entrant Pattern/Neoprene Composite Textile by Pattern Tilting Angle of Pattern)

  • 김혜림;카비르 샤흐바지;이선희
    • 한국의류학회지
    • /
    • 제45권1호
    • /
    • pp.106-122
    • /
    • 2021
  • This study confirmed the mechanical properties of an auxetic re-entrant pattern prepared using 3D printing technology and its composite fabric with neoprene for the production of functional auxetic patterns/textiles for safety shoes. Samples were prepared by the tilt angle of a re-entrant pattern of 0°, 30°, 45°, 60° and 90°, and then analyzed using Poisson's ratio, bending, compression, and tensile properties. A 3D printed auxetic re-entrant pattern (3DP-RE) and its composite fabric (3DP-RE/NP) showed a negative Poisson's ratio in all tilting angles that indicated auxetic properties. The results of the bending property shown that strength of 3DP-RE/NP was 1.5 times lower than NP, but the strain improved 2.0 times. It was confirmed that the deformation of 3DP-RE/NP is possible with a low load. Each sample type of compression behavior indicated similar regardless of the tilting angles; in addition, the compression toughness of 3DP-RE/NP increased 1.2 times compared with NP. In the case of tensile properties, 3DP-RE and 3DP-RE/NP were affected by the tilting angle, samples with 90° (the opposite of load direction) showed best tensile property and toughness. 3DP-RE/NP indicated improved bending, compression, and tensile properties.

전북지역 산업체급식소 조리종사자의 고용형태에 따른 안전사고 실태 및 안전사고 예방관리에 대한 중요도와 수행도 분석 (Comparative analysis of status of safety accidents and importance-performance analysis (IPA) about precautions of safety accidents by employment type of industry foodservices in Jeonbuk area)

