• Journal of the Korean Society of Radiology
• /
• v.14 no.4
• /
• pp.425-431
• /
• 2020

When a radiation generating device is installed in an export container due to COVID-19, the purpose of this study was to measure the space dose in the radiation room and to study the effectiveness of the shielding wall in the laboratory. Air dose measurement method was set behind the X-ray tube, 50 cm, 100 cm, 200 cm, and measured 12 locations. The dose values before and after the use of the movable radiation shielding wall were compared by measuring 3 locations behind the X-ray tube using the movable radiation shielding wall. The measured values were 50 cm on the left behind the X-ray tube: 1.446 μSv, behind the X-ray tube: 0.545 μSv, and 50 cm on the right behind the X-ray tube: 1.466 μSv. Measurements behind the radiation barrier were 0.190 μSv, 0.204 μSv, and 0.191 μSv. As a result of performing the corresponding sample t test of the average value according to the use of movable barrier walls, p <0.001 was found. As a result of the actual measurement, the medical exposure of the examiner due to the shielding wall in the laboratory decreased to 82.3%. In order to reduce occupational exposure in screening radiological laboratories, it is recommended that sufficient separation from radiation sources and the use of shielding walls are recommended.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.131-131
• /
• 2009

최근 환경규제가 강화되면서 친환경적인 전력생산 요구 등의 외부환경 변화에 따른 우리나라의 전력구조가 기존의 중압 집중형 발전을 탈피한 분산전원 발전에 대한 관심이 증대되고 있는 실정이다. 특히, 분산전원으로서의 전력생산은 공급의 안전성, 경쟁력 및 에너지의 지속성 등이 요구되어지는데, 재생에너지가 가지고 있는 에너지 지속성의 한계 및 설치의 제약성을 탈피할 수 있는 시스템으로 현재 연료전지시스템이 가장 근접해 있는 실정이다. 즉, 도시가스 인프라가 우수하고 인구조밀 지역이 많은 우리나라의 특성상 각 가정 및 건물에 쉽게 설치하고 공급의 안전성을 갖는 건물용 연료전지는 최근 가장 각광받고 있는 분산전원 시스템 중의 하나이다. 올해부터 모니터링사업의 일환으로 수용가에 설치 될 연료전지 시스템이 얼마나 안정적으로 전기와 열을 각 가정에 공급하고 시스템의 안전성을 확보하는 가는 건물용 연료전지의 분산전원으로서의 가능성 및 국민의 수용성을 증대시키는 중요한 역할을 할 것이다. 연료전지시스템은 상용전력과 연계되어 있기 때문에 시스템의 안정성 뿐만 아니라 상용전력의 변화에 대응하여 안정적인 운전을 하는지에 대한 평가가 필수적이다. 이에 따라 본 연구에서는 가정용 연료전지시스템의 성능 및 안전성평가의 일환으로 계통연계형 전력변환장치의 성능 및 안전성을 평가 하고자 한다. 연료전지 검사를 위한 계통연계형 전력변환장치의 시험평가 항목으로는 크게 정상특성성능시험, 보호기능성능시험, 과도응답특성성능시험 및 외부사고성능시험 등으로 나뉘어진다. 본 연구에서는 외부사고 성능시험 항목들인 출력측 단락시험, 계통전압 순간정전?순간강하시험 및 부하차단 시험 등을 통하여 외부사고에 대한 성능 및 안전성을 평가하였다. 외부사고 성능시험의 주 목적은 시스템의 이상 운전이 아니라 외부의 영향에 따른 시스템의 안전성 및 전력품질을 평가한다. 출력측 단락시험을 수행하기 위해서 전력변환장치를 정격 출력 전압, 정격 출력 주파수 및 정격 출력에서 운전한 후, 교류 전원장치는 단락 전류를 검출하여, 사고 발생 후 0.3초 이내에 개방하도록 설정하였다. 여기서, 단락 저항 Rsc를 정격 전류의 10배 이상에 해당하는 부하와 같은 값으로 설정하였다. 스위치 SWSC를 폐로하여 단락 상태를 만들며, 이 때 전력변환장치의 출력전류와 차단 또는 정지 시간을 측정하였다. 실험 결과에 대한 판정기준은 단락전류를 검출하여 0.5초 이내에 개폐기 개방 또는 게이트 블록 기능이 동작하여 시스템을 안정하게 정지시키고 시스템 어떤 부위에도 손상이 없어야 한다. 실험 결과 파워컨디셔너의 출력전류 및 차단 또는 정지된시간이 40ms로 나타났고, 출력전류의 파형도 매우 안정함을 볼 수 있었다. 이와 같이 모든 실험을 수행한 결과 외부사고에 대하여 시스템이 안전하게 정지하는 등 연료전지 시스템의 안전성을 확인하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.443-450
• /
• 2016

