• Korean journal of applied entomology
• /
• v.41 no.3
• /
• pp.217-223
• /
• 2002

The chestnut brown chafer, Adoretus tenuimaculatus Waterhouse, is serious insect pests in golf courses. Adults feed on the leaves of latifoliate trees but larvae feed on roots of turfgrases such as bentgrass, Agrostis spp. Damage of A. tenuimaculatus larvae was observed at the Jinju golf club which showed damage symptom on perennial ryegrass, Lolium perenne in tees and fairways in July, 2000. Damaged turf by A. tenuimaculatus larvae became yellowish and wilted. Symptom of laval damage of A. tenuimaculatus was similar to summer depression in warm season turfgrasses but not recovered by irrigation when Korean isolates of entomopathogenic nematodes were evaluated for the control of A. tenuimaculatus larvae in laboratory and field as a possible biological control agent. The nematodes used were Heterorhabditis bacteriophora Jeju strain, Hererorhabditis sp. Gyeongsan strain, Steinernema carpocapsae Pocheon strain, S.glaseri Dongrea strain, and S.longicaudum Nonsan strain. In the laboratory test H.bacreriophora Jeju strain and Heterorhabditis sp. Gyeongsan strain were highly effective for 3rd instars with 95% mortality. In the field test reduction rates of A.tenuimaculatus larvae were higher by ranging from 28 to 57% by H. bacteriophora Jeju strain, Heterorhabditis sp. Gyeongsan strain, and S.carpocapsae Pocheon strain compared to 7% by natural cause.

• The Journal of Engineering Geology
• /
• v.23 no.3
• /
• pp.247-256
• /
• 2013

The carbonate sands of the Sabkha layer in the Middle East have very low shear strength. Therefore, instant settlement and time-dependent secondary settlement occur when inner voids are exposed, as in the case of particle crushing. We analyzed settlement of the Sabkha layer under a large-scale foundation by hydrotesting, and compared the field test results with the results of laboratory tests. With ongoing particle crushing, we observed the following stress-strain behaviors: strain-hardening (Sabkha GL-1.5 m), strain-perfect (Sabkha GL-7.0 m), and strain-softening (Sabkha GL-7.5 m). General shear failure occurred most frequently in dense sand and firm ground. Although the stress-strain behavior of Sabkha layer carbonate sand that of strain-softening, the particle crushing strength was low compared with the strain-hardening and strain-perfect behaviors. The stress-strain behaviors differ between carbonate sand and quartz sand. If the relative density of quartz sand is increased, the shear strength is also increased. Continuous secondary compression settlement occurred during the hydrotests, after the dissipation of porewater pressure. Particle crushing strength is relatively low in the Sabkha layer and its stress-strain behavior is strain-softening or strain-perfect. The particle crushing effect is dominant factor affecting foundation settlement in the Sabkha layer.

• International Journal of Concrete Structures and Materials
• /
• v.6 no.2
• /
• pp.79-85
• /
• 2012

This paper presents the differences in growth of time-dependent strain values in reinforced cement concrete (RCC) and pre-stressed concrete (PSC) flexural members through experiment. It was observed that at any particular age, the time-dependent strain values were less in RCC beams than in PSC beams of identical size and grade of concrete. Variables considered in the study were percentage area of reinforcement, span of members for RCC beams and eccentricity of applied pre-stress force for PSC beams. In RCC beams the time-dependent strain values increases with reduction in percentage area of reinforcement and in PSC beams eccentricity directly influences the growth of time-dependent strain. With increase in age, a non-uniform strain develops across the depth of beams which influence the growth of concave curvature in RCC beams and convex curvature in PSC beams. The experimentally obtained strain values were compared with predicted strain values of similar size and grade of plane concrete (PC) beam using ACI 318 Model Code and found more than RCC beams but less than PSC beams.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.6
• /
• pp.791-798
• /
• 2004

Fatigue crack initiation lives of round cylindrical notch specimen were investigated. Firstly, local strain approximation methods, such as the modified incremental Neuber's rule and the modified incremental Glinka's equivalent strain energy density(ESED) rule, were used to get multiaxial stress and strain state components at the notch tip. Based on the history of local stress and strain, multiaxial fatigue models were used to obtain fatigue crack initiation lives. Because the solution of Neuber's rule and Glinka's ESED rule make the upper and lower bound of local strain approximations, fatigue crack initiation lives are expected to place between life predictions by two local strain approximations. Experimental data were compared with the fatigue crack initiation life prediction results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.9
• /
• pp.2205-2213
• /
• 1993

