• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.4
• /
• pp.395-408
• /
• 2012

An experimental investigation with 2.8kW Nd:YAG laser system was carried out to study the effects of different laser process parameters on the microstructure and hardness of STD11. The optical lens with the elliptical profile are designed to obtain a wide surface hardening area with uniform hardness. The Laser beam is allowed to scan on the surface of the work piece varying the power (1600, 1800 and 1900kW) and traverse speed (200, 400, 600, 800 and 1000mm/min) at three different F-numbers of lens. After laser surface treatment three zones, In the microstructure have been observed : melted zone(decarburization), heat affected zone(martensite), and the substrate.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.5
• /
• pp.153-160
• /
• 1994

In this study, residual stress and surface roughness were investigated experimentally to evaluate surface integrity on surface layer machined by CBN, ceramics and WC cutting tools. When machining difficult-to-cut material (hardened STD11 steel $H_{R}$C 60), residual stresses remaining in machined surface layer were mainly compressive. The increase of flank wear caused a shift of the compressive residual stress maximum to greater workpiece depths, but the changes did not penetrate the workpiece beneath a depth of 300 .mu. m. Surface roughness was influenced considerably by variations of the cutting speed and feed. In machining hard material, CBN and A1$_{2}$ $O_{3}$ ceramics cutting tool materials proved significantly superior to mixed ceramics A1$_{2}$ $O_{3}$-TiC and WC in evaluation of surface integrity.y.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.73-79
• /
• 2012

This paper describes the machining characteristics of the sintered carbide and die steel(STD-11) by electric discharge drilling with various tubular electrodes. Electrical discharge machining(EDM) removes material from the workpiece by a series of electrical sparks that cause localized temperatures high enough to melt or vapourize the vicinity of the charge. In the experiment. four types of electrode which have different diameter are used with the application of continuous direct current and axial electrode feed. The controlled factors include the dimension of the electrode. In drilling by EDM, the dielectric flushed down the interior of the rotating tube electrode, in order to order to facilitate the removal of machining debris the hole. The expansion increase with increasing the thickness of material and the diameter of electrode and the expansion of sintered carbide is 1.75 times large then that of die steel. The taper of machined hole decrease with increasing the thickness of material. The crater sixe of die steel is larger then thet of sintered carbide and the surface roughness of sintered carbide is 1.58 tims larger then that of die steel.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.344-349
• /
• 2005

This paper is studied on the effect of TiAlN coated ball end mill on cutting characteristic of high hardness steels in dry cutting condition without coolant. KP4 steels[HRC32] and STD11[HRC60] heat treated steels wert: used as the workpiece and WC-Co ball end mill and single and multi layer TiAlN coated ball end mill were utilized. Results showed that TiAlN coated ball end mill were increased the cutting length than WC-Co ball end mill in the cutting speed$[245\~320m/min]$ about $2\~5$ times for KP4 steels and about $2.7\~4.3$ times for STD11 heat treated steels. The multi layer TiAlN coated ball end mill is good about $1.2\~1.7$ times for KP4 steels and STD11 steels than single layer coated.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.1
• /
• pp.81-89
• /
• 2022

It is necessary to increase the surface hardness and improve the wear resistance and peeling resistance through the surface treatment and performance evaluation of the mold steel. As a result of vacuum heat treatment analysis, residual austenite measurement and surface treatment wear test, retained austenite should be removed by sub-zero treatment, and retained austenite was completely removed by treatment at -196℃. The TiMon film coated on the sub-zero treated STD11 specimen showed the lowest coefficient of friction.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.245-251
• /
• 2004

This paper is studied on the effect of TiAlN coated Ball End Mill and MQL(Minimum Quantity Lubrication) cutting condition on cutting characteristic of high hardness steels. KP4 steels[HRC32] and STD11[HRC60] heat treated steels were used as the workpiece and WC-Co ball end mill and single and multi layer TiAlN coated ball end mill were utilized in the cutting tests. MQL device was used to spray botanical oil coolant. Result showed that TiAlN coated ball end mill were increased the cutting length than WC-Co ball end mill in the cutting speed[$245{\sim}320m/min$] about $2.3{\sim}5.7$ times for KP4 steels and about $2.5{\sim}4.3$ times far STD11 heat treated steels. The multi layer TiAlN coated ball end mill is good for KP4 steels than single layer coated.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.47-54
• /
• 2003

Research during the past several years has established the effectiveness of acoustic emission (AE)-based sensing methodologies for machine condition analysis and process. AE has been proposed and evaluated for a variety of sensing tasks as well as for use as a technique for quantitative studies of manufacturing process. STD11 has been known as difficult-to-cut materials. The micro-grooving machine was developed for this study and the experiments were performed using CBN blade for machining STD11. Evaluating the machining conditions, frequency spectrum analysis of acoustic emission (AE) signals according to each conditions were applied. Fuzzy clustering method for associating the preprocessor outputs with the appropriate decisions was followed by frequency spectrum analysis. FFT is used to decompose AE signal into different frequency bands in time domain, the root mean square (RMS) values extracted from the decomposed signal of each frequency band were used as features.

• Transactions of Materials Processing
• /
• v.31 no.3
• /
• pp.129-135
• /
• 2022

The purpose of this study was to quantitatively evaluate the influence of hardness of tool materials on wear resistance in the sheet metal forming process. Punches used in the wear test were made of STD-11 and K340 tool material, and the tempering temperature was set to 530℃ and 500℃, respectively, to control the hardness of the tool materials. The punches mimic the shape of stamping tool of automotive body component to reflect its plastic deformation, and are designed to concentrate wear on the curvature region of punches. Progressive die and coil sheet were used to save time, cost, and raw sheet materials. By quantitatively measuring the wear depth of the punches, the wear behavior and mechanism of the punches were investigated, and characteristics of hardness and wear resistance according to tool materials and tempering temperatures were evaluated. Testing results indicate that the punch made of K340 tool steel with higher hardness had better wear resistance than that of STD-11 tool steel, and the hardness and wear resistance of tool steel were significantly impacted by the tempering temperature.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.6
• /
• pp.104-110
• /
• 2008

A lot of straight bevel gears have been manufactured by the cold forging process in order to improve the productivity and mechanical property of the product. The die for the cold forging of the gear needs high precision and reproducibility. In the study, cold forging die has been modeled by CAD/CAM and manufactured by machining center using ball end mill coated by (Al, Ti)N for heat-treated alloy steel(STD11, HRC 60). Through the measurement of the machined die, satisfactory dimensional accuracy and surface roughness were obtained. In the future, many 3-d cold forging dies will be directly machined instead of electric discharge machining.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.99-103
• /
• 1992

The EDM characteristics of STD11 steel with copper and graphite as electrode have been investigated by using Hansvedt SE-155B electro-discharge machine. The effects of parameters such as duty factor and frequency on electro-discharge machining were discussed. It was found that those parameters have significant influences on the relative electrode wear(REW), metal removalrate(MRR) surface integrity. When the duty factor was increased under the constant frequency of 2 KHz, the MRR was also increased and the REW was decreased. But REW was constant with higher duty factor of 50%. In the case of the smaller duty factor and the higher frequency, the surface roughness has become better. When the graphite was used as electrode at thes same condition, the tool electrode built-up phenomenon has been obsdrved.