In this study, we propose a novel fiber optic sensor to show the measurement feasibility of distributed temperature and strains in a single sensing fiber line. Distributed temperature can be measured using optical time domain reflectometry (OTDR) with a Raman anti-Stokes light in the sensing fiber line. Moreover, the strain can be measured by fiber Bragg gratings (FBGs) in the same sensing fiber line. The anti-Stokes Raman back-scattering lights from both ends of the sensing fiber, which consists of a 4 km single mode optical fiber, are acquired and inserted into a newly formulated equation to calculate the temperature. Furthermore, the center wavelengths from the FBGs in the sensing fiber are detected by an optical spectrum analyzer; these are converted to strain values. The initial wavelengths of the FBGs are selected to avoid a cross-talk with the wavelength of the Raman pulsed pump light. Wavelength shifts from a tension test were found to be 0.1 nm, 0.17 nm, 0.29 nm, and 0.00 nm, with corresponding strain values of $85.76{\mu}{\epsilon}$, $145.55{\mu}{\epsilon}$, $247.86{\mu}{\epsilon}$, and $0.00{\mu}{\epsilon}$, respectively. In addition, a 50 m portion of the sensing fiber from $30^{\circ}C$ to $70^{\circ}C$ at $10^{\circ}C$ intervals was used to measure the distributed temperature. In all tests, the temperature measurement accuracy of the proposed sensor was less than $0.50^{\circ}C$.

• Korean Journal of Food Science and Technology
• /
• v.31 no.3
• /
• pp.788-793
• /
• 1999

In this study, it was investigated that the isolation and identification of spoilage bacteria from contaminated aseptic packaged cooked rice, the potential for application of acidic electrolyzed saline solution (AESS) as water-for-cooked rice and the microbiological safety of AESS-based cooked rice. Five strains of Bacillus subtilis and a B. cereus strain among the total six isolates were partially identified by biochemical method and by Microbial Identification System (MIS). The bactericidal effect of AESS was similar as 0.1% NaOCl and 70% ethanol solution, or better than that. All of the test microorganisms except Bacillus spp. that were exposed to AESS for five seconds were destructed. The effect of AESS against Bacillus spp. was much better than that of the two solutions and all of them were destructed or inhibited on exposure for five minutes. The pH value of cooked rice prepared using AESS was in the range of 3.6 to 4.3 and was not almost changed through the storage period. Various concentrations of cell suspension of Bacillus isolates were inoculated to cooked rice, which were prepared with tap water and AESS, and stored at $37^{\circ}C$ for two weeks. The result was shown that the bacteria in tap water-based cooked rice appeared normal cell growth, while they were completely repressed in AESS-based cooked rice.

• Food Science of Animal Resources
• /
• v.31 no.1
• /
• pp.47-53
• /
• 2011

Salmonella enterica serovar Typhimurium (ST) is one of the most common serovars isolated from humans and animals. It has been suggested that ST infections in Koreans are largely due to the consumption of contaminated pork and beef. To investigate the genotypes, phage types, and antimicrobial resistance patterns for ST isolates of different origins, a total of 70 ST strains, including 19 isolates from humans, 44 isolates from pigs, and 6 isolates from cattle, were analyzed using pulsedfield gel electrophoresis (PFGE), phage typing, and antimicrobial susceptibility tests. Forty-three distinct PFGE patterns were generated from 70 ST isolates, which were grouped into 14 PFGE groups (from A to N) at the level of 75% similarity. The most prevalent group was the A (A1-A17 subtypes) group, encompassing 54.5% (38/70) of ST isolates. ST isolates from pigs and cattle mostly belong to groups A and L, whereas ST isolates from humans mostly belong to groups F and C. Antimicrobial susceptibility tests using 11 antimicrobial agents showed that resistance to tetracycline (TE) (81.4%) was highly prevalent, followed by streptomycin (S) (64.3%) and nalidixic acid (NA) (31.4%) resistance. A total of seventeen antimicrobial resistance patterns were observed. Only 8.6% of isolates, including a reference strain, were susceptible to all antimicrobial agents tested. The most prevalent resistance pattern was TE-S (37.1%), which was seen in 66.6% of bovine, 40.8% of swine and 21.1% of human isolates. Three ST isolates from humans (15.9%) showed resistance to 7-8 antimicrobials. The most predominant phage type (PT) was U302 (64.3%), followed by DT170 (10.0%). PFGE types did not coincide with antimicrobial resistance patterns and phage types; therefore, the combination of those types allowed for further differentiation between tested ST isolates.

• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.1-5
• /
• 2015

In this study, the combustion characteristics of Hinoki Cypress Louver were measured after performing pressure impregnation with aqueous solution of boric acid, borax, and ammonium phosphate. The characteristics measured include ignition time, critical heat flux, and mass loss rate by incident hear flux (25, 30 and $50kW/m^2$). The samples used for the test were $100{\times}100{\times}10mm$, and the 5 min variation for each incident heat flux was measured 3 times. The results show that the ignition time for incident heat flux of $25kW/m^2$ showed a delay effect of 17.4 to 21.3% except for Type C-H. There was no significant difference at 35 and $50kW/m^2$ in the average mass loss rate in Types A-H and D-H, which had lower rates than Type N-H, which was predicted to be higher than that of Type N-H ($10.7kW/m^2$) by 38.22 to 60.46%. It is thus expected that at the time of initial primary fire, there would be a delay effect against fire spread.