The characteristic test for gage factors of temperature self-compensated strain gages at cryogenic temperature is presented. By joining the international round robin test on electrical strain gages at cryogenic temperatures, the gage factors of three kinds of widely-used strain gages are obtained at the room temperature, the temperatures of liquid nitrogen and liquid helium. The calibration system which produce precise bending strain is by mechanical loading at cryogenic temperature. This paper also presents the creep characteristic of strain gages at maximum strain level.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.184-189
• /
• 2000

Two types of fiber-optic sensors, EFPI(extrinsic Fabry-Perot interferometer) and FBG(fiber Bragg grating), have been investigated for measurement of thermal strain and temperature. The EFPI sensor is only for measurement of thermal strain and the FBG sensor is for simultaneous measurement of thermal strain and temperature. FBG temperature sensor was developed to measure strain-independent temperature. This sensor configuration consists of a single-fiber Bragg grating and capillary tube which makes it isolated from external strain. This sensor can then be used to compensate for the temperature cross sensitivity of a FBG strain sensor. These sensors are demonstrated by embedding them into a graphite/epoxy composite plate and by attaching them on aluminum rod and unsymmetric graphitelepoxy composite plate. All the tests were conducted in a thermal chamber with the temperature range $20-100^{\circ}C$. Results of strain measurements by fiber-optic sensors are compared with that from conventional resistive foil gauge attached on the surface.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.206-214
• /
• 1996

Because of the wide variety of the composite materials, inherent variability in properties, and complex temperature and strain rate dependence, large strain behavior of these materials has not been well characterized. Large strain behavior under uniaxial tension is characterized over a range of temperatures and strain rates, and a modified simple linear viscoelastic model is fit to the observed data. Of particular importance is the strain rate and temperature dependence of these composites, and it is the primary focus of this study. The strain rate and temperature dependence is then used to predict limiting tensile strains, based on Marciniak imperfection theory. Excellent correlation was obtained between model and experiment and the results are summarized in maps of forming limit as a function of strain rate and temperature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.136-138
• /
• 2003

Strain states of clad sheets consisted of AL3003 and SUS430 were studied by FEM simulation. Main simulation parameters include roll size, reduction, material properties, material temperature, and friction between roll and material (or friction between materials). To investigate the effect of friction on the evolution of strain states, the friction coefficient between roll and material (or fraction coefficients between materials) was varied. Components of strain rate, strain were compared according to the variation of friction coefficients. And strain states during cladding were compared with those induced by simple rolling process.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.244-249
• /
• 2002

The purpose of this study is to develope the prediction method of liquation crack initiation in HAZ of laser weldment. Thermal two dimensional strain analyses were performed by FEM for bead-on-plate welding in order to obtain the plastic strain at elevated temperature in HAZ of the laser weldment. From these results, it became clear that the plastic strain at elevated temperature affected liquation crack initiation in HAZ, and it could be proposed that the critical strain, which controlled liquation crack initiation, existed. Moreover, an attempt was made to develop thermal and dynamic three dimensional strain analysis method for the laser weldment in order to obtain the plastic strain at elevated temperature in HAZ of the laser weldment in more detail and precisely.

• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.3
• /
• pp.165-171
• /
• 1992

진동하는 구조물을 설계할 때에는 그 구조물 중의 Strain이나 응력이 최대가 되는 장소나 시각을 알 필요가 있다. 지금까지의 Strain 해석에는 Strain gauge 등과 같은 접촉법이 많이 이용되고 있다. 더우기, 접촉법으로 대변형 진동을 하는 물체의 Strain을 해석하는 것은 곤란하다. 최근에는 비접촉법으로 Strain 분포를 해석하기 위해 화상처리를 이용한 계측이 행하여지고 있다. 이들의 Strain 분포를 측정하는 광학적인 방법으로는 격자법, Moire법, 홀로 그랩픽 간섭법 등이 있다. 특히 대변형이나 대Strain을 해석하는 데에는 격자법이 많이 이용되고 있는데, 종래의 격자법은 Data를 처리하는 데에 많은 시간과 노력이 소요되고 작업도 매우 복잡하며, Data의 수도 제한이 되어서 구조물의 분포의 해석 정도에 큰 영향을 미치게 된다. 본 논문 에서는 스테레오법을 이용해서 2차원 격자를 붙인 시료표면의 각 점의 3차원 좌표를 계측하고, 또 Fourier 변환 격자법을 적용하여 촬영된 2차원 격자의 화상에서 위상치를 구한다. 그리고 물체의 변형 전후의 대응 관계의 화상에서 3차원 형상과 Strain 분포를 해석하는 방법을 제안한다. 이 방법을 이용하면 진동하는 구조 물의 3차원 변위분포, Strain 분포를 정도 좋게 해석할 수가 있다.