  • 소희;노정옥
    • Journal of Nutrition and Health
    • /
    • 제50권4호
    • /
    • pp.402-414
    • /
    • 2017
  • 본 연구는 전북지역 산업체급식소의 정규직과 비정규직 조리종사자 282명을 대상으로 급식소에서의 안전사고, 안전교육 실태 및 안전사고 예방관리의 중요도 및 수행도를 조사하여 산업체급식소의 안전사고 예방을 위한 효율적인 관리방안을 제시하고자 하였으며, 그 결과를 요약하면 다음과 같다. 조사대상자는 정규직 42.2% (119명), 비정규직 57.8% (163명) 이며 96.5%는 여자이었다. 고용형태에 따라서는 연봉수준 (p < 0.001), 직급 (p < 0.001), 평균 연령 (p < 0.001), 급식횟수 (p < 0.001)에서 유의적인 차이를 보였다. 정규직의 66.4%, 비정규직의 53.4%가 안전사고의 경험이 있으며 (p < 0.05), 사고원인은 본인의 부주의 (53.5%)가 가장 큰 원인이었다. 사고처리는 정규직은 회사부담 (71.6%)이 높으며 비정규직은 산재처리 (44.6%)가 높았다. 안전사고는 정규직은 화상 (48.6%), 절단사고 (31.1%)가 높았으며 비정규직은 미끄러짐 (47.8%)과 화상 (44.6%)의 순으로 차이가 있었다. 사고부위는 주로 손과 팔 (63.3%) 이었다. 정규직의 98.3%, 비정규직의 95.1%가 안전사고 예방을 위한 안전교육을 받았으며, 교육은 주로 영양사 (93.4%)가 실시하나 정규직은 산업안전관리공단 (6.8%)과 협회(2.6%)의 교육도 받고 있었다. 교육 빈도는 정규직의 68.4%가 1회, 23.9%가 2회, 7.7%는 3회 이상의 교육을 받았으나 비정규직은 1회 50.3%, 2회 37.4%, 3회 이상 12,2%로 비정규직의 교육 빈도가 유의하게 높았다 (p < 0.05). 교육방법은 주로 강의 (77.2%)로 진행되며, 교육 후 정규직의 37.6%는 별도의 평가가 없으나, 비정규직의 33.5%는 시험, 25.2%는 면담, 12.3%는 실기평가를 실시하고 있었다 (p < 0.05). 교육만족도는 조사대상자의 81.6%가 만족하며 비정규직 (85.2%)이 정규직 (76.9%)보다 더 만족하는 경향을 보였다. 교육 후 정규직의 73.5%, 비정규직의 71.6%만이 실제 작업에 교육내용을 적용하고 있었다. 적용하지 못하는 이유는 업무과중으로 인한 시간부족과 습관적인 작업행태 때문이었다. 산업체급식소의 정규직과 비정규직 조리종사원의 안전사고 예방관리에 대한 정규직과 비정규직의 중요도는 각각 4.26점, 4.15점이며 수행도는 정규직 3.96점, 비정규직 3.94점이었다. 독립표본 t-test로 분석한 결과, 21개의 항목 중 '튀김요리 시 물이 튀지 않게 하며 화상에 주의한다'에서 정규직 (4.43점)이 비정규직 (4.24점)보다 중요도가 유의적으로 높았으나 (p < 0.05), 수행도는 모든 항목에서 정규직과 비정규직간 유의적인 차이는 없었다. 대응표본 t-test 분석결과, 정규직의 중요도와 수행도간의 유의적인 차이를 보였다 (p < 0.001). 전체 21개 항목의 중요도와 수행도간에 유의적인 차이를 보였다. IPA분석결과, 중요도와 수행도가 높은 A영역 (Doing great)에서 '작업장 바닥의 물, 기름을 청소', '작업장과 통로의 물건 정리', '작업 시 미끄럼방지 안전화 착용', '사용하지 않는 호스는 감아서 정리', '화재위험 있는 전열기 코드 뽑기', '튀김요리 시 화상에 주의하며 조리'는 정규직과 비정규직 모두 해당되었으며, 이외 '물기 있는 손으로 전기시설 관리하지 않기'는 정규직에만 해당되었으며 '야채절단기 사용 시전용방망이 사용', '안전하게 칼 관리'는 비정규직에만 포함되었다. 중요도가 높으나 수행도가 낮은 B영역 (Focus here)에서 '출근 후 환기와 가스누출 확인', '콘센트 안전관리'는 정규직과 비정규직 모두 해당되었으며 이외에 '영양사에게 건강상태 보고' 및 '중량물 취급 시 올바른 자세로 작업'은 정규직에만 '가스차단기 작동확인'은 비정규직에만 포함되었다. 중요도는 낮으나 수행도가 높은 C영역(Overdone)에서 '기계설비 잠금장치 확인'은 정규직과 비정규직 모두에 해당되었으며 이외에 '야채절단기 사용 시 전용방망이 사용', '안전하게 칼 관리'는 정규직에 포함되었으며 '물기 있는 손으로 전기시설 관리하지 않기', '전기기구 연결 확인', '영양사에게 건강상태 보고' 및 '중량물 취급 시 올바른 자세로 작업'은 비정규직에 포함되었다. 중요도와 수행도가 낮은 D영역 (Low priority)에 'MSDS관리', '화학물질 위험표시 인지', '화학물질 취급 전 보호 장갑 등의 장비 착용', '작업 전 스트레칭 실시' 및 '보조도구를 이용하여 안전하게 작업대 높이 조정'이 정규직과 비정규직에 포함되었으며 이외에 정규직에 '전기기구 연결 확인', '가스차단기 작동확인'이 추가되었다. 본 연구결과를 종합하면, 전북지역 산업체급식소에서의 안전교육 실시는 잘 진행되고 있으나 아직도 교육을 받지 못하는 비정규직이 있으므로 이에 대한 경영주 및 영양사의 인식전환이 필요하겠다. 또한 조리종사원들의 안전사고 예방관리에 대한 중요도 인식은 고용형태 간 유의적인 차이 없이 높은 수준이었으나 교육 후 업무과중의 이유로 실제 적용하는 어려움이 있는 점을 볼 때 효율적인 업무관리 및 안전사고 예방을 위한 철저한 감독이 요구된다. 특히, 화학물질에 대한 이해 및 MSDS관리에 대한 조리종사원들의 낮은 중요도 인식과 수행도는 향후 안전교육에서 중요하게 다루어야 하겠다. 향후 정규직과 비정규직 구분에 따른 지원의 차이를 줄이고 소속감을 높여 조리종사원의 책임감과 안전의식을 높여 보다 안전한 급식소환경이 될 수 있는 방안이 요구된다.

종합병원 급식소의 HACCP 선행요건 관리 수행도 평가 (Evaluation on HACCP prerequisite-program performance within general hospital foodservice operations)

  • 송윤지;배현주
    • Journal of Nutrition and Health
    • /
    • 제49권1호
    • /
    • pp.43-50
    • /
    • 2016
  • 병원급식소의 HACCP 선행요건 수행 실태를 분석하여 병원급식소 특성을 고려한 선행요건관리 개선 방안을 마련하고자 종합병원 규모의 병원 급식소 총 65곳의 급식관리자를 대상으로 설문조사를 실시한 결과, 선행요건 7개 관리영역 중 영업장관리 영역의 수행도는 선행요건 평가판정그룹별로 유의적인 차이가 있었으며, 적합 그룹 (85점 이상)에서 유의적으로 가장 높았다 (p < 0.001). 위생관리 (p < 0.001), 제조 가공 조리 시설 설비관리 (p < 0.001), 용수관리 (p < 0.001), 보관 운송관리 (p < 0.05) 영역의 수행도는 '부적합' 그룹 (70점 미만)이 '적합'이나 '보완' 그룹 (71점 이상 84점 이하)에 비해 유의적으로 낮았다. 조사대상 병원급식소와 영양사의 일반 특성에 따른 선행요건관리 평가 결과에 대한 차이 분석 결과 서울 경인지역이 대구 경북지역에 비해 선행요건 관리가 '적합'으로 평가된 비율이 유의적으로 높았다 (p < 0.01). 또한 선행요건 판정 그룹에 따른 급식시설 구비율은 '적합' 그룹이 '부적합' 그룹에 비해 3조 싱크 (p < 0.01), 대용량 오븐 (p < 0.01), 대형 에어컨 (p < 0.01), 보온고 (p < 0.01), 보냉고 (p < 0.05), 해동전용 냉장고 (p < 0.05), 위생장화 소독고 (p < 0.05) 등 총 7개 항목의 구비율이 유의적으로 높았다. 병원 급식품질 개선을 위해 HACCP을 빠른 시일 내에 효과적으로 적용하기 위해서는 선행요건 관리 항목이 준수되어야 하며, 이에 앞서 병원 급식소의 운영 특성을 고려한 선행요건관리 기준과 HACCP 관리 계획의 수립이 필요하다고 판단된다.

