• 한국주조공학회지
• /
• 제35권5호
• /
• pp.109-113
• /
• 2015

In this study, the measurement of FN (ferrite volume fraction) and the solution annealing ratio at a temperature of $1130^{\circ}C$ were determined with 15A elbow fittings of shell cast SSC13, and the corrosion resistance with and without austenitizing solution annealing were investigated in comparison with AISI304. The delta ferrite phase was observed in the material due to the slow cooling effect of the shell mold casting. However, the delta ferrite phase decreased gradually with the solution annealing at a temperature of $1130^{\circ}C$. The hardness generally decreased with a heat treatment; however, its corrosion resistance was improved with the heat treatment. In addition, when a passivation treatment was applied, its corrosion ratio showed the lowest value. The pattern of general corrosion decreased due to the decrease in the delta ferrite phase with the solution annealing treatment. Consequently, it is suggested that the corrosion resistance of SSC13 elbow fittings can be improved by increasing the ratio of any solution annealing treatment used and by decreasing the ferrite phase. The relationship between the ratio of solution annealing and delta ferrite is expressed as follows: SA (solution annealing ratio,%) = 98 - FN (ferrite volume fraction, %).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1078-1080
• /
• 1993

The quench performance and ramp rate sensitivity of eighteen 5-cm-aperature, 15-m-long SSC dipole magnet prototypes are discussed. All the magnets appear to reach a quench plateau near their extrapolated short sample current limit and well in excess of the operating current with very little training. Most of the magnets, however, exibit a dramatic degradation of thier quench current as a function of ramp rate, which for the most part, can be attributed to large cable eddy currents.

• 원예과학기술지
• /
• 제35권4호
• /
• pp.446-455
• /
• 2017

본 연구는 참외의 소비자 기반 품질 지표를 제공하기 위하여 이화학적 특성 및 관능 특성을 조사하였다. 참외는 착과 후 20일, 25일, 그리고 30일에 수확하였으며, 각 수확 시기에 따라 부피별로 소, 중, 대를 구분하여 총 9그룹의 특성을 분석하였다. 착과 후 25일 및 30일에 수확된 그룹은 20일에 수확된 그룹에 비하여 CIE $a^*$와 $b^*$값, 그리고 가용성 고형분 함량(SSC)이 높았으며, CIE $L^*$값과 경도는 낮았다. 또한 착과 후 25일 및 30일에 수확된 그룹은 전반적인 기호도가 높았다. 특성간 상관성 분석결과 이화학적 특성(CIE 값, SSC, 산도, 그리고 경도)과 전반적인 기호도는 1% 유의수준에서 상관성이 있었다. 관능 특성 평가결과 수확 시기가 늦을수록 당도와 황색도는 높고 경도는 낮았으며, 이러한 특성은 전반적인 기호도의 증가와 연관이 있었다. 주성분 분석결과 제 1주성분과 제 2주성분은 각각 62.16%와 17.91%의 설명력을 보여주었으며 전체 설명력은 80.07%였다. 제 1주성분 점수의 변화 경향을 활용하여 전반적인 기호도와 직선회귀식을 산출한 결과 $r^2$은 0.87이었다. 본 실험결과 이화학적 특성인 CIE 값과 SSC, pH, SSC/적정 산도(TA) 및 경도와 관능적 품질 특성인 과피의 황색도, 향, 풍미, 단맛, 조직감, 이미, 그리고 태좌부의 상태를 참외의 품질지표로 활용하여 소비자 기호도 예측이 가능하였다.

• Nuclear Engineering and Technology
• /
• 제47권2호
• /
• pp.176-186
• /
• 2015

Pattern classifications have become important tools for fault diagnosis in nuclear power plants (NPP). However, it is often difficult to obtain training data under fault conditions to train a supervised classification model. By contrast, normal plant operating data can be easily made available through increased deployment of supervisory, control, and data acquisition systems. Such data can also be used to train classification models to improve the performance of fault diagnosis scheme. In this paper, a fault diagnosis scheme based on semisupervised classification (SSC) scheme is developed. In this scheme, new measurements collected from the plant are integrated with data observed under fault conditions to train the SSC models. The trained models are subsequently applied to new measurements for fault diagnosis. In comparison with supervised classifiers, the proposed scheme requires significantly fewer data collected under fault conditions to train the classifier. The developed scheme has been validated using different fault scenarios on a desktop NPP simulator as well as on a physical NPP simulator using a graph-based SSC algorithm. All the considered faults have been successfully diagnosed. The results have demonstrated that SSC is a promising tool for fault diagnosis in NPPs.