• International Journal of Highway Engineering
• /
• v.5 no.1 s.15
• /
• pp.11-18
• /
• 2003

Road roughness, as the key factor influencing not only drivers' ride quality and safety but also pavement deterioration, is one of the most important pavement performance indicator to be evaluated by users' subjective assessment. For this reason, a specific number of the pavement roughness has been adopted to monitor the condition of a road for pavement management systems and to evaluate the quality of newly constructed sections, however, none of the unified methodology was internationally accepted. In Korea highway network, road roughness has been used mainly to evaluate newly placed pavement by using 7.6m CP (California Profile meter) to calculate PrI (Profile Index). But this instrument is manually operated to measure road profiles by traffic closure and their interpretation depends on personal bias. Therefore, problems arisen from the manually operated instrument will be overcome by using the APL (Longitudinal Profile Analyzer) which can be operated in the speed of 80km per hour. A study was conducted to correlate the relation from both concrete and asphalt pavement between IRI (measured by APL) and PrI (measured by 7.6m CP). Test results showed that there was a good correlation between IRI and PrI.

• Journal of the Korean Society of Radiology
• /
• v.10 no.7
• /
• pp.521-529
• /
• 2016

Since Gamma Knife(R) radiosurgery(GKRS) is based on a single-fraction high dose treatment strategy, independent verification for the results of Leksell GammaPlan(R) (LGP) is an important procedure in assuring patient safety and minimizing the risk of treatment errors. Several verification methods have been developed and reported previously. Thus these methods were tested statistically and tried on Leksell Gamma Knife(LGK) target treatments through the embodiment of the previously proposed algorithms(PPA). The purpose of this study was to apply and evaluate the accuracy of verification methods for LGK target treatments using PPA. In the study 10 patients with intracranial lesion treated by GKRS were included. We compared the data from PPA and LGP in terms of maximum dose, arbitrary point dose, and treatment time at the isocenter locations. All data were analyzed by Paired t-test, which is statistical method used to compare two different measurement techniques. No statistical significance in maximal dose at 10 cases was observed between PPA and LGP. Differences in average maximal dose ranged from -0.53 Gy to 3.71 Gy. The arbitrary point dose calculated by PPA and LGP was not statistically significant too. But we found out the statistical difference with p=0.021 between TMR and LGP for treatment time at the isocenter locations. PPA can be incorporated as part of a routine quality assurance(QA) procedure to minimize the chance of a wrong overdose. Statistical analyses demonstrated that PPA was in excellent agreement with LGP when considering the maximal dose and the arbitrary point dose for the best plan of GKRS. Due to the easy applicability we hope PPA can be widely used.

• Weed & Turfgrass Science
• /
• v.4 no.1
• /
• pp.44-48
• /
• 2015

This study was conducted to evaluate the efficacy of weed control and phytotoxicity of oxyfluorfen using a transgenic rice line (CPPO06 event) resistant to protoporphyrinogen oxidase (Protox) inhibiting herbicides in the direct-seeding flooded rice. Five annual weeds including Echinochloa oryzoides and two perennial weeds were occurred in the test field. Oxyfluorfen at 120 g a.i. $ha^{-1}$ in the application timing of two days before sowing and 0 and five days after sowing showed more than 90% weed control value except for Juglans mandshurica. Total weed control value was more than 95% in any application timing indicating a highly effective herbicide in the direct-seeding flooded rice. When compared with untreated control, no visual injuries were detected at single and double dosage of oxyfluorfen. The agronomic characteristics and yield components of CPPO06 event was reasonable in any time of application in this study. Based on these data, oxyfluorfen application before and after sowing can be applied to provide effective weed management in the direct-seeding flooded field.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.5
• /
• pp.513-521
• /
• 2012

The aim of this study was to determine the brittle fracture behavior of reactor pressure vessel steel by considering the temperature dependence of a damage model. A multi-island genetic algorithm was linked to a Weibull stress model, which is the model typically used for brittle fracture evaluation, to improve the calibration procedure. The improved calibration procedure and fracture toughness test data for SA508 carbon steel at the temperatures $-60^{\circ}C$, $-80^{\circ}C$, and $-100^{\circ}C$ were used to decide the damage parameters required for the brittle fracture evaluation. The model was found to show temperature dependence, similar to the case of NUREG/CR-6930. Finally, on the basis of the quantification of the difference between 2- and 3-parameter Weibull stress models, an engineering equation that can help obtain more realistic fracture behavior by using the simpler 2-parameter Weibull stress model was proposed.