폐폴리올레핀 폼과 탄성 포장재로 구성된 어린이 놀이터 바닥의 안전성에 관한 실험적 연구 (Study on the Safety of Playground Flooring Made of Polyolefin Foam Waste and Rubber Paving)

  • 최수경;전명훈;이도헌
    • 한국건설순환자원학회논문집
    • /
    • 제1권3호
    • /
    • pp.246-254
    • /
    • 2013
  • 본 연구에서는 폐폴리올레핀 폼을 완충재로 이용한 어린이 놀이터 바닥의 안전성을 알아보기 위하여 한계하강높이, 보행적합성 및 장기피로예측, 미끄럼저항성에 대하여 시험하고 평가하였다. 시험체는 두께 30mm, 50mm, 70mm의 폐폴리올레핀 폼에 각각 탄성 포장재를 12mm, 15mm 두께로 포설한 6종류로 하였다. 한계하강높이 시험은 KS G 5758:2009에 의거하여 실시하였다. 보행적합성 및 장기피로예측 시험에는 바닥 경도 시험장치(O-Y HMA)를 이용하였으며, 미끄럼저항성 시험에는 휴대형 미끄럼 시험기(ONO PPSM)을 이용하였다. 시험결과, 폐폴리올레핀 폼과 탄성 포장재로 구성된 바닥은 충격저감성 관점에서 상당히 안전한 것으로 나타났다. 바닥의 경도는 남성에게는 보행감이나 피로 측면에서 우수한 성능을 발휘하지만, 여성에게는 구두(미들 힐)를 신고 보행하기에 적합하지 않고 오래 사용할 경우 쉽게 피로감을 느낄 수 있는 것으로 나타났다. 미끄럼저항성은 표면에 물기 등의 이물질이 있더라도 일상적인 동작에 대해서는 비교적 안전한 것으로 나타났다.

50인 미만 소규모사업장의 보건관리 실태 (Current State of Occupational Health in Small-Scale-Enterprises of Korea)

  • 윤순녕;김영임;정혜선;김순례;유경혜;송영숙;김화중
    • 지역사회간호학회지
    • /
    • 제11권1호
    • /
    • pp.90-104
    • /
    • 2000
  • This study was carried out to investigate the current state of occupational health management and characteristics of employees working in small-scale-enterprises (SSE) employing less than 50 workers. Samples were chosen among the two thousands employees working in 838 factories where located in Youngdungpo-Ku, Seoul, Korea. The study results were as followed: 1. Most factories investigated in the study were manufactures (68.6%) which were established in 5 to 10 years ago (29.2%), employing less than 5 workers (72.9%) and registered in accident compensation insurance (23.0%). 2. Health screening was undertaken in 24.9% workplaces for periodic health examination and in 1.5% for special health examination. Environmental monitoring was done in 3.3% factories. Very few factories displayed Material Substance Data Sheet (MSDS) in 3.1% among the total factories. 3. Workplaces usually had their own toilets in 75.9% and washing basin in 58.6% as types of sociowelfare facilities. 4. Employees responded in the study were mostly in the range of age from 30 to 39 in 34.7%. male in 84.8%. the married in 70.3%. manual workers in 42.0%. mostly working regularly 51 hours per a week in 48.2% and earned 710.000 Won to 1.000.000 Won per month in 35.0%. Medical utilization for employees were covered by factories sponsored medical insurance in 12.7% and by provincial sponsored medical insurance in 83.4%. 5. Two point six percents of employees were suffered by diseases. The health complaints indicated were mainly digestive problems in 46.7% and hypertension in 24.4%. 6. Employees wore personal protective equipments for work such as gloves in 48.1%. safety shoes in 30.5%. ear plug in 5.5% and mask in 6.9%. Based on the results of study, we recommend that various types of occupational health management should be developed according to workplace working condition of each factory. In addition to the development of occupational health strategies. we think that it is more important to monitor and to allocate how effectively they operate each other on the basis of longitudinal continuity. Besides, we would like to insist that these all management effort should be focused on prevention of disease and occupational health education of employees.

  • PDF