• 대한토목학회논문집
• /
• 제36권6호
• /
• pp.1023-1035
• /
• 2016

부유사 농도는 유사이송해석, 하천 및 구조물의 안정성 평가 등에 있어서 매우 중요한 자료라 할 수 있다. 그러나, 국내의 경우 주로 재래식 채집방식으로 유사량을 관측하고 있어 유사량 자료가 현저히 부족한 실정이다. 이에 본 연구에서는 수평초음파도플러유속계(H-ADCP)에서 제공하는 신호대잡음비(SNR)와 레이저부유사측정기(LISST-100X)를 활용한 실측 부유사농도와의 상관관계를 구축하여 H-ADCP를 활용하여 공간 시간적으로 정밀한 유사량을 지속적으로 추정할 수 있는 기법을 개발하고자 한다. 이를 위해 H-ADCP의 신호대잡음비 보정식을 개발하였으며, 실규모 하천에서 유사를 인위적으로 공급하며 H-ADCP와 LISST를 활용하여 신호대잡음비와 부유사농도 자료를 계측하고, 개발된 보정식이 적용된 신호대잡음비-부유사농도(SNR-SSC) 관계식을 시범적으로 구축해 보았다. 구축한 SNR-SSC 관계로부터 상관계수 0.85~0.88의 상대적으로 높은 상관도를 가진 선형회귀식을 구성할 수 있었으며, 본 연구 결과는 자동유량측정장치로 사용되고 있는 H-ADCP를 적절히 활용할 경우 실시간 유사량 관측이 가능하다는 점을 시사한다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(1)
• /
• pp.542-547
• /
• 1997

In the SSC(Super System Code), the reactivity feedback models of the Doppler effect and fuel axial expansion were modified to evaluate the safety performance of the metal-fueled core. The core radial expansion model was developed and implemented into the code as well. The transient analyses have been performed by the modified SSC for UTOP, ULOHS, ULOF/LOHS, and UTOP/LOF/LOHS events for one of the core design options being considered. Analysis results shows that the reactivity feedbacks can provide an inherent shutdown capability in response to key anticipated events without scram. Development of other reactivity feedback models and validation of these models against experimental data would make the SSC suitable for the assessment of the metal-fueled core safety performance.

• Asian-Australasian Journal of Animal Sciences
• /
• 제31권4호
• /
• pp.480-488
• /
• 2018

Objective: Average daily gain (ADG) is an important target trait of pig breeding programs. We aimed to identify single nucleotide polymorphisms (SNPs) and genomic regions that are associated with ADG in the Duroc pig population. Methods: We performed a genome-wide association study involving 390 Duroc boars and by using the PorcineSNP60K Beadchip and two linear models. Results: After quality control, we detected 3,5971 SNPs, which included seven SNPs that are significantly associated with the ADG of pigs. We identified six quantitative trait loci (QTL) regions for ADG. These QTLs included four previously reported QTLs on Sus scrofa chromosome (SSC) 1, SSC5, SSC9, and SSC13, as well as two novel QTLs on SSC6 and SSC16. In addition, we selected six candidate genes (general transcription factor 3C polypeptide 5, high mobility group AT-hook 2, nicotinamide phosphoribosyltransferase, oligodendrocyte transcription factor 1, pleckstrin homology and RhoGEF domain containing G4B, and ENSSSCG00000031548) associated with ADG on the basis of their physiological roles and positional information. These candidate genes are involved in skeletal muscle cell differentiation, diet-induced obesity, and nervous system development. Conclusion: This study contributes to the identification of the casual mutation that underlies QTLs associated with ADG and to future pig breeding programs based on marker-assisted selection. Further studies are needed to elucidate the role of the identified candidate genes in the physiological processes involved in ADG regulation.

• Bulletin of the Korean Chemical Society
• /
• 제34권1호
• /
• pp.139-142
• /
• 2013

A study was carried out to evaluate the solid phase micro-extraction (SPME) for formaldehyde emission analysis of uncoated plywood. In SPME, formaldehyde was on-fiber derivatized through headspace extraction and analyzed by gas chromatography coupled with mass spectrometry (GC/MS). The SPME was compared with desiccators (DC-JAS 233), small-scale chamber (SSC-ASTM D6007) and liquid-liquid extraction (LLE-EPA 556) methods which were performed in accordance with their respective standards. Compared to SSC (RSD 4.3%) and LLE (RSD 5.0%), the SPME method showed better repeatability (RSD 1.8%) and not much difference from DC (RSD 1.4%). The SPME has proven to be highly precise (at 95% confidence level) with better recovery (REC 102%). Validation of the SPME method for formaldehyde quantitative analysis was evidenced. In addition, the SPME by air sampling directly from plywood specimens (SPME-W) correlated best with DC ($r^2$ = 0.983), followed by LLE ($r^2$ = 0.950) and SSC ($r^2$ = 0.935).

• 한국수정란이식학회지
• /
• 제32권4호
• /
• pp.343-351
• /
• 2017

Porcine spermatogonial stem cells (SSCs) prefer three-dimensional (3D) culture systems to 2D ones for the maintenance of self-renewal. Of the many 3D culture systems, agar-based hydrogels are candidates for supporting porcine SSC self-renewal, and there are various types of agar powder that can be used. In this study, we sought to identify an agar-based 3D hydrogel system that exhibited strong efficacy in the maintenance of porcine SSC self-renewal. First, 3D hydrogels with different mechanics were prepared with various concentrations of Bacto agar, lysogeny broth (LB) agar, and agarose powder, and the 3D hydrogel with the strongest alkaline phosphatase (AP) activity and greatest increase in colony size was identified for the different types of agar powder. Second, among the porcine SSCs cultured in the different 3D hydrogels, we analyzed the colony formation, morphology, and size; AP activity; and transcription and translation of porcine SSC-related genes, and these were compared to determine the optimal 3D hydrogel system for the maintenance of porcine SSC self-renewal. We found that 0.6% (w/v) Bacto agar-, 1% (w/v) LB agar-, and 0.2% (w/v) agarose-based 3D hydrogels showed the strongest maintenance of AP activity and the most pronounced increase in colony size in the culture of porcine SSCs. Moreover, among these hydrogels, the strongest transcription and translation of porcine SSC-related genes and largest colony size were detected in porcine SSCs cultured in the 0.2% (w/v) agarose-based 3D hydrogel, whereas there were no significant differences in colony formation and morphology. These results demonstrate that the 0.2% (w/v) agarose-based 3D hydrogel can be effectively used for the maintenance of porcine SSC self-renewal.

• Animal Bioscience
• /
• 제37권3호
• /
• pp.451-460
• /
• 2024

Objective: The objective is to identify genomic regions and candidate genes associated with age to 105 kg (AGE), average daily gain (ADG), backfat thickness (BF), and eye muscle area (EMA) in Yorkshire pig. Methods: This study used a total of 104,380 records and 11,854 single nucleotide polymorphism (SNP) data obtained from Illumina porcine 60K chip. The estimated genomic breeding values (GEBVs) and SNP effects were estimated by single-step genomic best linear unbiased prediction (ssGBLUP). Results: The heritabilities of AGE, ADG, BF, and EMA were 0.50, 0.49, 0.49, and 0.23, respectively. We identified significant SNP markers surpassing the Bonferroni correction threshold (1.68×10^-6), with a total of 9 markers associated with both AGE and ADG, and 4 markers associated with BF and EMA. Genome-wide association study (GWAS) analyses revealed notable chromosomal regions linked to AGE and ADG on Sus scrofa chromosome (SSC) 1, 6, 8, and 16; BF on SSC 2, 5, and 8; and EMA on SSC 1. Additionally, we observed strong linkage disequilibrium on SSC 1. Finally, we performed enrichment analyses using gene ontology and Kyoto encyclopedia of genes and genomes (KEGG), which revealed significant enrichments in eight biological processes, one cellular component, one molecular function, and one KEGG pathway. Conclusion: The identified SNP markers for productive traits are expected to provide valuable information for genetic improvement as an understanding of their expression.